Telenet Systems Pvt. Ltd. Ghatkopar, Mumbai, Maharashtra

Telenet TNDSL 2240 ADSL2 + router is a high quality equipment which can be used as a ADSL MODEM, a wireless AP and a router. Choose the slap-up chipset TNETD7300A provided by the global famous ADSL CMOS corporation TI, which supports kinds of network protocols, steady runs, and is compatible with various DSLAM, which is preferred by the individual users, the SOHO, and the small enterprise to access the internet. Features: Four 10/100 Ethernet port with ONE USB(optional) Friendly GUI for web configuration Support Single-Session IPSec and PPTP Pass-Through for Virtual Private Network (VPN) Several popular games are already pre-configured. Just enable the game and the port settings are automatically configured. Configurable as a DHCP Server on Your Network Compatible with virtually all standard Internet applications Industry standard and interoperable DSL interface Address Filtering, DMZ Hosting, and Much More Simple web based status displays a snapshot of your system configuration and links to the configuration pages Downloadable flash software upgrades Support for up to 8 Permanent Virtual Circuits (PVC) Support for up to 8 PPPOE sessions High-Speed Data Transfer Rates of up to 54Mbps Compatible with IEEE 802.11b, IEEE 802.11g, 2.4GHz Compliant Equipment    

Features:   One 10/100 Ethernet port Friendly GUI for web configuration Support single session IP sec and PPTP pass through for virtual private network (VPN) Several popular games are already pre-configured. Just enable the game and the port setting are automatically configured Configure as a DHCP server on your network Compatible with virtually all standards internet application Industry standard and interpretable DSL interface Address filtering, DMZ hosting, and much more Simple web base status page display a snapshot of your systems configuration and link to the configuration pages Downloadable flash software upgrades Support for up to 8 permanent virtual circuits (PVC) Support for up to 8 PPPoE sessions High-speed data transfer rates of up to 54 Mbps Compatible with IEEE 802.11b, IEEE 802.11g, 2.4GHz compliment equipment   Standard:   ANSI T1.413 issue 2 ITU G.992.1 (G.dmt) ITU G.992.2 (G.dmt) ITU G.992.3 (G.dmt) ITU G.992.2 (G.dmt) IEEE 802.11b_IEEE802.11g   Specification Signal:   ATM T1.413 issue2 Strict ATM communicating mode   Data Speed:   Downstream data rates up to ADSL 8Mbps; ADSL+2 24Mbps Upstream data rates up to 1024kbps G.lite; downstream data rates up to 1.5Mbps G.lite up streams data rates up to 51kbps  

GENERAL General Standard 3GPP Release 9   Interface Universal serial bus 2.0 compatibility (USB 2.0 certified)   SIM Mini-SIM interface   Operation modes Time Division Multiplexing TDD   UE Category   Category 4 U   QoS   QCI1-9 supported (both GBR & non-GBR) Network and UE initiated dedicated bearer support   Certification Compliant to GCF Certification       MANAGEMENT Management Remote Management   Security USIM authentication Physical: Mini-SIM slot   Remote Configuration & Software Upgrade Downloadable, self-extracting software bundle for SW upgrade and device management    Connection Manager Windows and Mac OS X versions CD-less installation from USB stick Client for OTA software upgrade Diagnostics utility Custom operator branding (optional)       RADIO Number of Radio TD-LTE Radio   Frequency Range 2300 - 2400 Mhz   Channel Bandwidth Bandwidth 5MHz/10MHz/15MHz/20MHz Support   RF tranmission power 23 dBm   Receiver Sensitivity -94 dBm   MIMO capability 1 T x 2 R       ANTENNA Internal Antenna gain 2 dBi   External Antenna Connector 1 (Optional)       OPERATING SYSTEM OS Compatibility Windows XP, Vista and 7 Linux Mac OS 10. 5 or higher       POWER Power Requirements 5V DC at 500mA approx   Power Consumption 2.5 Watts Max       INSTALLATION Plug & Play Operation CD-Less installation offering a plug & play experience to users       PHYSICAL Physical Dimension/ Form factor USB Dongle with in-built antenna. Compact Form factor, Not larger than current 3G Dongles   Weight < 50 g   Operating temperature . (0 to 50 )deg cent   Humidity 5 to 90% Non Condensing       ENVIRONMENT PROTECTION Compliances WEEE, EN 60950,CE mark, RoHS Directive 2002/95/EC Other market specific certification upon requests   Shock and Vibration ETSI300-0110-1.4   Enclosure Characteristics   Plastic

Telenet’s TPC 3020 E1 to V.35 protocol converter can realize the bi-directional data transfer from E1 port to V.35.This equipment is widely used in communication network including WAN and LAN, realizing the transfer from E1 channel of SDH or PDH equipment to V.35 which maybe provided with router. Features:   E1 channel: both framed & unframed are OK, both 75 & 120ohm are OK Standard: G.703, line code: HDB3 Alarm system for E1 loss Support local/remote loop test DB25 connector for V.35, in DCE mode Multiple clock selection: internal clock, V.35 line clock and E1 recovery clock Panel instruction for easy understanding of equipment working status Internal power supply, 220V AC and -48V DC optional Standalone and module at your selection   Specifications:   E1 Port   Bit rate: 2.048Mbit/s+-50ppm Line code: HDB3 Standard: Compatible with ITU-T G703 Connector: BNC connector with line impedance 75ohm, RJ45 connector with line impedance 120ohm Jitter performance: in full compatible with G742 and G823 V.35 port   Line code: NRZ Bit rate: 2.048 Mbit/s+-50ppm Connector: DB25female, with DB25/M34 transfer line Way of Connection: DCE Clock: Line Clock, Local clock   General   Operating temperature: 0-50 °C Power Supply: -48VDC or 220VAC+-20% Dimension: 170mm(W)*133mm(D)*40mm(H)  

