Z Cross International Dombivali, Mumbai, Maharashtra

DESCRIPTION ZC-SEALTITE is an aqueous Co-polymer emulsion specially formulated for use with cement.  ZC-SEALTITE modifies the property of cement in mortars and in concrete to make them  perform better in terms of water proofing, repair, corrosion inhibition, bonding, durability and wear resistance .   PRIMARY USES Corrosion protection of steel. Floor screed and topping. Concrete and floor screed repairs. Water proofing and tanking of basements. Bonding old concrete to new concrete.   ADVANTAGES Water resistant, excellent adhesion to concrete, steel, brick, stones, compatible with cement. High compressive, tensile and flexural strength. Resistant to ingress of salts, mineral oils etc. Non toxic. Suitable foruse in potable water tanks. Excellent corrosion protection. Economical when compared with epoxy mortars.   TYPICAL APPLICATONS Corrosion Repairs of Beams, Columns and Slabs: Industrial Floor or Floor Duct Nosing Repair: Bonding old Concrete to New Concrete: Plaster & Screed Mortars:

Type : Liquid

Purity : 100%

Elastomeric Coating provides a long-lastingWaterproof Coating Exterior masonry walls—particularly ones that are weathered—have long represented one of the most difficult maintenance challenges for the contractor, the painter, and the waterproofer alike.   Most typical exterior surfaces can be successfully protected and maintained by the regular applications of high quality conventional acrylic latex paints. But even the best paints often tend to split and fail when they have been applied over the surface cracks that develop as masonry ages   A Better Alternative: Elastomeric Wall Coatings  The construction chemical industry has known about the limitations of traditional paints on masonry. For almost that long, the industry has been searching for better alternatives. Early attempts to solve the cracking problem, involved formulating coatings with polymers not generally used in conventional paints. Many of these experimental systems provided acceptable service as dirt-resistant coatings.   Unfortunately, virtually all of the polymers tested formed hard films that were too rigid to accommodate the temperature-related fluctuation in the dimensions of the cracks. Inevitably, coatings based on these hard polymers fractured, exposing the masonry to the elements once again.   Recognizing that hard binders were not the answer, the industry turned to "softer'' polymers with much lower glass transition temperatures. Many of the products investigated were already seeing use as binders for caulks and sealants. Because they had low glass transition temperatures, they furnished excellent elasticity and flexibility over a wide range of temperatures.   ADVANTAGES: Instead of depending on a separate, external component to impart flexibility to the film, 100% acrylic elastomeric polymers derive elasticity from a unique combination of special composition, molecular weight, and crosslinking. As a result, they retain flexibility over periods of time. Moreover, formulations based on the 100% acrylic elastomeric polymers exhibit their elastomeric properties over a broad range of temperatures. Thus, the performance of waterborne coatings based on the acrylic elastomerics remains consistently outstanding under all conditions.   In comparing the different types of binders in other areas of performance, the 100% acrylic binders have a significant edge over styrenated products in the area of ultraviolet stabiiity, over viny! acetate products in the area of hydrolysis resistance, and over both chemistries in the area of dirt pick-up resistance. As a result, on extended exposure, waterborne acrylic coatings are more resistant to chalking and do not yellow as do styrenated products. They are not as vulnerable to damage from ambient moisture as acetate-based systems, and they remain cleaner than both types of non-acrylic systems.   Protection with Decoration & Waterproof Elastomeric Exterior Coating ZC-SEALCOAT is a unique polymer based waterproofing, elastomeric exterior performance coating to protect the concrete structure from degradation in varied climatic conditions. ZC- SEALCOAT is a single component 'Ready to Use' formulation with quick drying properties at room temperature. Its outstanding properties of water repellency coupled with toughness helps to arrest the leakage  during rainy season while its stability against UV radiation keeps the brightness unfazed for years together. Its Two in One performance protects the surface from water seepage & leakage, enhances life of plaster and provides desired aesthetical outlook.   PERFORMANCE FEATURES:- Excellent Water Repellency Resistance to U.V. Radiation Resistance to Fungus and moss. No peel-off tendency Tough and Scratch-proof. Excellent Brightness and finish. Stable at high temperatures. Single component, ready to use system Quick drying at room temperature. No water curing required. Can be pigmented in wide colour range   OTHER SALIENT FEATURES WATER REPELLENT WATER VAPOUR PERMEABLE FUNGUS RESISTANT UV RESISTANT CO diffusion resistant Environment friendly Excellent crack bridging Aesthetic Decoration Cost Effective Covering Capacity   DIRECTIONS FOR USE Surface Preparation : Remove dust, dirt, grease, loose particles, flaking paint, wax, fungus, algae from surface using wire brush. Surface should be washed with water and allowed to dry. Priming : Apply the priming coat using recommended primer or by mixing ZC-SEALCOAT with water in the ratio of 1:2 using brush. Finishing : Finish the surface by applying 2 coats of ZC-SEALCOAT with an intercoat interval of 4 hours. Thinning : ZC-SEALCOAT is ready to apply paint, which does not require thinning. Storage : Keep container closed with a tight lid when not in use. Store in dry place.

