Air Spray Solution Ghansoli, Navi Mumbai, Maharashtra

Features of ZC 876 Shiny Cold Galvanizing Coating ZC 876 Shiny Cold Galvanizing Coating is provides all metal surfaces, such as hot-dip galvanised parts being repaired, with permanent, cathodic corrosive protection. It forms a quick-drying, adhesive, protective layer of micro fine zinc flakes. Provides maximum protection against the formation or spread of rust and corrosion. Excellent Outdoor & Indoor protection Outstanding corrosion High temperature resistance True galvanic protection   Application of ZC 876 Shiny Cold Galvanizing Coating It use in All vehicle bodies Agricultural, mining and construction equipment, Piping, storage tanks, Bridges, Ships and marine equipment, Refinery, Water treatment, Pulp & paper,Steel Automobile etc.   Direction of ZC 876 Shiny Cold Galvanizing Coating Surface should be dry and free of rust bloom. Shake well until agitator ball is free. Repeat while using. Best results are obtained when sprayed above 60º F. Spray from 12-15 inches away in light, even coats. The optimum film thickness for Bright Zinc is 1.5 to 3.0 mils of dry film. To obtain this thickness via aerosol application, 3 passes of spray are required. Spray the substrate once vertically, once horizontally, and once more vertically for ideal coverage. Additional coats for heavy film can be applied when first coat is dry. For a thickness of 3 mils, repeat the above spray pattern twice. When finished spraying, clean valve by turning can upside down and pressing button until only pressure escapes. If clogging occurs, remove button and clean slot and orifice with fine wire.   Precaution of ZC 876 Shiny Cold Galvanizing Coating Contents are Extremely Flammable and Under Pressure. Do not punctured, may explode if heated. Do not apply while equipment is energized, Keep away from all live electrical sources including battery terminals, solenoids, electrical panels and other electronic components. Prevention : Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurized container : Do not pierce or burn even after use. Do not spray on an open flame or other ignition source,live circuits. Harmful in contact with eyes. Prolonged exposure may cause chronic effects. May cause drowsiness and dizziness Response : IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTRE ;or physician if you feel unwell. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.   Storage of ZC 876 Shiny Cold Galvanizing Coating Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50°C/122 °F. Store in a well-ventilated place. Keep container tightly closed. Keep Out of Reach of Children.

Form : Liquid

Packaging Type : Can

Shelf Life : 1 Yr

Features of ZC 678 Anti corrosion Bright zinc coating ZC 678 Anti corrosion Bright zinc coating is Inhibits rust and corrosion on ferrous metals. Stops rust and corrosion on any iron or steel surface, Provides the appearance of a hot-dip galvanised, Highly resistant to scratching, denting, abrasion, corrosive environments, salt air, heat, moisture and road salts. Quick-drying Non-sagging touch-up of damaged galvanising Its galvanic action ensures better self-healing and sealing   Application of ZC 678 Anti corrosion Bright zinc coating Bright-Zinc is the original metallic silver colour zinc-rich coating that has been used on towers, power generators, farms, fencing ,Air conditioning equipment / ducts, satellite, antennas. It is used as an anti rust primer on vehicle bodies.It forms a protective coating on welded and drilled section. Used in Marine works and ship manufacturing parts and repairing. also used in heavy equipment, pipes, transformers, electrical poles, threads, welds, automobile, Metal chain fences, storage tanks etc. They are invaluable for use in : Construction Agriculture, Local authorities, Railway, Welding, transport, Automotive, Engineering,   Direction of ZC 678 Anti corrosion Bright zinc coating Surface should be dry and free of rust bloom. Shake well until agitator ball is free. Repeat while using. Best results are obtained when sprayed above 60º F. Spray from 12-15 inches away in light, even coats. The optimum film thickness for Bright Zinc is 1.5 to 3.0 mils of dry film. To obtain this thickness via aerosol application, 3 passes of spray are required. Spray the substrate once vertically, once horizontally, and once more vertically for ideal coverage. Additional coats for heavy film can be applied when first coat is dry. For a thickness of 3 mils, repeat the above spray pattern twice. When finished spraying, clean valve by turning can upside down and pressing button until only pressure escapes. If clogging occurs, remove button and clean slot and orifice with fine wire.   Precaution of ZC 678 Anti corrosion Bright zinc coating Contents are Extremely Flammable and Under Pressure. Do not punctured , may explode if heated. Do not apply while equipment is energised, Keep away from all live electrical sources including battery terminals, solenoids, electrical panels and other electronic components. Prevention : Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurised container: Do not pierce or burn, even after use. Do not spray on an open flame or other ignition source,live circuits. Harmful in contact with eyes. Prolonged exposure may cause chronic effects. May cause drowsiness and dizziness Response : IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTRE or physician if you feel unwell. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.   Storage of ZC 678 Anti corrosion Bright zinc coating Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50°C/122 °F. Store in a well-ventilated place. Keep container tightly closed. Keep Out of Reach of Children.