Telenet’s Midspan POE is a Power-over-Ethernet (Poe) power supply which provides DC power for one Poe-equipped device by "Injecting" DC power through the Spare Pair of the CAT5 (10/100Mbps) Ethernet cable.   Electrical Specifications Nominal Operating Voltage VN 230 V AC, 1 Phase,50 Hz ± 1%   Input Operating Voltage Range 140V – 300 V AC ± 1%   Output Voltage Range 24V ± 5%   Output Current 1AMP ± 1%   Ripple & Noise at I/P 230V AC & Full Load 100Mv Line & Load Regulation ±3% Working environment Temperature -40 - +55c Humidity relative 90% (25c), altitude 3km Protections Input Surge protection Output Overload ± 5% & short circuit Product Safty Insulation resistance 5ohm when tested with 500Vdc Dielectric voltage withstand test Between shorted input & output Terminals 1.5kv AC rms for 1min Terminations A C input 3 pin plug-in type as per IS power cord 3 pin power cord Enclosure Material ABS plastic Accessibility easy accessible to open top & bottom cover POE Injector Power over Ethernet injector 24V @ 24W on spare pair Cat-5 cable data lines Pair1: pins 1/2, pair2: 3/6 Cat-5 cable power lines -V dc pins 4/5, + Vdc pins 7/8 Connector 2 RJ 45 Metallic Ports  

Telenet’s Midspan POE is a Power-over-Ethernet (Poe) power supply which provides DC power for one Poe-equipped device by "Injecting" DC power through the Spare Pair of the CAT5 (10/100Mbps) Ethernet cable Installation and Management Plug and Play installation. Our POE device automatically supplies inline power. Local Power LED is present

Telenet’s Midspan POE is a Power-over-Ethernet (PoE) power supply with integral DC Injector. It is a single-port Power-over-Ethernet (PoE) Midspan to feature gigabit switching support and high efficiency four-pair operation compliant with the IEEE 802.3at power-over Ethernet (PoE) power specifications. It provides DC power for one PoE-equipped device by "Injecting" DC power through the CAT5e Ethernet cable. Telenet’s Midspan PoE can source 15W to 120W of Power: Telenet’s Midspan PoE can deliver power as per the IEEE802.3af and IEEE802.3at standards. Simultaneously for Power Devices that demand more power than that specified by these standards we have a proprietary range, wherein power can be sourced on 2-pair as well as 4-pairs, also this per port power rating can be increased from 30W up to 240W, thereby considerably increasing the delivered to the Power Device.   Telenet’s Midspan POE is a Power-over-Ethernet (PoE) power supply with integral DC Injector. It is a single-port Power-over-Ethernet (PoE) Midspan to feature gigabit switching support and high efficiency four-pair operation compliant with the IEEE 802.3at power-over Ethernet (PoE) power specifications. It provides DC power for one PoE-equipped device by "Injecting" DC power through the CAT5e Ethernet cable. Telenet’s Midspan PoE can source 15W to 120W of Power: Telenet’s Midspan PoE can deliver power as per the IEEE802.3af and IEEE802.3at standards. Simultaneously for Power Devices that demand more power than that specified by these standards we have a proprietary range, wherein power can be sourced on 2-pair as well as 4-pairs, also this per port power rating can be increased from 30W up to 240W, thereby considerably increasing the delivered to the Power Device. Specification Ethernet Connectors RJ45 Jacks (2) Ethernet data rate 10/100/1000Mbps Ethernet No. of Ethernet Devices that can be powered Single Data Lines Pair 1: Pins 1/2 Pair 2: Pins 3/6 CAT-5 Power (PoE) Pinout + VDC: Pins 4/5 - VDC: Pins 7/8 + VDC: Pins 1/2 - VDC: Pins 3/6 Nominal Output Voltage (48VDC-57VDC) (Typical: 54V) Input 110-250 VAC 50Hz OR -48V DC IEEE Compliant IEEE802.3af Compliant IEEE802.3at Type1 and Type2 Compliant. Protection Port Overload protection, Port Inrush and Short-Circuit protection, Thermal Protection, Open-Circuit Protection.   Applications for this Power-Over-Ethernet product Wireless LAN Access Points and Bridges Wifi Amplifiers and Amplified Antennas WiMAX VoIP (Voice over Internet Protocol) Telephones IP Surveillance Cameras Bluetooth® Access Points Microwave Radios

Telenet’s Midspan POE is a Power-over-Ethernet (Poe) power supply with integral DC Injector. It provides DC power for one Poe-equipped device by "Injecting" DC power through the CAT5 (10/100Mbps) Ethernet cable. It is compatible with AP’s and other equipment supporting the IEEE standard Poe pin out (Pins 4&5 Power + / Pins 7&8 Power -). Since our POE device is completely self-contained, a separate power supply and injector is not required Installation And Management Plug and Play installation. Our POE device automatically detects all POE enabled devices and supplies inline power. Local LED Management display is present. Application Wireless LAN Access Points and Bridges Wireless LAN Wi-Fi Amplifiers and Amplified Antennas VoIP (Voice over Internet Protocol) Telephones IP Surveillance Cameras Bluetooth® Access Points     Electrical Specifications Ethernet connectors RJ45 jack (2) Ethernet data rate 10/100 Mbps Ethernet No. of Ethernet Devices that can be powered Single Data Lines Cat-5 power(POE) pin out ( spare pare ) Pair 1 : pin 1/2 Pair 2 : pin 3/6 +VDC : pin 4/5 -VDC : pin 7/8 Operating temperature 0* C to +55* C Max output power 16W Normal output voltage 44 v to 55 v Input 110 – 250vac 50hz IEEE Compliant Single IEEE 802.3af compliment