Form : Liquid

Speciality : Waterproof

Color : White

Packaging Type : Paper Packet, Plastic Bag, Plastic Bucket, Plastic Packet

Feature : Long Shelf Life, Super Smooth Finish, Unmatched Quality, Weather Proof

Packaging Size : 5-10 kg,10-15 kg,15-20 kg,20-25 kg

State : Powder,Liquid

Application : Interior,Exterior

Color : White,Blue,Green,Purple

Packaging Type : Plastic Bags,Buckets,HDPE Drums,Plastic Drums

Purity : 100%

Feature : It is easily remove stains of gutka and tobacco from printed wall.

Form : Liquid

Z CROSS ACRYLIC PASTE PUTTY Wall Plastering has never been so easy, so in order to overcome this difficulty ZCROSS has introduced ZCROSS ACRYLIC PASTE PUTTY, ZCROSS ACRYLIC PASTE PUTTY is the ready mixed wall putty that gives your walls super smooth finish and which is faster than other ordinary putty.It is faster to prepare, apply, dry and faster to paint. It is pre-prepared and easy to apply. Being ACRYLIC based it is Primer FREE.   packing available: 20kg Bag   ZCROSS ACRYLIC POWDER PUTTY ZCROSS ACRYLIC POWDER PUTTY is the wall putty in the powder form that gives your walls super smooth finish. It is faster to prepare, apply, dry and paint. Being ACRYLIC based it is Primer FREE. Pioneer powder putty is a perfect blend of natural minerals provided by the mother earth. It is used to application on different types of surfaces to get the smooth Pure White finishes.   Packing available: 1kg, 5kg, 20kg and 40kg Bag   Z CROSS ACRYLIC PASTE PUTTY Wall Plastering has never been so easy, so in order to overcome this difficulty ZCROSS has introduced ZCROSS ACRYLIC PASTE PUTTY, ZCROSS ACRYLIC PASTE PUTTY is the ready mixed wall putty that gives your walls super smooth finish and which is faster than other ordinary putty.It is faster to prepare, apply, dry and faster to paint. It is pre-prepared and easy to apply. Being ACRYLIC based it is Primer FREE.   Grades available: MF and SF Packing available: 1kg, 5kg, 20kg, 30kg and 40kg bag

Type : Wall Putty

Color : White

Packaging Type : Plastic Bag

Form : Powder

Feature : Long Shelf Life, Super Smooth Finish

APPLICATION Single multifunctional product for dispersing & leveling of dispersing dyes. On substrate plysters fibers,yarns and fabrics   CHEMISTRY FOR PERFORMANCE Excellent despersing, migration and leveling properties for all class of despires dyes. Better brilliancy,gastness and softer feel.   CHEMISTRY FOR ECONOMICS  Low does level.

Form : Liquid

Purity : 100%

Color : Available in Many Colors

ZCROSS'S TILE ADHESIVE ZCROSS Tile Adhesive is a ceramic tile adhesive. It is a pre-packed cementitous tile adhesive which ensures an excellent bond on concrete, plastered and even ceramic and mosaic tile surfaces. Pioneer Tile Adhesive ensures perfect Water tightness.   Packing available: 10kg and 20kg bag   ZCROSS INTERNATIONAL We are pleased to introduce ourselves as manufactures of Water-Based paints like Textures, Acrylic Putty, Cement Putty, Distemper, Primer, Interior and Exterior acrylic paint, tec. We also deal in Textile chemicals and other speciality chemicals and other specially chemicals. At Zcross we have an experience of 33 years and our operations are spread over 6,000 sq.ft. area with sufficient power and other facilities. We have a dedicated team of labour and technician for purchase of raw materials, quality control, delievery and marketing. We always look for better method of manufacturing and better solution for complicated paint manufacturing. In the bussiness of manufacturing Water-Based pints, we believe in quality and customer satisfaction. We have a capacity of 8 to 10 ton manufacturing per day for texture. We are in the process of expansion for the same. We undertake bulk operations and specialized in undertaking corporate offers to cater the needs of different companies. Our sole aim is to provide exquisite and reliable quality of products that cater to the modern needs.