Color : Silver

Features of ZC 876 Shiny Cold Galvanizing Coating : ZC 876 Shiny Cold Galvanizing Coating is provides all metal surfaces, such as hot-dip galvanised parts being repaired, with permanent, cathodic corrosive protection. It forms a quick-drying, adhesive, protective layer of micro fine zinc flakes. Provides maximum protection against the formation or spread of rust and corrosion. Excellent Outdoor & Indoor protection Outstanding corrosion High temperature resistance True galvanic protection   Application of ZC 876 Shiny Cold Galvanizing Coating It use in All vehicle bodies Agricultural, mining and construction equipment, Piping, storage tanks, Bridges, Ships and marine equipment, Refinery, Water treatment, Pulp & paper,Steel Automobile etc.   Direction of ZC 876 Shiny Cold Galvanizing Coating Surface should be dry and free of rust bloom. Shake well until agitator ball is free. Repeat while using. Best results are obtained when sprayed above 60º F. Spray from 12-15 inches away in light, even coats. The optimum film thickness for Bright Zinc is 1.5 to 3.0 mils of dry film. To obtain this thickness via aerosol application, 3 passes of spray are required. Spray the substrate once vertically, once horizontally, and once more vertically for ideal coverage. Additional coats for heavy film can be applied when first coat is dry. For a thickness of 3 mils, repeat the above spray pattern twice. When finished spraying, clean valve by turning can upside down and pressing button until only pressure escapes. If clogging occurs, remove button and clean slot and orifice with fine wire.   Precaution of ZC 876 Shiny Cold Galvanizing Coating Contents are Extremely Flammable and Under Pressure. Do not punctured, may explode if heated. Do not apply while equipment is energized, Keep away from all live electrical sources including battery terminals, solenoids, electrical panels and other electronic components. Prevention : Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurized container : Do not pierce or burn even after use. Do not spray on an open flame or other ignition source,live circuits. Harmful in contact with eyes. Prolonged exposure may cause chronic effects. May cause drowsiness and dizziness Response : IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTRE ;or physician if you feel unwell. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.   Storage of ZC 876 Shiny Cold Galvanizing Coating Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50°C/122 °F. Store in a well-ventilated place. Keep container tightly closed. Keep Out of Reach of Children.

Type : Cold Galvanizing Spray

Application : Industrial Use

Shelf Life : 1 Yr

Purity : 99 %

Feature : Bright Metallic Finish,Good Result,High Shine Finish,Quality Approved

Form : Liquid

Packaging Type : Can

Country of Origin : India

Packaging Size : 450 ML

Features of RIV 2030 highly insulating varnish in convenient aerosol RIV 2030 It is a highly insulating varnish in convenient aerosol form It is a high gloss red color high temperature flexible chemical resistance coating to Class F winding or electrical apparatus It is specially designed for protection and sealing of insulated surface against deterioration, exposure to oil, moisture, acid and alkaline fumes. Excellent Adhesion Quick drying Protects against moisture and corrosion Class F air drying single component. Environmental friendly. INSULATING SPRAY aerosol packing is CFC-free.   Application of RIV 2030 highly insulating varnish in convenient aerosol It can be used for protection of Small field and magnet coils, motor windings, field coils, transformers, armatures, commutator ends, stator windings, ring and frames, bus bars, sealing electrical, switchboard parts and electronic components. motor case interiors, collector rings and shells, field winding of motor starters and generators etc.   Direction of RIV 2030 highly insulating varnish in convenient aerosol Shake well before use until the sound of the ball is audible. clean & degrease surface Hold the can at least 10 to 12 cm from the surface you are spraying and keep the can upright during use.Protect & Mask areas not Coated. Two light coats is best results better than one heavy coat.Coating becomes dry in 20 minutes. make sure the surface is completely dry before using.completed cure takes place in about 24 hours depends upon the humidity. & maintain full pressure on valve while spraying. Repeat spraying whenever necessary. When finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes.   Precaution of RIV 2030 highly insulating varnish in convenient aerosol Contains gas under pressure do not punctured ,may explode if heated. Extremely flammable Prevention : Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurized container: Do not pierce or burn, even after use. Do not spray on an open flame or other ignition source. Use only outdoors or in a well-ventilated area. Avoid breathing vapor. Wash hands thoroughly after handling. Causes serious eye irritation. May cause drowsiness and dizziness Response IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.   Storage of RIV 2030 highly insulating varnish in convenient aerosol Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50°C/122 °F. Store in a well-ventilated place.keep container tightly closed. Keep Out of Reach of Children