Telenet’s TWI series of 802.11b/g/n compliant 2.4GHz Wireless LAN products feature 1x1 and 1x2 MIMO antennas. These come in various form factors – For Outdoor applications as a CPE, for outdoor application as an AP, for an indoor AP/Router. It can operate in Point-to-Point and Point-to-Multi-Point links. It can be configured in WDS mode as well.   It can be available with Wireless WAN and Wireless LAN capabilities as well. The TWI series has a high performance radio output and advanced networking and management capabilities. It can support NAT Routing, DHCP server, DHCP relay, DHCP with option 60, QoS, Security based on WPA2/WPA/WEP, Rate Limiting, Broadcast Storm control, etc.   For different applications suitable antennas are provided with appropriate gains. It could have a single antenna for a 1x1, to a multipolarized antenna, and a MIMO antenna for 1x2.   The housing are built according to the applications, such as indoor housing and outdoor housing with ruggedized weatherproof design to meet various IP classes of protection.   GENERAL General Standard IEEE 802.11b/g/n WLAN, IEEE 802.3/802.3u Ethernet   Ethernet Interface Four auto MDX, auto sensing 10/100 Mbps, RJ45 port   Operation modes Station/Station + WDS       SYSTEM CPU 400 Mhz   Flash / SDRAM 4 or 8 MB/16 MB       NETWORKING Networking DHCP client, Configurable DHCP option 60   Test PING function and Trace Route function   VLAN VLAN Support; Management VLAN       ROUTER FEATURE Networking NAT, DHCP Client/Server, DNS Proxy   VPN PPTP/L2TP/IPSec pass-through Pass through       RADIO Number of Radio One 802.11 b/g/n Radio   Frequency Range 2400 - 2490Mhz   Channel Number ETSI 1-13   Channel Bandwidth Narrow Bandwidth 20 / 40 MHz Support ; Auto in STA mode   RF transmission power 20Dbm   Receiver Sensitivity -94 dBm       ANTENNA Internal Antenna gain 8dBi   Internal Antenna3 dB Beamwidth 65 Degrees / 65 Degrees   Internal Antenna Polarization Horizontal Polarization       MANAGEMENT NMS Can be Integrated with Centralised Web Based Management System for Monitoring,Configuration and Software Upgrade   Management – Device HTTP Web-based GUI, Telnet Management, button for factory reset,   Firmware Upgrade Automated centralised Firmware Upgrade &WebGUI manual upgrade ; Keep setting when Firmware Upgrade   LED indication Power, Ethernet , Wireless signal strength       ETHERNET INTERFACE -SPECIFICATION Ethernet Connectors RJ-45 Jacks, 4 Ports 10/100 Base-TX with Auto-MDIX 4-Ports PoE (Data+Power IN)   Standards IEEE Std.802.2 10BASE-T 10Mbps,Half/Full Duplex; IEEE Std.802.23u 100BASE-TX,10/100Mbps, Half/Full Duplex;IEEE Std.802.3x Flow control and Back-pressure.   Surge Protection Protection against initial ESD/EFT Transient Suppression   Protocols CSMA/CD   Technology Store & Forward switching architecture   Network Cable 2-Pair UTP/STP Cat 5 24AWG Cable   LED’s Link/Activity per Ethernet Port   Power Over Ethernet Injector: Power Supply(IN) for CPE. Power over Ethernet 12V, 1A (12 Watts) on Spare pair to supply power to the CPE   No. of Ethernet Ports that can Power ON the CPE. Anyone/All of the four LAN ports   Max Packet size supported 1536 bytes   Port Isolation Using Port-based VLAN   Support Broadcast Storm control per port Yes       SECURITY Wireless Security WEP, WPA2 - PSK(TKIP/AES) WPA2-AES with 802.1x 802.1x Supplicant EAP-TTLS MSCHAPV2, EAP-TTLS support       POWER Power options 100-270 V 50/60 Hz, Indian PIN type Powering through POE DC power   Power Method Passive Power over Ethernet   Max Power Consumption 4 Watts   Power Supply 12V, 1A (12 Watts). Power Supply and POE injector included       PHYSICAL Physical Dimension/ Form factor Compact and easily mountable on house window   Enclosure Size 175 x 168 x 52 mm   Weight

The Telenet TSW 1010 XA switch is an full L2 management 8-port Fast Ethernet switch, plus 2 Gigabits port (support auto copper/fiber switching), with high performance and competitive price. It's a perfect way to extend your network structure.       FEATURES   Compliant with the IEEE802.3 10Base-T Ethernet, IEEE802.3u 100Base-TX IEEE802.3ab 1000Base-T ,IEEE802.3z 1000Base-X specifications 8 port 10/100Mbps TX Auto-Negotiation and 2 port 10/100/1000Mbps TX and 2 1000Mbps SFP port(shared with 10/100/1000M port) Supports TP interface Auto MDIX function for auto TX/RX swap Support up to 8K MAC address Up to 1M bits packet buffer Supports Store & Forward architecture and performs forwarding and filtering Supports to handle up to 1522 bytes packet Supports 8 groups Port-Based VLAN and 512 groups 802.1q tag VLAN Supports rate control(64Kbps-80Mbps) Supports port mirror Supports IEEE802.1D Spanning Tree and IEEE802.1w RSTP protocol filter Supports MAC address and binding(up to 400 rules) Supports IGMP snooping Supports port trunking(up to 12 groups and 8 ports in each group) Supports SNMP V1/V2 ,RMON MIB(group 1,2,3,9) Supports access switch through Web/Telnet/Console Supports firmware upgrade through Web/Console Build-in power     Technical Specifications Standards IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX，IEEE802.3ab 1000Base-T,IEEE802.3z 1000Base-X Access Method CSMA/CD Network Media UTP CAT3 or up for copper port ,Single-mode or Multi-mode fiber(with SFP connect) for fiber port Transmission Method Store and Forward MAC Address 8K Built-in Buffer 1M bits Data Transfer Rate 10/100Mbps (Half-duplex), 20/200/2000Mbps (Full-duplex for copper port) 2000Mbps only for fiber port LED Indicators Power, Link/Activity Dimension 280mm(L) x 173mm(W) x 44mm(H) Weight 4000g Temperature 0° to 50° C (operating), -20° to 70° C (storage) Humidity 5% to 90 % non-condensing (operating), 5% to 90% non-condensing (storage) Certifications FCC Part 15 ark Class A, CE M Input 12V DC   Technical Specifications Standards IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX，IEEE802.3ab 1000Base-T,IEEE802.3z 1000Base-X Access Method CSMA/CD Network Media UTP CAT3 or up for copper port ,Single-mode or Multi-mode fiber(with SFP connect) for fiber port Transmission Method Store and Forward MAC Address 8K Built-in Buffer 1M bits Data Transfer Rate 10/100Mbps (Half-duplex), 20/200/2000Mbps (Full-duplex for copper port) 2000Mbps only for fiber port LED Indicators Power, Link/Activity Dimension 280mm(L) x 173mm(W) x 44mm(H) Weight 4000g Temperature 0° to 50° C (operating), -20° to 70° C (storage) Humidity 5% to 90 % non-condensing (operating), 5% to 90% non-condensing (storage) Certifications FCC Part 15 ark Class A, CE M Input 12V DC  