Application : Tiles Use

Feature : Heat Resistant

Application : Tile Fixing

TERRACE / ROOF WATERPROOFING BASED ON MEMBRANE COATING SYSTEM ZC-ROOF GFM is designed to protect surface of the building terrace & roof from water & weathering effect.   It is developed for complex/critical applications where conventional waterproofing/ weatherproofing products cannot be used or applied. In these areas waterproofing products like polymer admixtures, repellent, adhesives, general purpose coating and sealants do not perform effectively for long time. In such applications the product should withstand heat, UV effects, expansion & contraction, gravity settlements, shrinkage and ageing effects. The product should be long lasting & should remain elastomeric and active permanently.   Applications Substrates material : Cementitious substrates, asbestos cement, insulation materials, metal substrates, wood & plywood, bricks & stones, slates & tiles, plastics, bituminous coatings, paints, mastics, asphalt & felt.   Substrate/structure types : Concrete/plastered roofs & walls, corrugated sheets, terrace gardens, parapets & chhajjas, drain sections, expansion joints, ventilation outlets, J hooks & screw overlaps, lighting fixture mountings, roofing junctions   Type of construction : Residential buildings, commercial buildings, Manufacturing units, malls, warehouses, nuclear power structures, theatres.   Components of the System : ZC-Sealcoat :Acrylic based elastomeric high performance coating emulsion. It is single component and ready to use formulation with quick drying properties. It is water repellent with toughness to arrest leakage and seepage of water. It protects the surface of UV radiation. It has got excellent adhesion to substrate and elongation of 200%. It has very good impact strength and withstands extreme temperature. ZC-ROOF GFM :ZC-ROOF GFM (Glass fibre matt ) is supplied by Owens Corning India Ltd. and it is made of glass fibre chopped strands. It is incorporated in this system because if the treated surface has foot traffic then plastic coating alone may not withstand the ware and tare. On the surface where no foot traffic incurs the ZC-ROOF GFM need not be applied. However it is strongly recommended to use ZC-ROOF GFM for long lasting effectiveness and toughness. ZC-Elastofalt : ZC-Elastofalt is a thixotropic cold applied polymer modified bituminous coating. It has very high adhesion strength. It protects the surface from water & weathering effects. The elongation is 900% and forms very good film on the substrate. It can be applied on any surface except ceramic tiles & metal. ZC-Elastoprime:ZC- Elastoprime is a primer or bond coat for surfaces like tiles or china mosaic chips. ZC-Elastofalt or ZC-Sealcoat do not easily adhere to the substrate like tiles or china mosaic chips. On such substrate it is essential to give bond coat of ZC-Elastoprime, which is actually ZC-Elastofalt diluted with water in the ratio 1:1.   Surface Preparation Surface should be clean & dry. All the surface lying water, mould growths, moss or other vegetation, loose debris etc. should be removed prior to application. Ensure that surface is free from visible dampness, dust. Dirt and other form of contamination should be removed prior to application.   Advantages Single component, multiplayer, solvent free Can be applied to different type of substrate No strong odour or toxic fume Fast curing & drying High tensile & elongation strength Permanently elastomeric and ageing proof Application by brush/roller/spray Absorbs rainfall sound   Benefits Ready to use, simple application Long lasting realiability Does not crack or brittle UV/Heat resistance Crack bridging capability Traffic resistance Resistance to algae growth Reduces sound transmission

Purity : 100%

Uses For waterproofing of: New roofs. Balconies, terraces, parking garages, asbestos and concrete roofs. Industrial washrooms & shower Water reservoirs and swimming pools. Foundations, cellar walls, retaining walls, bridges abutments. Refurbishing of old waterproofing system including torch-on membrane. Facade damp proofing. Water proofing/Curing membrane and protective coating for sub structure.   Features Single component and cold applied. ZC- ELASTOFALT has excellent UV resistance and long term ageing stability. Cured membranes from ZC- ELASTOFALT remain highly flexible even at extremes of temperatures (-25°C to 120°C). Excellent vapour barrier. Easy to use. Non-flammable and Non-toxic Environment friendly. Resistant to chlorides and sulphates commonly present in the soil. Compatible with cementatious tiling adhesive.   Surface Preparation All surfaces should be sound, clean and free of contaminants. Absorbent surfaces e.g. concrete should preferably be dampened with water. In kitchens, toilets and other wet areas all the openings should be properly sealed. On all weak points such as cracks or around the pipes use a woven fibre glass mesh as reinforcement between the two coats of ZC- ELASTOFALT   Application ZC- ELASTOFALT can be applied by brush, roller or squeegee. Hot, dry or very porous substrate should be dampened with clean water prior to application of ZC- ELASTOFALT. When two or more coats are required, ensure that the preceding coat is fully dry before applying the successive coat, which should b e applied at right angle to proceeding coat. ZC- ELASTOFALT also acts as a non-degradable curing membrane; hence it may be applied immediately after the removal of mould, to the concrete structure, which has no aesthetic value such as the sub structure of the building.