Type : Industrial Automation

Brand Name : ASS

Application : Industrial Use

features of riv 2030 highly insulating varnish in convenient aerosol riv 2030 it is a highly insulating varnish in convenient aerosol form it is a high gloss red color high temperature flexible chemical resistance coating to class f winding or electrical apparatus it is specially designed for protection and sealing of insulated surface against deterioration, exposure to oil, moisture, acid and alkaline fumes. excellent adhesion quick drying protects against moisture and corrosion class f air drying single component. environmental friendly. insulating spray aerosol packing is cfc-free.   application of riv 2030 highly insulating varnish in convenient aerosol it can be used for protection of small field and magnet coils, motor windings, field coils, transformers, armatures, commutator ends, stator windings, ring and frames, bus bars, sealing electrical, switchboard parts and electronic components. motor case interiors, collector rings and shells, field winding of motor starters and generators etc.   direction of riv 2030 highly insulating varnish in convenient aerosol shake well before use until the sound of the ball is audible. clean & degrease surface hold the can at least 10 to 12 cm from the surface you are spraying and keep the can upright during use.protect & mask areas not coated. two light coats is best results better than one heavy coat.coating becomes dry in 20 minutes. make sure the surface is completely dry before using.completed cure takes place in about 24 hours depends upon the humidity. & maintain full pressure on valve while spraying. repeat spraying whenever necessary. when finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes.   precaution of riv 2030 highly insulating varnish in convenient aerosol contains gas under pressure do not punctured ,may explode if heated. extremely flammable prevention : wear eye or face protection. keep away from heat, hot surfaces, sparks, open flames and other ignition sources. no smoking. pressurized container: do not pierce or burn, even after use. do not spray on an open flame or other ignition source. use only outdoors or in a well-ventilated area. avoid breathing vapor. wash hands thoroughly after handling. causes serious eye irritation. may cause drowsiness and dizziness response if inhaled: remove victim to fresh air and keep at rest in a position comfortable for breathing. call a poison center or physician if you feel unwell. if in eyes: rinse cautiously with water for several minutes. remove contact lenses, if present and easy to do. continue rinsing. if eye irritation persists: get medical attention. dispose of contents and/or container according to federal, state/provincial and local governmental regulations.   storage of riv 2030 highly insulating varnish in convenient aerosol store locked up. protect from sunlight. do not expose to temperatures exceeding 50°c/122 °f. store in a well-ventilated place.keep container tightly closed. keep out of reach of children

Brand Name : Ass

Country of Origin : India

Features of HR 567 Heat Resistant Spray HR 567 Heat Resistant Spray is High heat resistant coating, For all exposed metal surfaces, especially where extreme heat resistance is required, air dries quickly on application to form long lasting finish resistant to surface temperatures reaching as 700°C. Rapid drying to a very tough finish Very good resistance to moisture and chemicals good anti-corrosion characteristics Excellent adhesion to composites and aluminium   Application of HR 567 Heat Resistant Spray Heat resistant paints are designed to withstand high temperatures of up to 700°C, Which makes them ideal for use on fireplaces,  chimneys, pipes,  engines,  exhaust pipes, log-burners and many more metal / metallic items requiring heat proof treatment.   Direction of HR 567 Heat Resistant Spray Remove dirt, grease, oil, loose rust and all other surface contaminants by appropriate means. Sand intact coatings to roughen the surface slightly. The surface must be clean and dry during application. Remove cover cap. Shake vigorously for at least one minute after the rattle of mixing ball is heard. Shake frequently during use. Hold can approx. 30 cm from surface. Use back and forth motion keeping can parallel with surface. Ensure that can is in motion when spray button is pressed to avoid runs and sags. Apply several thin layers at a few minutes interval to achieve adequate coating thickness. After use turn can upside down and press spray button for 2 – 3 seconds to clean valve.   Precaution of HR 567 Heat Resistant Spray Contents are Extremely Flammable and Under Pressure, Do not punctured ,may explode if heated. Do not apply while equipment is energised,Keep away from all live electrical sources including battery terminals, solenoids, electrical panels and other electronic components. Prevention : Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurised container: Do not pierce or burn, even after use. Do not spray on an open flame or other ignition source,live circuits. Harmful in contact with eyes. Prolonged exposure may cause chronic effects. May cause drowsiness and dizziness Response : IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. IF IN Eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.   Storage of HR 567 Heat Resistant Spray Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50°C/122 °F. Store in a well-ventilated place. Keep container tightly closed. Keep Out of Reach of Children.

Packaging Type : Tin Bottle

Packaging Size : 430 Ml

features of hd 1014 - heavy duty motor cleaner it is a degreasing agent with high dielectric resistance for cleaning electric motors and other equipments. it instantly penetrates and removes dirt, moisture, oil, wax and grease from electrical equipment and machinery to clean and degrease electrical equipment when electrical current exists, this prevents intermittent failure of equipment due to flash-overs or short circuits.   application of hd 1014 - electronic and electrical parts contact cleaner motor cleaner has been designed for the specific cleaning and degreasing of electric motors, generators,switch gears,terminal, air conditioners, fans, transformers and tools. it quickly removes grease, tar, carbon deposits and all dirt characteristic to this kind of equipment   direction of hd 1014 - heavy duty motor cleaner shake well before use until the sound of the ball is audible. clean & degrease surface hold the can at least 10 to 12 cm from the surface you are spraying and keep the can upright during use.protect & mask areas not coated. two light coats is best results better than one heavy coat.coating becomes dry in 20 minutes. make sure the surface is completely dry before using.completed cure takes place in about 24 hours depends upon the humidity. & maintain full pressure on valve while spraying. repeat spraying whenever necessary. when finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes.   precaution of hd 1014 - heavy duty motor cleaner contains gas under pressure do not punctured ,may explode if heated. extremely flammable prevention : wear eye or face protection. keep away from heat, hot surfaces, sparks, open flames and other ignition sources. no smoking. pressurized container: do not pierce or burn, even after use. do not spray on an open flame or other ignition source. use only outdoors or in a well-ventilated area. avoid breathing vapor. wash hands thoroughly after handling. causes serious eye irritation. may cause drowsiness and dizziness response : if inhaled: remove victim to fresh air and keep at rest in a position comfortable for breathing. call a poison center or physician if you feel unwell. if in eyes: rinse cautiously with water for several minutes. remove contact lenses, if present and easy to do. continue rinsing. if eye irritation persists: get medical attention. dispose of contents and/or container according to federal, state/provincial and local governmental regulations.   storage of hd 1014 - heavy duty motor cleaner store locked up. protect from sunlight. do not expose to temperatures exceeding 50°c/122 °f. store in a well-ventilated place.keep container tightly closed. keep out of reach of children