The ISDN TA with built in NT is an ISDN network Terminator with 2 a/b (POTS) ports with serial and USB built in data ports. The data port provides a high speed solution for internet access, File transfers, Remote Access services etc. Support for advanced communication software is provided via CAPI 2.0 drivers. On the Digital port up to 8 devices (with optional extender) can be terminated such as video conferencing for 64 or 128 kbps, ISDN Feature Phones, G4 fax etc. Configuration is simple, using an analog telephone or via a GUI utility provided on the data ports. The data ports are provided with drivers for easy of installation. The LED’s provided on the front give you the status at a glance also making diagnostics and to provide for ease of maintenance. The ISDN TA with built in NT also supports Network Management Services which are password protected. This helps in knowing the status of the unit also allows remote configuration that saves time required to effect changes in the configuration without the need to visit the customer’s location. Support for remote firmware upgrade is also included this helps to keep the system updated to the latest features which is very cost effective in the long run. ISDN TA with built in NT is housed in a small sturdy and aesthetically designed case.   Analog Port Features Analog Extension The ISDN TA with NT provides you with 2 extensions. For connecting fax machines, modems, etc. Supports internal communication while both B Channels are in use Configuration Setting Configuration can be done using standard phone connected to the analog port Flexible MSN usage   If you have several MSN then each MSN number can be programmed to ring any combination of extension. Distinctive Ring Each MSN number can be programmed for a different Ring tone Call pick up   Any extension can be used to answer incoming calls ringing on another extension. Clir   Before making a call, choice of deactivating and activating caller ID per call or enabling it permanently Clip Caller ID is presented on all extensions for all income calls Call forwarding   ( CFU,CFB and CFNR ) depending on condition a call can be forwarded to another subscriber Tp An exiting call can be suspended and resumed Call waiting Second incoming call is announced via special tone. Call Transfer Incoming calls on any extension can be transferred to another extension MCID   Telephone number of Malicious caller can be registered at the switch by invoking a command 3PTY While engaged in conversation you can have third party join in Emergency Mode Choice of Analog or ST ports working in case of local power failure.     Model iNT-DPS ISDN Interfaces 1x RJ 45, 2 Wire U interface, 2B1Q coding, ETR 080 S/T Interfaces   2x RJ 45, 4 wire interface, as per ANSI T1.605 standard, ETSI ETS300012, ITU-T I.430 recommendation Network Management ( NMS )   Remote configuration Remote firmware Upgrade RS232 Interface 1 X 9 pin DSUB connector female Functional V.24 Electrical V.28

Telenet’s ISDN Network Termination for basic rate access is the main gate to the world of ISDN. It enables subscribers to use services such as high-speed transmission of data, text and video signals in digital format over an access line in addition to voice transmission. It is a link between the subscriber line (U Interface) and the user Interface to the network (S/T interface). A maximum of 8 terminal units can be connected to the S/T interface. The digital transmission format used offers the subscriber the possibility of access to two independent Basic Channels (B Channels) each with 64 Kbit/s and one 16 Kbit/s Signaling Channel (D), to be transmitted. The terminals connected to S/T for any two ISDN services can use both B channels simultaneously. The associated Signaling information and various service features are transmitted over the D Channel. This result in a Transmission speed of 144 Kbits/s for both transmits and receives direction. The NT1 is installed at the end of the public transmission line coming from the ISDN switch of the local exchange and converts the 2-wire duplex U interface into the 4wire double simplex subscriber S/T interface. Features:   Up to 8 access sockets can be connected to the S/T interface via a 4-wire bus. Two services like telephony and Data transmission can operate simultaneously. Data rate of 144 Kbps is available to the customer at the S/T interface. It has three bus configurations, which have different coverage ranges. Point to Point. Point-to-Multipoint: Short passive bus. Point-to-Multipoint: Extended passive bus. Has four operating modes depending on whether transmission is active or inactive and whether the integrated power supply is working or not Echo cancellation at the U interface ensures that Data Signals are transmitted bidirectionally. The interface modules operate in the automatic mode. The U interface module recovers clock synchronization signal, monitor transmission errors and initiate appropriate actions. In the event of a long-term short circuit, the power supply module is auto switched off and resumes operation automatically with only a delay of few seconds. The design is in compliance with ITU/CCITT/ANSI/ETSI and industry standard 2B1Q line code for the Uinterface. It is easy to install at the user’s premises and can be installed in a wall-mounted cabinet or used as a desktop version. Testing and operation configurations can be adjusted quickly by means of switches and jumpers. The technical data of the NT1 is as under   U-INTERFACE Transmission method 2 Wire full duplex interface using echo cancellation   Allowable attenuation > 42 db at 40 KHz   Line Code 2B1Q   Subscriber Line Connection 8 pin jack (RJ-45)   Voltage at U-Interface 120 V (max)           S/T-INTERFACE Transmission method 4 wire duplex transmission   Range Point to point up to 1000m   Short passive bus   up to 150m up to 8 T E’ S   Extended passive bus   up to 500m up to 4 T E’ S   Interface connector for S/T   RJ-45 x 2 230 V AC   Power Supports Remote powering in absence of local power   Test function Supports loop back commands from the switch  

