Mega Power Solar Butibori, Nagpur, Maharashtra

Non - pressure solar water heater Non-pressure solar water heater is a kind of compact system of solar collector and water storage tank. The whole system relies on the different density of cold water and hot water, thus Non-pressure solar water heater also called thermo-siphon solar water heater. The system can work without the circulation pump and no heat pipe connection. Cold water directly filled into the vacuum tubes, the vacuum tubes gather energy and heat the cold water, the lighter hot water tank and cold water come down then be reheated.   That is how the water does circulation by itself. Please see (fig.1) for its working principle. Non-pressure solar water heater system is most economical and suitable product for low latitude countries and regions, especially for Asian, India, Africa, Oceania, South America and South part of North America. Optional accessories: controller and electrical heater.   Product model: i. ECO; ii. AT; iii. EVERHOT Vacuum tube: Ø47-1500mm, Ø58-1800mm co-axial structure high borosilicate 3.3 glass vacuum tube. Inner tank material: SS304 L (Low Carbon)-2B (Food Grade)Stainless Steel (SAIL/ JINDAL make only) Outer tank material: Color powder coating steel / Stainless steel/ Precoated Galvanized (JINDAL/ UTTAM GALVA). Frame : Galvanized steel plate with thickness of 1.5mm; MS powder coated 1.5mm thickness. Frame angle : 250, 380 or 450 Capacity of water tank: 98L ~ 288L. Heat preservation layer: high pressure automatic polyurethane foaming layer with thickness of 50mm to 55mm. Heat preservation : 72 hours. Hailstone resistance: Dia≤25mm.

A “grid-tie SPV system” (sometimes referred as utility/grid interactive or On-Grid) is the one working in synchronization with EB grid and pushing electricity into the grid. That result in net energy drawn from the grid is reduced to an extent of solar PV energy generation. This is the simplest and most cost effective PV design for most of the sites where power is reliable and stable. Because of the very fact that these systems are tied into the grid, it follows the safety feature of disconnecting the system from the grid when grid goes down. The system does not provide backup power during a power cuts (even if the sun is shining). But for the sites with reliable grid power and the day time usage are high, this is usually logical and economically viable system choice. Additionally, the can be synchronized with DG when the load is higher than the PV generation.

PL-11-B-11-L-WXOA 48x0.7W LED 24V DC 115(W)x14(D)mm Power: 42W

PL-11-F-L-WXOA 12x1W LED 48-72V DC 273(L)x193(W)x35(H) Power: 15W

Occupancy Sensor PN-11-D-L-WXOA 230V AC 126.7(f)x71.2(D) mm

PF-11-D-L-WXOC 16x2/24x2W LED 230V AC Without Lens 160/190(ø)x150(D) mm Power: 40/60W

MEGAPOWER solar assists variety of Original Equipment Manufacturers (OEMs) in various ways Research & Development of Product Outsourcing (supply) of Solar system, solar equipment, solar components and parts Sales and distribution of Solar products

PD-11-D-L-1XOA 3x1W/5x1W LED 230V AC 15°/25°/45° Lens 90(f)x165(H) mm Power: 5/7W

Precision die-cast/deep drawn stainless steel enclosure High quality toughened glass diffuser Dimming optional RGB synchronous color changing system IP-68 PD-13-A-L-1XOA 6x1W/9x1/3R+3G+3BW LED 12V DC 8°/15°/25°/45°/60° Lens 144(ø)x95(H) mm Cut out: 120(ø) mm Power: 8.5/12/13W

Slim profile ideal for concealed lighting T8 rods also available T5 & T8 integrated fitting available PC-14-D-L-WXOA(T8) 96x0.2W (With Fitting) 230V AC 1200mm (L) Power: 19W

PB-11-D-L-1XOA 3x1W LED 220V AC 8°/15°/25°/45°/60° Lens 90(f)x18(D) mm Cut Out: 75(f) mm Power: 5W

PE-12-D-L-WXOA 12x0.2 LED 230V AC 80(W)x80(H)x30(D) mm Cutout: 65x65 Power: 5W

Power efficiency > 74 % (above 3W) Power Factor > 0.9 (above 6W) Die-Cast aluminium housing High quality toughened glass diffuser IP-65 PD-14-P-L-1XOB 5x1W/3x3in1RGB LED 230V AC/12V DC (RGB) 8°/15°/25°/45°/60° Lens 85(ø)x110(D)x175(H) mm Power: 7/6.5W(Avg.)

  Power efficiency > 80 % Power factor > 0.9 Die-Cast aluminium housing Optimum thermal management Short circuit & open circuit Protection on driver IP-66 PE-11-D-L-WXOA 230V AC/12V/24V DC 330(L)x112(W)x83(D) mm Power: 10/25W

PB-12-D-16-1XOA 16x1W LED 220V AC 1x1ft Cut Out: 275x275 mm Power: 20W

PB-11-D-L-WXOD 9x0.3/15x0.3W LED 230V AC 91(f)x40(D) mm Cut Out: 75 mm Power: 5/7W

PD-12-P-L-1XOA 6x1/9x1W LED (3R+3G+3B) 230V AC/12V DC 8°/15°/25°/45°/60° Lens 165(ø)x130(H) mm Cut Out:120(ø) mm Power: 8/12W

Retrofit solutions available Die-Cast aluminium housing Toughened type ‘A’ glass Flameproof/Non Flamepro of enclosure Optimum thermal management High brightness power LED IP-65 Flamepro of PF-11-D-L-1XOA 24x1/32x1W LED 230V AC Without Lens 240(ø)x160(D) mm Power: 30/40W

PD-17-P-L-WXOA 50W LED 230V AC 305(ø)x270(H) mm Power: 50W

PQ-11-P-L-WXOA 1X1W LED 1800-2600 mAH Battery Backup 4-6 Hrs.280(ø)x212 (H)x125(W) mm Power: 2W

Power efficiency > 80 % Power factor > 0.9 (above 6W) Toughened glass/Polycarbonate diffuser Anti-Corrosive surface treatment Superior finish with epoxy powder coating IP-65   PD-15-D-6-1X00A 6x1W LED 230V AC 100(f)x485(H) mm Power: 8W

Power efficiency > 80 % Power factor > 0.9 High quality toughened glass diffuser High brightness, mono or RGB color, RGB synchronous color changing system Short circuit, open circuit protection on driver Application specific beam angles PD-17-P-L-WXOA 36x0.4W LED 230V AC/24V AC 180(L)x108(H)x140(W) mm Power: 20W

Up to 80% energy saving Power efficiency>80 % (above 3W) Aesthetically designed aluminium extruded /die-cast enclosures Short circuit & open circuit protection on driver Dimming optional, Choice of colors   PB-13-D-L-WXOA 9x0.3W LED 230V AC 80(f)x21(D) mm Cut Out: 68 mm Power: 3W

PA-16-D-L-WXOA 50x0.2W LED 230V AC 80(f)x155(H) mm Power: 10W