Brand Name : ASS

Country of Origin : India

Usage : Industrial

features of hd 1015 - heavy duty mechanical parts cleaner heavy duty parts cleaner is designed to penetrate and effectively dissolve and remove oil, grease, brake fluid, and other soils from all metal parts, heavy machinery, farming equipment, mining equipment, and any other mechanical parts in extremely difficult situation. low odour properties improve operator working conditions.will quickly and effectively flush built up grease from chains and slides on forklifts, wire ropes and all types of industrial equipment.   application of hd 1015 - heavy duty mechanical parts cleaner the product is designed to be effective in heavy duty cleaning of machine parts, disc & drum brakes and forklift chains, wire ropes, open gears, bearings, valves, sprockets etc.   direction of hd 1015 - heavy duty mechanical parts cleaner shake well before use until the sound of the ball is audible. clean & degrease surface hold the can at least 10 to 12 cm from the surface you are spraying and keep the can upright during use.protect & mask areas not coated. two light coats is best results better than one heavy coat.coating becomes dry in 20 minutes. make sure the surface is completely dry before using.completed cure takes place in about 24 hours depends upon the humidity. & maintain full pressure on valve while spraying. repeat spraying whenever necessary. when finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes.   precaution of hd 1015 - heavy duty mechanical parts cleaner contains gas under pressure do not punctured ,may explode if heated. extremely flammable prevention : wear eye or face protection. keep away from heat, hot surfaces, sparks, open flames and other ignition sources. no smoking. pressurized container: do not pierce or burn, even after use. do not spray on an open flame or other ignition source. use only outdoors or in a well-ventilated area. avoid breathing vapor. wash hands thoroughly after handling. causes serious eye irritation. may cause drowsiness and dizziness response : if inhaled: remove victim to fresh air and keep at rest in a position comfortable for breathing. call a poison center or physician if you feel unwell. if in eyes: rinse cautiously with water for several minutes. remove contact lenses, if present and easy to do. continue rinsing. if eye irritation persists: get medical attention. dispose of contents and/or container according to federal, state/provincial and local governmental regulations.   storage of hd 1015 - heavy duty mechanical parts cleaner store locked up. protect from sunlight. do not expose to temperatures exceeding 50°c/122 °f. store in a well-ventilated place.keep container tightly closed. keep out of reach of children

Type : Heavy Duty Mechanical Parts Cleaner

Application : Cleaning

Country of Origin : India

Brand Name : ASS

Features of HR 567 Heat Resistant Spray HR 567 Heat Resistant Spray is High heat resistant coating, For all exposed metal surfaces, especially where extreme heat resistance is required, air dries quickly on application to form long lasting finish resistant to surface temperatures reaching as 700°C. Rapid drying to a very tough finish Very good resistance to moisture and chemicals good anti-corrosion characteristics Excellent adhesion to composites and aluminium   Application of HR 567 Heat Resistant Spray Heat resistant paints are designed to withstand high temperatures of up to 700°C, Which makes them ideal for use on fireplaces,  chimneys, pipes,  engines,  exhaust pipes, log-burners and many more metal / metallic items requiring heat proof treatment.   Direction of HR 567 Heat Resistant Spray Remove dirt, grease, oil, loose rust and all other surface contaminants by appropriate means. Sand intact coatings to roughen the surface slightly. The surface must be clean and dry during application. Remove cover cap. Shake vigorously for at least one minute after the rattle of mixing ball is heard. Shake frequently during use. Hold can approx. 30 cm from surface. Use back and forth motion keeping can parallel with surface. Ensure that can is in motion when spray button is pressed to avoid runs and sags. Apply several thin layers at a few minutes interval to achieve adequate coating thickness. After use turn can upside down and press spray button for 2 – 3 seconds to clean valve.   Precaution of HR 567 Heat Resistant Spray Contents are Extremely Flammable and Under Pressure, Do not punctured ,may explode if heated. Do not apply while equipment is energised,Keep away from all live electrical sources including battery terminals, solenoids, electrical panels and other electronic components. Prevention : Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurised container: Do not pierce or burn, even after use. Do not spray on an open flame or other ignition source,live circuits. Harmful in contact with eyes. Prolonged exposure may cause chronic effects. May cause drowsiness and dizziness Response : IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. IF IN Eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.   Storage of HR 567 Heat Resistant Spray Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50°C/122 °F. Store in a well-ventilated place. Keep container tightly closed. Keep Out of Reach of Children.