Application : Construction Use

Feature : Long Life

Application Strong, sound-reducing, installer-friendly soy adhesives for flooring installations. This adhesives chemically modified to produce strong, heat resistant bonds when adhering paper substrates Improved properties in wood bonding through.

Type : Liquid Glue

Application : Industrial

Type : Herbal

Feature : Gives Shining

Form : Liquid

Color : White

Application : Industrials,Paints,Gift Item,Show Piece

Material : Polyester,Epoxy

Application Whenever you use waterproof Plywood, you need to use Waterproof Adhesive also otherwise the laminate starts de-bonding after some time. Waterproof Ply or Adhesive, both are not only waterproof and stronger than standard Ply or adhesive but costlier too. So people restrict it to only to water prone areas High-quality concrete pouring plate in plywood. Logs for plywood construction in a plywood factory.

Application : Woodworking

Feature : Eco Friendly

Form : Liquid

ZCROSS CRACK REPAIR ZCROSS Crack Repair is highly flexible, asbestos free, high solid filler for major and minor cracks. It is white cement based crack filler specially developed to fill cracks in plastered surfaces. It contains finest grades of cement, sand, selected fillers and best quality polymers to give it unique properties.   The materials should be used only to fill shrinkage cracks and other small cracks in plaster. Zcross saves time and makes labour's work faster. This should not be used to fill structural cracks and construction joints. It is available in powder form.   Packing available: 1kg, 5kg and 20kg bag

Purity : 99%

ZCROSS ACRYLIC DISTEMPER ZCROSS ACRYLIC DISTEMPER is water based, interior wall paint and gives wall a delightful, attractive, matt finish that last for ages. It is an economical interior coating. It is a tested formulation with acrylic co-polymer binder, its special formulation ensures shade retention for a long time and its fast drying property facilities quicker completion of painting jobs. Acrylic distemper dries within 2-3 hours and therefore successive coats can be applied in quick time.   Packing available: 2kg, 5kg, 10kg and 20kg container   Z CROSS'S CLASSIC GOLD DISTEMPER ZCROSS CLASSIC GOLD PREMIUM DISTEMPER is water-based, interior wall paint and gives walls a delightful, attractive, matt finish that lasts for ages. It gives as excellent, clean, and quick drying and a perfect finish. It is a tested formulation with acrylic co-polymer binder, its special formulation ensures shade retention for a long time and its fast drying property facilitates quicker completion of painting jobs. Classic Gold Premium Distemper dries within 2-3 hours and therefore successive coats can be applied in quick time.   Packing available: 2kg, 5kg, 10kg and 20kg container   CLASSIC PLASTIC EMULSION ZCROSS'S CLASSIC PLASTIC EMULSION gives a smooth and Matt finish to the wall. A perfect buy if you have been using distemper till now. It is a premium quality, more durable and has long lasting finish. ZCROSS Plastic Emulsion is made up of top quality acrylic co-polymers, which not just gives it is superior finish and excellent coverage, but a soft silky finish.   Packing available: 1ltr, 4ltr, 10ltr and 20ltr container

Type : Distemper Paint

Color : Blue, Copper, Multicolor, Pink, Etc.

