Gate & Sluice Valves Dealers in Andheri, Mumbai

We are the eminent Gate Valves Manufacturer and Exporter in India which is basically a motor valve. It is very useful and made with advanced technology. Features: Optimum quality Low maintenance required Economic prices

We are offering pressure regulating valve. Miniature series | service : air water sizes: 3 mm & 6 mm (g 18" & g14") flow: up to 22 scfm @ 7 kg cm2g regulator compact design high performance

We are a well-known manufacturers and suppliers of a vast array of Valves and we are offering of Safety Valves.

Gate Valves are provided with properly machined and lapped backseat to ensure re-packing under pressure while fully open. Availability of Solid Wedge, Flexible Wedge, Split Wedge and Parallel Wedge designs offer maximum option to clients for suitable selection.Gaskets and Gland packing material are selected to suit service conditions like temperature, corrosion, erosion, pressure, vacuum and other applications.

Safety valves available for most applications such as steam, air, vapour & liquids. Valves are designed to meet the requirements of applicable a.s.m.e & api codes.

Valve consists of a body and shut off mechanism inside the body. Body has through axial holes of different diameters over the length. Lower part the hole is 8 mm in dia, the remaining part is of 22 mmin dia. (MOC – SS). The upper part of the body is provided with female thread for securing stem assembly and male thread for fastening the valveon the bottle. From one side and under the body there is a connection with male threads for attaching to the pipe lines. The shut off mechanism consist of valve assembly with a pad made of polyamide resin, stem assembly (MOC - MS), bushing (MOC – Gun Metal), gasket (MOC - Copper), spring (MOC – Case hardened steel) with packing . The stem assembly in its turn has a nut, stem, ball and pivot journal. Hand wheel assembly is fixed by nut on the square end of stem for opening and closing of the valve. The air leakage from the valve is prevented by a seal and made in movable and fixed joint. The movable joint of valve end and bushing are sealed by rubber rings. Valve assemblies have tested for the leak tightness by compressed air at a pressure of 400 kgf/cm² and hydraulic test for strength at a hydraulic pressure of 600 kgf/cm².

We supply Pressure Relief Valves to our clients which are well in demand and have important application in various fields. It is a kind of safety device that relieves overpressure in a vessel or piping. We have a comprehensive range of these Pressure Relief Valves that are available at reasonable prices and are timely delivered to our clients. Applications : To relieve pressures through pipes, hosing, tubes or entire system

Amarama Engineers designs & manufactures spring loaded Pressure Safety Relief Valves which are installed to release the excess pressure developed in a system like reactor vessels, pipelines due to a chemical reaction, thermal expansion etc. Our full bore inlet design gives quick release of pressure and faster shut off on the return. Through our years of experience we have categorised our range of springs for different pressure and sizes of valves. The flexibility in our design helps us cater to different applications like corrosive vessels, utility, high pressure, temperature, hydrogenation, reactor jacket, bitumen blending & many more applications. For example, for corrosive we provide PTFE lined inlet nozzle and Hastelloy �C� plug, which ensures leakage class 6. We also assist our customers with the sizing and selection of Pressure Safety Relief Valves according to API 521.

We manufacture and export grade Forged Steel Bellow Seal Gate Valves S/W with complimentary accessories. It has won critical acclaims for its technically engineered structure. Technical DataValve Designed to BS-5352 (Reduced Bore)Valve Tested to API- 598 / BS- 5146Socket Weld Ends to ANSI-B-16.11Butt Weld Ends to ANSI-B-16.25Screwed Ends to ANSI-B-1.20.1 (NPT)End to End as per Manufacturers SpecAccessoriesHand Wheel Locking ArrangementActuator Mounted ValveNotesValve upto 50mm NB are from ForgingOptional Full port Design upto 40mm NBAlso Manufatured in Grade F 304L / F 316LOptional Stellited Seat & PlugOptional Screwed Ends Optional Butt Weld EndsOptional Socket Weld EndsAlternate Bellow Material= HC-276/ Inconel-625

• Material: Mild Steel
• Surface Finish: Zinc Plated
• High Frequency: 50 Hz
• Type: Pneumatic
• Packaging Type: Box
• Tensile Strength: 400 Mpa