Feature : Heat Resitant

Condition : New

Country of Origin : India

Brand Name : ASS

Features of HD 1015 - Heavy Duty Mechanical Parts Cleaner Heavy Duty Parts Cleaner is designed to penetrate and effectively dissolve and remove oil, grease, brake fluid, and other soils from all metal parts, heavy machinery, farming equipment, mining equipment, and any other mechanical parts in extremely difficult situation. Low odour properties improve operator working conditions.Will quickly and effectively flush built up grease from chains and slides on forklifts, wire ropes and all types of industrial equipment.   Application of HD 1015 - Heavy Duty Mechanical Parts Cleaner The product is designed to be effective in heavy duty cleaning of machine parts, disc & drum brakes and forklift chains, wire ropes, open gears, bearings, valves, sprockets etc.   Direction of HD 1015 - Heavy Duty Mechanical Parts Cleaner Shake well before use until the sound of the ball is audible. clean & degrease surface Hold the can at least 10 to 12 cm from the surface you are spraying and keep the can upright during use.Protect & Mask areas not Coated. Two light coats is best results better than one heavy coat.Coating becomes dry in 20 minutes. make sure the surface is completely dry before using.completed cure takes place in about 24 hours depends upon the humidity. & maintain full pressure on valve while spraying. Repeat spraying whenever necessary. When finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes.   Precaution of HD 1015 - Heavy Duty Mechanical Parts Cleaner Contains gas under pressure do not punctured ,may explode if heated. Extremely flammable Prevention : Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurized container: Do not pierce or burn, even after use. Do not spray on an open flame or other ignition source. Use only outdoors or in a well-ventilated area. Avoid breathing vapor. Wash hands thoroughly after handling. Causes serious eye irritation. May cause drowsiness and dizziness Response : IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.   Storage of HD 1015 - Heavy Duty Mechanical Parts Cleaner Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50°C/122 °F. Store in a well-ventilated place.keep container tightly closed. Keep Out of Reach of Children

Brand Name : ASS

Features of HD 1014 - Heavy Duty Motor Cleaner It is a degreasing agent with high dielectric resistance for cleaning electric motors and other equipments. it instantly penetrates and removes dirt, moisture, oil, wax and grease from electrical equipment and machinery to clean and degrease electrical equipment when electrical current exists, this prevents intermittent failure of equipment due to flash-overs or short circuits.   Application of HD 1014 - Electronic and Electrical parts contact cleaner motor cleaner has been designed for the specific cleaning and degreasing of electric motors, generators,Switch gears,Terminal, air conditioners, fans, transformers and tools. It quickly removes grease, tar, carbon deposits and all dirt characteristic to this kind of equipment   Direction of HD 1014 - Heavy Duty Motor Cleaner Shake well before use until the sound of the ball is audible. clean & degrease surface Hold the can at least 10 to 12 cm from the surface you are spraying and keep the can upright during use.Protect & Mask areas not Coated. Two light coats is best results better than one heavy coat.Coating becomes dry in 20 minutes. make sure the surface is completely dry before using.completed cure takes place in about 24 hours depends upon the humidity. & maintain full pressure on valve while spraying. Repeat spraying whenever necessary. When finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes.   Precaution of HD 1014 - Heavy Duty Motor Cleaner Contains gas under pressure do not punctured ,may explode if heated. Extremely flammable Prevention : Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurized container: Do not pierce or burn, even after use. Do not spray on an open flame or other ignition source. Use only outdoors or in a well-ventilated area. Avoid breathing vapor. Wash hands thoroughly after handling. Causes serious eye irritation. May cause drowsiness and dizziness Response : IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.   Storage of HD 1014 - Heavy Duty Motor Cleaner Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50°C/122 °F. Store in a well-ventilated place.keep container tightly closed. Keep Out of Reach of Children

Type : Industrial Automation

Brand Name : ASS

Features of NDT 102 Non Destructive testing Detects Surface defects upto 1 micron width x 30 micron depth on Standard Ni - Cr Test Panel. Low halides and Sulphate contents. Non - corrosive and non - toxic. The quick opertional sequence makes results available immediately. Convenient and easy to handle pressurised cans and bulk containers to suit various industrial needs. A General purpose, verstile and inexpensive technique.   Environment friendly CLEANER SPRAY- is an aerosol applied cleaner used as part of the NDT crack detection system for pre-use cleaning, also for the easy removal of RMC RED DYE and RMC DEVELOPER Sprays. Cuts through dirt, grease and grime Zero residue Prepares surface for non destructive testing   DEVELOPER SPRAY - is an aerosol applied white powder that is designed to draw the penetrant out of a flaw to enhance the definition. It is used to facilitate detection when used in conjunction with the NDT crack detection system. Highly absorbent white film for rapid results Highlights very fine cracks Sharp indication and geometry of defect to the naked eye Suitable for pressure testing & leak detection   Dye Penetrant Spray - Dye Penetrant is an aerosol applied dye which can be sprayed from any angle. Used as part of the NDT crack detection system. Bright red even film Highly sensitive dye Water washable   Application of NDT 102 Non Destructive testing Non-destructive inspection system is designed to provide a fast reliable method for visual detection of cracks or flaws which would not normally be visible to the naked eye. Ideal for the inspection of welded joints, castings, forgings etc. non-destructive testing kit includes the cleaner, penetrant and developer spray in a convenient carrypack. Cleaner : Stainless Steel,Titanium,Nickel,Carbides,Ceramic and certain plastics,Pressure,Vessels,Pipelines,Heat Exchangers,Casting and Forgings. Developer :Aluminum,Magnesium,Brass,Copper,Cast Iron,Steel,Pipelines,Heat,Exchangers,Casting and Forgings,Petrochemical plants,Boilers. Dye Penetrant : Pressure Vessels,Pipelines,Heat Exchangers,Casting and Forgings,Petrochemical plants,Boilers and others   Direction of use of NDT 102 Non Destructive testing Shake well before use. Clean the surface to removed dust with clean cloth. Hold the can at least 8 to 12 cm from the surface you are spraying and keep the can upright during use. repeat the same every after every 8-10 operations. wipe off the spatter with a light cloth. When finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes   Precaution of NDT 102 Non Destructive testing Contents are Extremely Flammable and Under Pressure, Do Not Puncture Prevention : Keep away from heat, sparks, open flames, hot surfaces. No smoking. Avoid breathing dust, fume, gas, mist, vapours, spray. Use only outdoors or in a well-ventilated area. do not contaminate water supply. incinerate or store above 50°C. Exposure to high temperatures may cause can to burst. Do not place in direct sunlight or near any heat source. Aerosol cans will conduct electricity. Keep away from all live electrical sources including battery terminals, solenoids, electrical panels and other electronic components. Failure to observe this warning may result in serious injury from flash fire and/or electrical shock.   First Aid : Swallowed – Not considered a normal route of entry. Do not induce vomiting. Seek medical advice. Avoid giving milk or oils. Avoid giving alcohol. Skin – Flush skin and hair with running water (and soap if available). Remove any adhering solids with industrial skin cleansing cream. 