Features: Calling line identification presentation A to B (CLIP) Calling line identification restriction A to B (CLIR) Connected line identification presentation B to A (COLP) Connected line identification restriction B to A (COLR) Terminal portability (TP) Advice of charges (AOCE/AOCD) Hold function, two-line operation (switching Between lines) Call waiting (CW) Three-party-conference (3 PTY) Explicit call transfer (ECT) Completion of call to busy subscriber (CCBS) Call forwarding unconditional (CFU) Call forwarding on no reply (CFNR) Sub addressing for outgoing calls (SUB) Malicious call identification (MCID) Support of keypad protocol for special Functions of the network provider (KEYPAD) PC software functions Compatible with Windows®98/ME /NT®4.0/2000/XP Programming of features Entry of telephone directory Management and assignment of call data (Phone Numbers, charges etc.) Dialing from the directory via integrated dialer Update of operating software, current firmware

GENERAL General Standard 3GPP Release 9 CAT 4   Ethernet Interface Four Ports, auto MDX, auto sensing 10/100 Mbps, RJ45 ports   Operation modes Time Division Duplex TDD   QoS QCI - Throughput expectations, Packet error loss, delay, and variation in delay (Jitter.)       SYSTEM CPU 300 Mhz or better   Flash / SDRAM 4/16 MB       NETWORKING Networking Built-in DHCP client and server ,Configurable DHCP option 60 , Static route, NAT/PAT, DMZ, DHCP Client/Server/Relay, DNS Proxy, DDNS   VPN PPTP/L2TP/IPSec pass-through Pass through   Test PING function and Trace Route function   VLAN VLAN Support; Management VLAN       MANAGEMENT NMS CENTRALISED MANAGEMENT SYSTEM for Monitoring, Configuration and Software Upgrade   Management – Device HTTP & HTTPS Web-based GUI, Telnet, SSH, SSH2 Management, button for factory reset,   SNMP SNMP V1 & V2, SNMP traps for RSSI / Signal Quality Degradation, Interference, Congestion, Packet Drop   Firmware Upgrade Automated centralised Firmware Upgrade & WebGUI manual upgrade; Keep setting when Firmware Upgrade   LED indication Power, Ethernet , Wireless   Security Functions Stateful Packet Inspection, Packet filtering, Denial Of Service protection, Management   Authentication PAP, CHAP       ETHERNET INTERFACE Ethernet Connectors RJ-45 Jacks, 4 Ports 10/100 Base-TX with Auto-MDIX Port   Standards IEEE Std.802.2 10BASE-T 10Mbps, Half/Full Duplex; IEEE Std.802.23u 100BASE-TX, 10/100Mbps, Half/Full Duplex; IEEE Std.802.3x Flow control and Back-pressure.   Surge Protection Protection against initial ESD/EFT Transient Suppression   Protocols CSMA/CD   Technology Store & Forward switching architecture   Network Cable 2-Pair UTP/STP Cat 5 24AWG Cable   LED’s Link/Activity per Ethernet Port   Max Packet size supported 1536 bytes       WLAN WLAN MAC Address Filtering, WEP, WPA, IEEE 802.1X   Standard IEEE802.11n, backward compatible with 802.11b/g   Encryption WEP, WPA, WPA2   Channels 11 Channels (US, Canada), 13 Channels (Europe, Australia), 14 Channels (Japan)   WLAN Data Rate Upto 300 Mbps       RADIO Number of Radio TD-LTE Radio   Frequency Range 2300 - 2400 Mhz   Channel Bandwidth Bandwidth 5MHz/10MHz/15MHz/20MHz Support   RF transmission power 23 dBm   Receiver Sensitivity -94 dBm   MIMO capability 1 T x 2 R       ANTENNA Internal Antenna gain 2 dBi or More   Internal Antenna Polarisation Multipolarised Software Controlled Manual/Auto mode   MIMO capability 1 (Optional)       POWER Power options 100-270 V 50/60 Hz, Indian PIN type powering through DC power   Power Method DC Power Supply   Max Power Consumption 8 Watts   Power Supply 12V, 1A (12 Watts) DC External Adapter       PHYSICAL Physical Dimension/ Form factor Table top with in-built antenna   Weight < 600 g   Operating temperature (0 to 50 deg cent) Outdoor Temperature   Humidity (Specify supported value) 5 to 95% Non Condensing       ENVIRONMENT PROTECTION Compliances WEEE, EN 60950,CE mark, RoHS Directive 2002/95/EC Other market specific certification upon requests   Shock and Vibration ETSI300-0110-1.4   Enclosure Characteristics   Plastic

Features:   Eco-friendly response saves power consumption by up to 60% in stand by mode. Reliable alternative to WI-FI, elements problem created by thick walls & blind spots. Transform power line into home network of multiple computers without messes cabling. High-speed 200Mbps to streams content on HD IPTV, IP camera and game controls. “Simple connects” security feature to pair multiple home-plugs at one touch of a button.       Specifications Standards  Home plug AV IEEE 802.3 10/100 auto MDI/MDIX   Protocols TDMA & CSMA/CA   Range 200m over power line   Modulations   OFDM symbol modulation DQPSK,DBPSK,ROBO carrier modulation   LED inductors     1x power 1x power line – link /activity 1x Eth – link / activity   Security 128 bits AES encryption   External interface     Push button for simple connect Ethernet LAN port Reset button   Environment     Operating: 0* C to 40*C Storage : -25*C to 70*C Environment : 30% to 80% humidity ( non-condensing )   Physical dimension   Weight : 190g Dimension : 90(H) x 46 (W) x 75 (D) mm   Power consumption    4.0W QABA 1.6W in energy saving mode   Operating systems     O/S independent Configuration utility requirement : 98SE / ME / 2000 / XP / Vista   Package includes   1x HL110E 1X Rj 45 1x recourse CD 1x easy start guide  