GATE VALVES : WESMEC Brand Gate valves offers a comprehensive range of Gate Valves. For the past decades our customers worldwide have trusted us to provide them with consistent and reliable valve products in their most severe and critical service. Gate Valve are designed to operate fully open or closed. Because they operate slowly they prevent fluid hammer which is detrimental to piping systems. There is very little pressure loss through gate valve. In the fully closed position, gate valves provide a positive seal under pressure.   FEATURES: • Available in a variety of end connections. • Available in Stainless Steel Spiral wound and Asbestos Graphite gasket for more safety. • Various types of Coating used to avoid corrosion. • Hydraulic Test Pressure: (BODY) up to 210 Kg/Cm². • Hydraulic Test Pressure: (SEAT) up to 150 Kg/Cm². • Pneumatic Test Pressure: up to 10 Kg/Cm². • Non Destructive Test (NDT) available on request.   Standards Followed: • ASME B16.34/ B16.11/B1.20.1, BS 1873, API 602, ISO 15761, CE Marking. • Marking and Identification of Valves as per MSS-SP-25.   • Application: It is primarily used for on-off conditions or for isolation.

Pressure Reducing Valves protect household water installations for industrial or commercial applications within the range of their specification. By installing a pressure reducing valve, pressurisation damage is avoided and water consumption is reduced. The set pressure is also maintained constant even when there is wide inlet pressure fluctuation. Reduction of the operating pressure and maintaining it at a constant level minimizes flow noise in the installation.  Spring loaded pressure reducing valves operate by means of a force equalising system. The force of a diaphragm operates against the force of an adjustment spring. If the outlet pressure & therefore diaphragm force fall because water is drawn, the then greater force of the spring causes the valve to open. The outlet pressure then increases until the force between the diaphragm & the spring are equal again. The inlet pressure has no influence in either opening or closing of the valve. Because of this, inlet pressure fluctuation does not influence the outlet pressure.

• Hydraulic oil, Water, Steam, Gas, Chemicals.: CS zinc plated and dichromated/Stainless steel/Brass in natural finish

We have wide range of square body ball valves in Carbon steel, Stainless Steel and Brass. Sizes from ¼” to 2” are available ex-stock with us. Large sizes can be custom made as per your needs. Pressure ranges from 1,000 PSI to 10,000 PSI. Our range includes 2-way, 3-way and 4-ways designs. Our Ball valves are available in a variety of end connections and also include flange end connections from 1.5” and above which conform to SAE and CETOP standards. Standard valves come with Buna or Viton seal but we can offer Teflon seals as well.

• Brand: ksb
• Automation Grade: Manual
• Is It ISO Certified: ISO Certified
• I deal in: New Only
• Rust Resistant: Yes
• Features: Rugged construction, Hassle-free installation

• STEP 1: Select the hydraulic cylinder that best suits the application.
• STEP 2: Select the series of hydraulic pump with adequate oil output and reservoir capacity to power cylinder.
• STEP 3: Select pump within series with the valve option that best matches cylinder, pump and application.  

CONSIDERATIONS: Will the valve be used with single or double-acting cylinder? Will the valve be mounted on the pump, away from the pump or directly into the hydraulic lines? Will the valve be manually operated or is remote control preferred? Is independent control of multiple cylinders, or hydraulic tools preferred? What directional control and pressure control valve functions are needed for the application?   Basic valve types include manually operated, air or solenoid operated and pilot operated. Special application valves for pre-stressing and post-tensioning are also offered. IN-LINE HYDRAULIC VALVES Load Lowering Valve - Provides precision metering for controlled return of the cylinder pistion.   Sequence Valve - Used when a cylinder in a multiple cylinder application must advance before any other.   Pressure Reducing Valve - Permits independent pressure control to two or more clamping systems operated by a single power source.   Shut-off Valve - For fine metering of hydraulic oil. Several may be used to control multiple single-acting cylinders.   Check Valve - Permits flow of hydraulic oil in one direction only.   Pressure Relief Valve - Used at remote location in a hydraulic circuit where maximum pressure requirements are less than the setting of the basic overload valve in the pump. Protects a hydraulic system against over pressurization.   Metering Valve - Restricts surges by restricting flow to a certain level; when flow subsides, valve reopens automatically. For systems using large cylinders or extended lengths of hose.   Pressure Regulator Valve - Permits external adjustment of operating pressures at various values below the internal relief valve setting of the pump.

Safety Relief Valves, Slab Type Gate Valve, Mini Ball Valve

Gate Valve, Ball Valve, Piston Valve, Plug Valve, Balancing Valve

• Size: 3" to 20"

PRDS used in turbine bypass applications help to protect the turbine during start-up, power trip and also for part load generation. Turbine by pass valve prevent venting of steam into atmosphere and allow the steam to be dumped into condenser, so that energy can be saved to generate high temperature Boiler Feed Water.

Material : ASTM Specifications Carbon Steel, Alloy Steel, Stainless Steel, Duplex Stainless Steel, Super Duplex Stainless Steel, any other special material,Trims ,Varieties of combinations