features of ndt 103 non destructive testing detects surface defects upto 1 micron width x 30 micron depth on standard ni - cr test panel. low halides and sulphate contents. non - corrosive and non - toxic. the quick opertional sequence makes results available immediately. convenient and easy to handle pressurised cans and bulk containers to suit various industrial needs. a general purpose, verstile and inexpensive technique.   environment friendly cleaner spray- is an aerosol applied cleaner used as part of the ndt 103rack detection system for pre-use cleaning, also for the easy removal of rmc red dye and rmc developer sprays. cuts through dirt, grease and grime zero residue prepares surface for non destructive testing   developer spray -is an aerosol applied white powder that is designed to draw the penetrant out of a flaw to enhance the definition. it is used to facilitate detection when used in conjunction with the ndt 103rack detection system. highly absorbent white film for rapid results highlights very fine cracks sharp indication and geometry of defect to the naked eye suitable for pressure testing & leak detection   dye penetrant spray-dye penetrant is an aerosol applied dye which can be sprayed from any angle. used as part of the ndt 103rack detection system. bright red even film highly sensitive dye water washable   application of ndt 103 non destructive testing non-destructive inspection system is designed to provide a fast reliable method for visual detection of cracks or flaws which would not normally be visible to the naked eye. ideal for the inspection of welded joints, castings, forgings etc. non-destructive testing kit includes the cleaner, penetrant and developer spray in a convenient carrypack. cleaner : stainless steel,titanium,nickel,carbides,ceramic and certain plastics,pressure,vessels,pipelines,heat exchangers,casting and forgings. developer :aluminum,magnesium,brass,copper,cast iron,steel,pipelines,heat,exchangers,casting and forgings,petrochemical plants,boilers. dye penetrant : pressure vessels,pipelines,heat exchangers,casting and forgings,petrochemical plants,boilers and others   direction of use of ndt 103 non destructive testing shake well before use. clean the surface to removed dust with clean cloth. hold the can at least 8 to 12 cm from the surface you are spraying and keep the can upright during use. repeat the same every after every 8-10 operations. wipe off the spatter with a light cloth. when finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes   precaution of ndt2 non destructive testing contents are extremely flammable and under pressure, do not puncture prevention : keep away from heat, sparks, open flames, hot surfaces. no smoking. avoid breathing dust, fume, gas, mist, vapours, spray. use only outdoors or in a well-ventilated area. do not contaminate water supply. incinerate or store above 50°c. exposure to high temperatures may cause can to burst. do not place in direct sunlight or near any heat source. aerosol cans will conduct electricity. keep away from all live electrical sources including battery terminals, solenoids, electrical panels and other electronic components. failure to observe this warning may result in serious injury from flash fire and/or electrical shock.   first aid: swallowed – not considered a normal route of entry. do not induce vomiting. seek medical advice. avoid giving milk or oils. avoid giving alcohol. skin – flush skin and hair with running water (and soap if available). remove any adhering solids with industrial skin cleansing cream. do not use solvents. seek medical attention in the event of irritation.