Features:   Extend wireless network in to any spot at home 300Mbps Turn any power outlet into a network connection Automated security with “simple connect” button Wireless “on/off” button for convenience and ease of use Double Ethernet ports for direct connection to Ethernet-ready device Simple plug & play, no software or installation required No new wires, no drilling, no hasslel Standards     Powerline: Homeplug AV / Wireless : IEEE 802.11b/g/nEthernet : IEEE 802.3,AUTO MDI / MDIX   Protocols Powerline: CSMA/ CA over Powerline in your home Wireless: CSMA/ CA,EDCA   Modulation  Powerline : OFDM 1024/256/64/16/8 QAM,QPSK,BPSK,ROBO Wireless: CCK,BPSK,DQPSK,QPSK,QAM   Data transfer rate  Powerline: up to 200Mbps over Powerline Wireless: up to 300Mbps via wireless   Range  Powerline: up to 200m over Powerline Wireless: up to 300m via wireless   Security  Powerline : 128-bit AES encryption ( enabled with simple connect button ) Wireless: WEP,WPA,WPA2   Hardware   Powerline :intellon INT 6400 homeplug AV chipset Wireless : Wireless N chipset   LED inductors       1x power LED (PWR) 1x power line link / ACT status LED ( PL-LKACT) 1x Ethernet link / ACT status LED ( ETH-LKACT) 1x wireless link/ACT   External connectors    1x electrical power plug 2x RJ 45 for 10/100 Ethernet (AUTO MDI /MDIX ) 1x reset button 1x push button for simple connect   Dimension 105mm (H) 58mm (W) 42mm(D)   Power consumption Norminal 7.0Watt / standby 5Watt / 1.2A   Power supply AC 100-240V / 50-60 Hz   Temperature   Operating :0* C to40*C, 30% to 80% relative humidity Non-operating : -25*C to 70*C, 30% to 95% relative humidity   Operating systems   Windows 98 / 98SE / ME / 2000 / XP / VISTA ( 32/64-bits)  

Telenet’s TPC 3010 Protocol Converter is a high performance, remote, self-learning Ethernet Bridge. Its compact size and low cost make it ideal for cost-sensitive bridging applications or as a LAN extender over bit stream type infrastructures. Its E1 data interface also provides an economical digital access solution for E1 and Fractional E1 network Services, which can work at data rates of 64Kbps to 2048Kbps.User data is placed into the E1 frame, using only the required number of timeslots. Timeslot assignment is accomplished according to the Data Port speed and manual setting of DIP switches. The main E1 link may be clocked from the recovered receive clock or from an internal oscillator. For easy to check the fault of network line, the device provides loop selection, both local loop and remote loop. Features:   High performance bridge for 10Base-T Ethernet extension Fully compatible with IEEE 802.3 and Ethernet Standards E1 channel with both framed & unframed, both 75 & 120ohm Ethernet Port 10Mbps, Full/Half Duplex Mode compatible Ethernet ports support MDI/MDI-X selection able Allow transmitting and receiving VLAN data packet 15000 frames per second filtering and forwarding rate 1000 MAC address LAN table, and automatic LAN table learning and aging. Standalone and Module optional Power of Chassis 2 Slots for slide in power supplier module, AC or DC power supplier module, Redundant Power supported AC220V+-20%or DC-48V power input.   Standard Standard ITU G.703, G.704   Jitter Performance According to ITU G.823   Bit rate N*64Kbps, N=1~31 (Fractional Mode) or 2.048Mbps(Full Mode)   Line Code HDB3   Line Impedance 75/120ohms optional   Pulse Amplitude Nominal 2.37V+-10%       GENERAL Voltage AC 220V+-20%or DC -48V   Power Consumption 3 Watts   Temperature 0-50Oc   Humidity 0-90%(non-condensing)   Size (Width from left to right)   Standalone 272mm(Width)*139mm(Deep)*41mm(High)   Chassis 438mm(Width)*252mm*Deep)*178mm(High).   Standard Conforms to IEEE802.3 / 10Base-T Ethernet Data rate   10Mbps (20Mbps/10Base-T in Full duplex topology) Compatible on Full/Half duplex topology Connectors RJ-45 Connector  

This device is a well-designed high-speed and high performance ADSL + 2 router, which supports kind of network protocols, steady runs, and is compatible with various DSLAM, which is preferred by the individual users, the SOHO,small enterprise to access the internet Features: Full speed, auto-sense ADSL routing, bridging Up to 24Mbps down steams and up to 1Mbps upstream data rate Maximum transmission range 6.5 kilometers Friendly GUI for web configuration Compatible with virtually all standard internet applications Support for up to 8 PVCs Port mapping /forwarding and DMZ host network support NAT, IP filtering and password authentication to modem Diagnostic function support DHCP server support Build – in PPPoE support Support SNMP & TR (optional)