State : Liquid

Application : Interior Use

Application : Brush, Roller, Spray Gun

Finish : High Gloss, Soft Sheen

ZCROSS NATURA TEXTURE Natura textures are co-polymer based finishing for beautifying and protecting concrete structures. NATURA Textures draws inspirations from nature and transforms these exciting textures to your walls, homes and lives. It is recommended for exterior as well as interior application. NATURA Texture being water repellent, fire resistant and flexible gives better outlook with various designs along with infinte colour combination. NATURA Textures are not only simple and decorative, but also highly durable and can withstand any demotic conditions.   Packing available: 5kg and 25kg bag/container   ZCROSS WATER BASED PRIMER ZCROSS WATER BASED PRIMER is premium acrylic primer made from cross linking polymers. It can be used for both exterior as well as interior applicable. It reduces the porosity of the surface and therefore increases the coverage of the paint. ZCROSS Water Based Primer gives a soft feel to the surface and reduces the porosity. It also protects the wall from any anti fungal and algae resistant.   Packing available: 1ltr, 4ltr, 10ltr and 20ltr container   ZCROSS CEMENTO PLAST ZCROSS Cemento Plast is a perfect blend of white cement, high performance polymer, specific additives and mineral powder designed to obtain a fine and durable subsurface to receive all kinds of decorative paints. It can replace conventional Plaster of Paris (POP), Putty and Gypsum applications. ZCROSS Cemento Plast overcomes the shortcomings of conventional putty like firm rigidity and water sensitivity.   Packing available: 25kg, 40kg

Finish : High Gloss

Nature : Aqueous acrylic/styrene copolymer dispersion   Application : Application : ZC-CHEMCRYL-295 is used for the production of high- gloss to matt indoor and outdoor coatings for application on plaster, masonry, asbestos cement, concrete, wood, and other substrates. Moreover, ZC-CHEMCRYL-295 is used as an impregnating agent, primer, binder for textured finishes, base material for producing pasty construction adhesives ceramic tile adhesives, and as an additive for hydraulic binders.   Storage : When kept in tightly closed containers in a cool but frost free place, ZC-CHEMCRYL-295 can be stored for 12 months.

Color : Blue, Orange, White, Etc.

Application : Painting Use

Application : Brush, Roller

Finish : High Gloss

Other Names : Wall Coatings

Highlights Excellent Dispering & Complexing Property Ha Sim,Prove Color Yeild, Levelness And Fastness Of The Cellulose Dying Specially With Reactive. Useful For Exhaust As Well As For Pad Liquors.Cleanses Roll During Silicate Padding. Reproduciblity Of Dying Is Very Good When Is Using In Routing Dying Operation. Reproduciblity Of Dying Is Very Good When Is Using In Routing Dying Operation. Is Non Foaming. Superior Remove Of Unfixed / Hydrolised Dyes In All Cases I.E Batch And Continuous Operation; Dyed And Printed Goods. Help In Avoiding "Tinting" Of Greond Of Printed/Yam Dyed Good I.E Anti-Tining Agent. Good Proctective Colloid ,Help Dyeing And Washing Off Even In Hard Water Condition Help Remove Gums Silicate Etc Of Printed/Padded Goods,Thus Improving The Handle Of The Threated Material. Useful Even Paraoxide Bleachbath For Demineralising & Stable Dispersions Compactible With Ionic And Nn-Ionic Product.   Application 0.3-0.4% ZCROSS FBSN in peroxide bleach bath. 0.2-0.4% ZCROSS FBSN in dye bath. 0.5-1.0% ZCROSS FBSN for washing of in batch process. e.g soft flow cabinates,chees. 1-2gpl ZCROSS FBSN for washing of operation on jiggers and continuous soaper path i.g open width woven fabrics(dyes/printed).

Use : For Textile Processing

Pacakaging : Plastic Bottle

Application : that can remove grease , resins, varnish ,paint ,adhesive etc

Type : Skin Friendly

Feature : It is solvent , acid free, non-toxic and non-abrasive

Form : Liquid

Packaging Type : Plastic Bottle

Form : Liquid

Packaging Size : 1ltr, 500ml

Packaging Type : Bottle

SAFARI EXTERIOR EMULSION ZCROSS'S Safari Exterior Emulsion is water based exterior wall finish suitable for dry to moderately humid climatic conditions. Safari Exterior Emulsion gives neat and clean shades that do not fade and last longer than cement paint shades. Currently it is available in white and different light shades.   Packing available: 1ltr,4ltr,10ltr and 20 ltr container   SAFARI 100% EXTERIOR EMULSION ZCROSS'S Safari 100% Acrylic Exterior Emulsion is a water-based 100% acrylic, exterior wall finish, a high performance, long lasting exterior paint specially designed to resist saponification, U.V. degradation, etc. It also provides protection against any algae of fungal growth. It is a high sheen product.   Packing available: 1ltr, 4ltr, 10ltr and 20ltr container.

Color : Blue, Copper, Multicolor, Orange, Pink, Etc.

State : Liquid

Application : Painting Use

Application : Brush, Roller

Packaging Type : Can

Finish : High Gloss