Features of NDT 101 Non Destructive testing Detects Surface defects upto 1 micron width x 30 micron depth on Standard Ni - Cr Test Panel. Low halides and Sulphate contents. Non - corrosive and non - toxic. The quick opertional sequence makes results available immediately. Convenient and easy to handle pressurised cans and bulk containers to suit various industrial needs. A General purpose, verstile and inexpensive technique.   Environment friendly CLEANER SPRAY- is an aerosol applied cleaner used as part of the NDT crack detection system for pre-use cleaning, also for the easy removal of ASS RED DYE and ASS DEVELOPER Sprays. Cuts through dirt, grease and grime Zero residue Prepares surface for non destructive testing   DEVELOPER SPRAY-is an aerosol applied white powder that is designed to draw the penetrant out of a flaw to enhance the definition. It is used to facilitate detection when used in conjunction with the NDT crack detection system. Highly absorbent white film for rapid results Highlights very fine cracks Sharp indication and geometry of defect to the naked eye Suitable for pressure testing & leak detection   DYE PENETRANT SPRAY - Dye Penetrant is an aerosol applied dye which can be sprayed from any angle. Used as part of the NDT crack detection system. Bright red even film Highly sensitive dye Water washable   Application of NDT 101 Non Destructive testing Non-destructive inspection system is designed to provide a fast reliable method for visual detection of cracks or flaws which would not normally be visible to the naked eye. Ideal for the inspection of welded joints, castings, forgings etc. non-destructive testing kit includes the cleaner, penetrant and developer spray in a convenient carrypack. Cleaner : Stainless Steel,Titanium,Nickel,Carbides,Ceramic and certain plastics,Pressure,Vessels,Pipelines,Heat Exchangers,Casting and Forgings. Developer :Aluminum,Magnesium,Brass,Copper,Cast Iron,Steel,Pipelines,Heat,Exchangers,Casting and Forgings,Petrochemical plants,Boilers. Dye Penetrant : Pressure Vessels,Pipelines,Heat Exchangers,Casting and Forgings,Petrochemical plants,Boilers and others   Direction of use of NDT 101 Non Destructive testing Shake well before use. Clean the surface to removed dust with clean cloth. Hold the can at least 8 to 12 cm from the surface you are spraying and keep the can upright during use. repeat the same every after every 8-10 operations. wipe off the spatter with a light cloth. When finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes   Precaution of NDT 101 Non Destructive testing Contents are Extremely Flammable and Under Pressure, Do Not Puncture Prevention : Keep away from heat, sparks, open flames, hot surfaces. No smoking. Avoid breathing dust, fume, gas, mist, vapours, spray. Use only outdoors or in a well-ventilated area. do not contaminate water supply. incinerate or store above 50°C. Exposure to high temperatures may cause can to burst. Do not place in direct sunlight or near any heat source. Aerosol cans will conduct electricity. Keep away from all live electrical sources including battery terminals, solenoids, electrical panels and other electronic components. Failure to observe this warning may result in serious injury from flash fire and/or electrical shock.   First Aid : Swallowed – Not considered a normal route of entry. Do not induce vomiting. Seek medical advice. Avoid giving milk or oils. Avoid giving alcohol. Skin – Flush skin and hair with running water (and soap if available). Remove any adhering solids with industrial skin cleansing cream. 

Features of BTC 2021 Battery Terminal Coat Protector Dry BTC 2021 Battery Terminal Coat Protector Dry is designed to protect battery terminals from corrosion, the leading cause of battery failure, and to maintain the batteries peak performance level. Battery Terminal Protector provides a dry, lead- free protective coating that keeps moisture, salts and road grime from corroding metal contacts. Maximises performance, provides long lasting protection and extends battery life.   Application of BTC 2021 Battery Terminal Coat Protector Dry Protecting battery and cable terminals against leakages, acid sulfation and corrosion. Prevents current losses and enhances battery life Air tight, water proof and acid resistant, anti-sulfation coating. Resistant to heat, gasoline, oil & grease, will not crack or peel when correctly applied on undamaged batteries operating in conditions of medium acidity.   Direction of BTC 2021 Battery Terminal Coat Protector Dry Shake well can before use. Disconnect earth cable to prevent arcing before applying. Clean away any existing corrosion with RMC 00 Battery Maintenance. Apply an even coat of RMC 00 Battery Terminal Protector to freshly cleaned site. For preventative maintenance, reapply at least every four months. When finished spraying, clean valve by turning can upside down and depressing actuator until only propellant escapes. Do not use on energized equipment. Do not allow can to touch battery terminals.   Precaution of BTC 2021 Battery Terminal Coat Protector Dry Contents are Extremely Flammable,Contents Under Pressure, Do not punctured. Prevention : Keep spray away from heat, sparks, pilot lights, open flames, etc. Do not place in direct sunlight or near any heat source. Aerosol cans will conduct electricity. Keep away from all live electrical sources including battery terminals, solenoids, electrical panels and other electronic components. Failure to observe this warning may result in serious injury from flash fire and/ electrical shock. Harmful by inhallation and avoid contact with skin and eyes Response : IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. Disposal requirements vary by state and local regulations. All used and unused product should be disposed of in conformance with local, state and commonwealth laws and regulations.   Storage of BTC 2021 Battery Terminal Coat Protector Dry Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50°C/122 °F. Store in a well-ventilated place.keep container tightly closed. Keep Out of Reach of Children

