Industrial Dryers Dealers in Nashik

Flash drying systems is in which particulate solids are dried during transport in a hot gas stream usually air or combustion gases. The simple flash drying system includes six basic components: the gas heater, the wet material feeder, the drying duct, the separator, exhaust fan, and a dried product collector. The wet particles are fed into the hot gas stream sometimes with special mixing devices. The stream flows up the drying tube. The gas velocity must be greater than the free fall velocity of the largest particle to be dried. The gas velocity in relation to the particle velocity is high. Thermal contact between the conveying air and the solids as mentioned above is usually very short and therefore flash dryers are most suitable for removal of external moisture (surface moisture) and are less suitable for removal of internal moisture. At the end of the drying process a dust separation arrangement is installed. It must comply with the regulations for pollution control. For this purpose cyclone dust separators, fabric filters, electrostatic precipitators, wet scrubbers, and fabric filters are used. Flash dryers are used in various Sectors of the chemical, pharmaceutical, ceramic, gypsum, wood, and mining industries. Flash dryers are simple in construction and have low capital cost and they are almost trouble free.

Product Description   Applications : Tray dryers are ideally suitable for drying chilies, spices, papads, potato chips, onions, fish, garlic, grapes, cashew nuts, confectionery, macaroni, wood etc. It is  also for used for drying pharmaceuticals, chemicals, powders, granules, plastic granules etc. Heating is either by electric or steam or both combined. Various models are listed in this leaflet to suit customer requirements. Custom-built models can be quoted on request.   Construction : The external frame work is made of thick gauge m. S plates both the exterior made of thick gauge crca sheets or aisi 304 sheets. In between the space, resin bonded special quality fiber glass heat insulation slabs are provided. Safety guards for fan blade & heaters are provided. The interiors is painted with heat resistant aluminum paint. The exterior is spray painted with silver gray gloss paint, inner chamber – crca or aisi 304, outer chamber – crca or aisi 304.   Fan & Motor : According to models doors are provided with smooth moving hinges, latch catch & sealing gaskets. Well balanced large propeller type fan (s) fitted inside the chamber with suitable shaft & dual bearing with electric motor (s) drive.   Heaters : ‘U’ type tubular heaters are provided inside the chamber for maximum heat transfer. Steam heated models are fitted with finned type steam radiators.   Controls Panel : Control panel box consists of contactor assembly, on & off switch, digital controller  neon lamps, operating push buttons are incorporated in the control box.   Damper : Adjustable exhaust damper with an arrangement for pre-filtration, in the air inlet.   Optional : Gmp models/complete s. S unit. Trolleys & trays supplied as per requirement. Microprocessor based temp. Control with printer interface (centronic pc interface with rs 232 cpc/rs-485 for networking of controllers. Profile controller for ramp/soak cyclic applications.   Safety Features : Built-in temp. Deviation audio visual alarm. Safety thermostat for over shoot temp. Cut off circuit to cut off the whole systems in case of malfunction. (only applicable to microprocessor based models).   Validation : Iq oq pq & dq protocols with complete documentation & certification traceable to national & international standards.   Steam Heated Models : These are provided with finned tubular steam coils instead of/in addition to heaters, along with solenoid valve.

• Type: Customized
• Certification: CE Certified
• Voltage: 380V
• Automatic Grade: Automatic
• Driven Type: Electric
• Capacity: .5 to 10 Square Meter
• Max. Temperature: 150 Degree Celsius

• Certification: NA
• Application: Pharmaceuticals
• Weight: 100-200kg, 200-300kg, 300-400kg, 400-500kg, 150 TO 200 KG
• Color: SILVER
• Voltage: 440V
• Condition: New
• Automatic Grade: Manual, Semi Automatic
• Power: 10-15kw, 15-20kw, 15 TO 30 KW
• Driven Type: Electric, STEAM
• Warranty: 1year
• Country of Origin: India
• Type: PHARMACEUTICAL TRAY DRIER
• Brand Name: HPT - TD
• After-Sales Service Provided: NA
• Product: NA

• Material: Stainless Steel
• Type: Rotary and Nozzle Type
• Capacity: Upto 60 TPD
• Usage/Application: Spray drying is used to dry pharmaceutical fine chemicals, foods, dairy products, blood plasma.
• Surface Finish: Polished
• Automation Grade: Automatic
• Design: Customized
• Control System: MIMIC, PLC- HMI, PLC-SCADA etc.
• Brand: SVAAR

Centrifugal Dryer, plating barrel, filtration unit, Plating Tank

Spin Flash Dryer, Plastic Injection Moulds, Spray Dryer, spray coolers

Agitated Thin Film Dryer, wiped film evaporator, Rising Film Evaporator

agitated thin film dryers, distilleries

Tray Dryer, V-Blender, Contra Rotary Mixer, Octagonal Blender

Agitated Thin Film Dryer