Telenet’s TPC 3180 Protocol converter is the most newly promoted Network Bridge that can convert 1-8E1 to 100Base-T or 10Base-T Ethernet, and vice versa. This protocol converter can extend the bandwidth to 16.384Mbps. It not only provide completed indicators to show the status and alarm messages of the E1 line and Ethernet port, but also support BER Stat. of E1 and flow Stat. of Ethernet port. It is widely used in two LAN connecting, remote monitor and video broadcasting Features: Compatible with ITU-T G703, G704 and G823 Support 10Base-T, 100Base-TX protocol 1024 pieces of MAC address list and with address filter function Enable any group of CH1-CH8 E1 channel to transmit the data at will Extend the bandwidth to 16.384Mbps when using 4E1 channels Support auto-inspection of effective E1 channel without interruption of data transfer. Automatically cut off the E1Channel when it has LOS and AIS alarm, and inform the remote end simultaneously. Support remote E1 Loop function 75ohm unbalanced E1 channel impedance RS232 port for management, one software can manage up to 256 pieces of device Internal power supply, AC160V-260V or DC -48V optional   Specification: E1 Port Bit rate: 2.048Mb Line code: HDB3 Standard: in accordance with ITU-T G.703, G.704 Connector: BNC connector, line impedance 75ohm Number of E1: 8 Jitter Performance: compatible with G.742 and G.82 Etherent Port Data Rate: 10/100Mbps Standard: Compatible with IEEE802.3 Connector: RJ45 Number of Ports:1 port Auto-negotiation with half/full duplex

Telenet’s TSW 8008P is the most cost-effective solution to share network for SOHO users. With easy Installation and configuration, this Plug-&-Play super-compact switch instantly provides reliable network with five new and independent bandwidths with the utmost hardware flexibility. In addition, each 10/100Mbps port is equipped with built-in Auto-MDI/MDI-X and Auto-negotiation functions. With the user-friendly and hassle-free features, this switch is designed to reliably meet the diverse performance demands of mid-size network, which do not require management capabilities.   FEATURES Non-blocking Performance Improves Access to Network Resources Eight Independent Bandwidths with 10Mbps – 200Mbps Capability All Ports Support Auto-negotiation and Auto-MDI/MDI-X to Facilitate Installation and Troubleshooting Full Wire Speed Store-and-Forward Technology Instantly Eliminates Bad Packets Support IEEE 802.3x Flow-control for Full-duplex and Back-pressure Flow-Control for Half-duplex. Delicate Plastic Palm Size with an External Power Adapter Support 1K MAC Address Built-in High Efficiency SRAM for Packet Buffer Easy-to-Understand LEDs Display Real-time Traffic Status to Monitor and Diagnose the Network Built-in High Efficiency SRAM for Packet Buffer Broadcast Storm Filter, Runt and CRC Filtering Eliminate Erroneous Packets to Optimize the Network Bandwidth. Support Power Saving Mode by Cable Detection.   Technical Specifications Model TSW 8008P Standards 100BASE-TX,IEEE802.3u 10BASE –T , IEEE 802.3 Ports Eight 100BASE –TX/10BASE-T Media support 10BASE-T category 5TP 10BASE –T category3,4 or 5 TP Connector STP RJ-45 port for TX Bandwidth 100BASE-TX/10BASE-T – 200/100/20/10Mbps,via Auto-Negotiation Duplex modes All ports support half-duplex or full-duplex operation crossover Supports Auto-MDI/MDI-X crossover function LED indictors One LED for power on/off One LED per port for link (green) / activity (blinking ) Input power requirement +9V DC, (0.5A-1A) Power consumption 9W maximum Environment Operating temp :0*C -50*C (32*F -122*F) Storage temp: 20*C – 70*C (-4*F 158*F) Humidity : 10% - 90% RH Certifications FCC part 15 class A,CE class A 159x103x 23mm (6.26 x 4.05 x 0.91 inches )

Telenet's 8-port 10/100Mbps Unmanaged Edge Switch is the latest generation of fast Ethernet switching technology. Eight 10/100Base-TX auto sensing, auto MDI/MDIX ports eases the selection of cable type for devices connectivity and provide a completely flexible high-performance non-blocking full wire speed solution. This switch provides a range of powerful features, delivering reliability and consistent performance for your network traffic. The switch supports standard IEEE 802.3x Flow Control standard which eliminate packet loss in heavy traffic conditions. The Switch uses store-and-forward switching to ensure maximum data integrity. The 10/100 Mbps ports support auto-sensing and auto-negotiation at network speeds. All ports support auto MDI/MDI-X feature, allowing you to connect to workstations, servers, or other switches from any port without the need to change your usual straight-through to twisted-pair cables. The feature of Port Isolation is implemented in this Unit where in the Ethernet Data of the Uplink Port can be transferred to any of the Downlink ports but the individual Downlink ports cannot communicate with each other. This feature is implemented using Port based VLAN.       FEATURES   8-port 10/100Base-TX interface with auto sensing provide a completely flexible high-performance Non-blocking full wire speed solution. The switch supports Max Packet Size of 1536 bytes. The switch supports standard IEEE 802.3x Flow Control to Prevent Packet Loss. Forwarding mechanism – Store and Forward. Port Isolation using Port-based VLAN. Surge Protection on all 8 Ports (Downlink and Uplink ports). Technical Specifications   Ethernet Connector RJ45 Jacks (8 Ports) 10/100Base-TX with Auto-MDIX Uplink : 1-ports PoE Injector (Data + Power OUT) Downlink : 7-ports PoE PD (Data + Power IN BATT Connector Terminal Block PoE IEEE802.3af Standard Not Compliant. Standards IEEE Std. 802.3 10BASE-T 10Mbps, Half/Full Duplex; IEEE Std. 802.3u 100BASE-TX, 10/100Mbps, Half/Full Duplex; IEEE Std. 802.3x Flow control and Back-pressure. Protocols CSMA/CD Technology Store and Forward switching architecture MAC Address 1K MAC addres Network Cable 2-pair UTP/STP Cat 5 cable LEDs Link/Activity per Ethernet port Power: On/Off for Switch Power: On/Off for PoE Injector Power Over Ethernet Injector: Power Supply (IN) for Unmanaged Edge Switch Power over Ethernet 18V @ 30W on Spare Pair (to supply power to the Unmanaged Edge switch as well as a compatible PoE device (e.g. CPE)) No. of Ethernet Ports that can Power ON the Unmanaged Edge Switch Anyone/All of the seven Downlink Ports BATT option Input Voltage : 12V -15V Max Power : 5W Power Over Ethernet Power over Ethernet Injector on Spare Pair of Uplink Port. Injector: Power OUT to external compatible PoE device Voltage : 8V-18V Max Power : 5W Ethernet Devices that can be powered Single CAT-5 Cable Data Lines Pair 1: Pins 1/2 , Pair 2: Pins3/6 CAT-5 Cable Power Lines + VDC: Pins 4/5 , -VDC: Pins 7/8 Power consumption 5 Watt (Edge Switch) 5 Watt (PoE Injector Operating Temperature 0° to 40°C Storage environment 0° to 75°C Operating Humidity 20% to 90% (non-condensing) Dimensions   Environment Std (IP) Dust Protected , Protected from Spray Water upto 60 Degree from Vertical  

