Shamlax Metachem Private Limited Kamptee, Nagpur, Maharashtra

Zircon Solvent based yellow colored coating, suitable for Sodium-Silicate Alpha Set Resin Sand System. Changes color from Yellow to Orange on ignition. To eliminate all moisture related defects To identify poor sand compaction in a core or mould. [as these areas will absorb more moisture from coating and will take longer time to dry] To optimize on cost of drying – Avoid over heating by oven torch

It is a well know fact that the Foundry Coatings are widely used to improve the surface casting finish and to achieve the best cosmetic look of the castings. But at the same time we all know that the best of the Foundry coating can never achieve this on a bad core or moulds. A conventional foundry using Sodium silicate CO2 gassed binder system uses mostly solvent based refractory coatings. In view of improving productivity, castings quality, to reduce rejection %, to have cleaner environment in the foundry, all modern foundries are shifting to modern resin systems such as phenolic ester cured, cold box resins, shell sand (Hot-Box), Furan Resin, Alpha set etc. Most of these sand resin systems whether for moulds or cores utilizes water based coatings to avoid casting defects such as metal penetration, sand erosion, veining etc.

Sandaid-50 – is a lustrous carbon additive specially designed with selected volatile content for iron foundry green sand. Exoaid–61 - is a sand additive to eliminate sand expansion defects such as scabs, buckles. Exoaid-61 high burn-out temperature contents and results in lower concentration of dead clay. This improves permeability, reduces moisture requirements and gives better all-round sand properties over a longer life-cycle. Addition % of Exoaid – 61 is 0.5 - 1.0 % in the facing sand. If it is added in total sand system than 0.05 – 0.1% is sufficient. Exoaid–81 – is an anti veining sand additive. It is free from contaminants such as oil, moisture, acid salts, slag and gangue minerals.

We offer melting fluxes. in case of scrap melting, slag is generated due to various impurities in scrap. This slag if not removed will cause slag-inclusions in castings causing rejections. These slag inclusions can be easily removed by using slag-stick-30.

We offer moltan metal transfer. In case of continuous castings, hot-liquid metal is poured through tundish tank, lined with highly refractory tundish spray to maintain the steel temperature during the process.

Exotherm-500 : Exothermic Riser Sleeves MEF1.6 and above. Sizes from 2" to 24". Custom Shapes also available. Inotherm-600 : Highly Insulating Sleeves MEF 1.4 to 1.6. Sizes 6" and above. N. D. Sleeves : Knock Down Sleeves of various sizes.

Modified co2 binders is a complex one shot sand additive binder for co2 gassed process. It offers a combination of high strength and rapid gassing with good core storage properties and excellent post casting breakdown.

Wooden pattern & core boxes are frequently used for short run work. Epoxy or other resin pattern are common & metal equipments may be used for longer running work. The chemical binders used may be acid or alkaline or may contain organic solvents which can attack the pattern or paints.

We are offering various types of mould & core coatings that are available at very reasonable prices.

We are leading manufacturer, supplier and exporter of huge range of Equipments.

We deals in manufacturing, supplying and exporting of wide range of Portable Can Mixer.

We are well known for manufacturing, supplying and exporting of wide variety of flow coating station.

We are offering best Batch Mixer.

One of the best Metal Treatment in India.

We are india's leading manufacturer & supplier of copper alloys drossing.

One of the pioneer suppliers of industrial products based in india, providing various types of products such as covering fluxes.

An eminent supplying company based in india, providing a various types of products such as non-ferrous coatings.