Telenet's managed switch is the latest generation of fast Ethernet switching technology. Enhanced by its many, features including port Trucking, VLAN tagging, spanning tree, and broadcast storm filters. Eight 10/100Base-TX auto sensing, auto MDI/MDIX ports provide a completely flexible high-performance non-blocking full wire speed. Solution. The management features include port-based, dynamic and static VLAN, s, GVRP, VLAN tagging, IGMP snooping, port mirroring and port security. Two priority queues per port insure minimum delay for voice over IP or multimedia broadcasting Network management can be accessed via Telenet from anywhere on the network or via a console port at the switch. Power: 110/220V AC. The 10/100Mbps ports supporting auto-sensing and auto-negotiation of network speeds and full/half duplex. These ports can connect to workstations and print servers, giving each a dedicated bandwidth. All ports support auto MDI-II/MDI-X uplink, allowing you to connect to workstations, servers, or other switches from any port without the need to change your usual straight-through to twisted-pair cables. Flow Control to Prevent Packet loss The switch supports standard IEEE 802.3x Flow Control. Working in conjunction with buffer overrun auto detection. This full-duplex data transfer mode provides protection against possible data loss for 802.3x supported servers directly connected to the switch. The advanced features, 802.1p, Diffuser, 802.1x*, IGMP, and 802.1q, facilitate the deployment of applications across an enterprise such as: VOIP, streaming media, and multicast content delivery (IP video conferencing, software deployment).   TECHNICAL SPECIFICATIONS   Physical interface - 10/100 base T (IEEE 802.3) RJ45       SWITCH FEATURE   MAC table size -1024 entries in the MAC table Forwarding mechanism – store and forward Switch fabric -3.2gbps, supporting wire forwarding when all the ports are running at full speed. VLAN groups – up to 64 different VLAN IDs simultaneously can be processed. Support port mirroring / port security Auto MDI-MDIX Light console management  

Telenet 8-port 10/100 Mbps managed edge switch is the latest generation of the fast Ethernet switching technology. The switch store and forwarding switching to ensure maximum data integrity the switch support auto sensing auto-negotiations and IEEE 802.3x flow control standard which eliminate packet loss in heavy traffic conditions. All port also support auto MDI/MDI-X feature eases the selection of cable type devices connectivity and provide a completely flexible high-performance non-blocking full wire speed solution the management features include port base, tagged base VLAN,s per port bandwidth restriction via rate limiting and port security. Out of this port, the last port is configure as uplink port and remaining port are downlink ports the feature of port isolation is implemented in this unit is where Ethernet data of the uplink port can be transferred to any of the downlink port but individual downlink port cannot communicate with each other. Additional feature of the rate limit and broadcast storm also are present With its unit-in remote management capability, the switch offers an easy-to-use platform-independent management of monitoring. For text-based management, the switch can also be accessed via telnet and console port for configuration and monitoring.   Feature: 8-port 10/100 base-TX interface with auto sensing provide the completely flexible high-performance non-blocking full wire speed solution. Support auto-negotiation for speed and duplex mode. Support auto-MDIX for each port The switch supports max packet size of 1536 bytes The switch support standard IEEE 803.2X flow control to prevent packet loss. Forwarding mechanism – store and foreword Port isolation using port-base VLAN Port security IEEE 802.1Q tagging VLAN Support bandwidth control – form 128k up to full (100 mbps) Support broadcast storm control Management via telnet, web management, and console port DHCP option 82 IGMP for multicasting

Telenet’s 8 Port Gigabit Port Isolation Switch, TSW1108W provides 8 10/100/1000Mbps RJ45 ports. All RJ45 ports support Auto-MDI/MDIX function. It provides a simple, economical, high performance, seamless solution to upgrade to 1000M networking connection. It provides one “VLAN” switch, the switch is off at default, and at this state the switch can be used as a normal 8 ports gigabit switch. When switch on the “VLAN” switch, every port can communicate with the uplink port, and the other ports are separate with each other except the uplink port. The port 8 is default as the uplink port. It provides a simple, economical, high performance and flexible solution for your networking construction   Feature: Complies with IEEE802.3, IEEE 802.3u and IEEE802.3ab standard Adopts IEEE802.3x for full duplex and Backpressure for half duplex 8 10/100/1000Mbps auto-negotiation RJ-45 ports (Auto MDI/MDIX) Adopts store-forward technology, providing full wire-speed to assure integrity of data Supports Jumbo Frame transmission MAC address auto-learning and auto-aging Independent bandwidth for each port, and real non-blocking data transfer Realize port isolation with just one VLAN,s switch 12 V DC power supply Sleek desktop metal case Forward and Filter Rate 10Mbps：14880pps 100Mbps：148800pps 1000Mbps：1488000pps LED Indication      Link/Act                                  Other Link/Act Power Dimension (L×W×H) 230×147×40mm Environment Operation Temperature：0ºC-40º No. of Ethernet Devices that can be powered Single Input Input：12V DC