Application : Electrical Industry

Shelf Life : 1 Yr

Form : Liquid

Packaging Type : Tin Can

Packaging Size : 400 ml

Features of BPS 4536 Battery Protector And Sealer BPS 4536 Battery Protector & Sealer is an aerosol product for sealing and coating the terminals of a battery and eliminating the formation of acid salt corrosion that is typically found when terminals are untreated. Battery Protector is designed to protect battery terminals from corrosion, the leading cause of battery failure, and to maintain the batteries peak performance level. Battery Protector provides a dry, lead-free protective coating that keeps moisture, salts and road grime from corroding metal contacts. It maximises performance, provides long lasting protection and extends battery life. Prevents battery drain  Improves electrical flow   Application of BPS 4536 Battery Protector And Sealer Battery protector used in Batteries Cables Terminals   Direction of BPS 4536 Battery Protector And Sealer Product should be sprayed in a well-ventilated area. Clean parts to be treated with RMC Battery Cleaner Shake can with ball agitator for one minute. For best results, aerosol can should be at room temperature before spraying. Holding can 8 to 10 inches from the surface to be coated, press the nozzle and discharge the product onto the terminal areas. The product discharges as a heavy film. 5. For best results, apply two light coats.   Precaution of BPS 4536 Battery Protector And Sealer Contents are Extremely Flammable and Under Pressure, Prevention Avoid breathing dust/fume/gas/mist/vapors/spray Use only outdoors or in a well-ventilated area Wash face, hands and any exposed skin thoroughly after handling Wear protective gloves/protective clothing/eye protection/face protection Keep away from heat/sparks/open flames/hot surfaces. – No smoking Do not spray on an open flame or other ignition source Pressurized container: Do not pierce or burn, even after use Precautionary Statements – Response If exposed or concerned: Get medical advice/attention Specific treatment (see supplemental first aid instructions on this label) If in Eyes : Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing If eye irritation persists: Get medical advice/attention If skin irritation occurs: Get medical advice/attention If On Skin (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower Wash contaminated clothing before reuse If Inhaled : Remove victim to fresh air and keep at rest in a position comfortable for breathing If Swallowed: Immediately call a POISON CENTER or doctor/physician Do NOT induce vomiting. Dispose of contents/container to an approved waste disposal plant   Storage of BPS 4536 Battery Protector And Sealer Products shall be ideally stored in a cool, dry location in unopened containers at a temperature between 8_ to 28_C (46_ to 82_F) unless otherwise labeled. Optimal storage is at the lower half of this temperature range. Store locked up. Protect from sunlight. Store in a well-ventilated place.keep container tightly closed. Keep Out of Reach of Children

Shelf Life : 1 Yr

Form : Liquid

Packaging Type : Can

Packaging Size : 400 ml

features of btc 2021 battery terminal coat protector dry btc 2021 battery terminal coat protector dry is designed to protect battery terminals from corrosion, the leading cause of battery failure, and to maintain the batteries peak performance level. battery terminal protector provides a dry, lead- free protective coating that keeps moisture, salts and road grime from corroding metal contacts. maximises performance, provides long lasting protection and extends battery life.   application of btc 2021 battery terminal coat protector dry protecting battery and cable terminals against leakages, acid sulfation and corrosion. prevents current losses and enhances battery life air tight, water proof and acid resistant, anti-sulfation coating. resistant to heat, gasoline, oil & grease, will not crack or peel when correctly applied on undamaged batteries operating in conditions of medium acidity.   direction of btc 2021 battery terminal coat protector dry shake well can before use. disconnect earth cable to prevent arcing before applying. clean away any existing corrosion with rmc 00 battery maintenance. apply an even coat of rmc 00 battery terminal protector to freshly cleaned site. for preventative maintenance, reapply at least every four months. when finished spraying, clean valve by turning can upside down and depressing actuator until only propellant escapes. do not use on energized equipment. do not allow can to touch battery terminals.   precaution of btc 2021 battery terminal coat protector dry contents are extremely flammable,contents under pressure, do not punctured. prevention : keep spray away from heat, sparks, pilot lights, open flames, etc. do not place in direct sunlight or near any heat source. aerosol cans will conduct electricity. keep away from all live electrical sources including battery terminals, solenoids, electrical panels and other electronic components. failure to observe this warning may result in serious injury from flash fire and/ electrical shock. harmful by inhallation and avoid contact with skin and eyes response : if inhaled: remove victim to fresh air and keep at rest in a position comfortable for breathing. call a poison center or physician if you feel unwell. if in eyes: rinse cautiously with water for several minutes. remove contact lenses, if present and easy to do. continue rinsing. if eye irritation persists: get medical attention. disposal requirements vary by state and local regulations. all used and unused product should be disposed of in conformance with local, state and commonwealth laws and regulations.   storage of btc 2021 battery terminal coat protector dry store locked up. protect from sunlight. do not expose to temperatures exceeding 50°c/122 °f. store in a well-ventilated place.keep container tightly closed. keep out of reach of children

Features of ZC 678 Anti corrosion Bright zinc coating is Inhibits rust and corrosion on ferrous metals. Stops rust and corrosion on any iron or steel surface, Provides the appearance of a hot-dip galvanised, Highly resistant to scratching, denting, abrasion, corrosive environments, salt air, heat, moisture and road salts. Quick-drying Non-sagging touch-up of damaged galvanising Its galvanic action ensures better self-healing and sealing   Application of ZC 678 Anti corrosion Bright zinc coating Bright-Zinc is the original metallic silver colour zinc-rich coating that has been used on towers, power generators, farms, fencing ,Air conditioning equipment / ducts, satellite, antennas. It is used as an anti rust primer on vehicle bodies.It forms a protective coating on welded and drilled section. Used in Marine works and ship manufacturing parts and repairing. also used in heavy equipment, pipes, transformers, electrical poles, threads, welds, automobile, Metal chain fences, storage tanks etc. They are invaluable for use in : Construction Agriculture, Local authorities, Railway, Welding, transport, Automotive, Engineering,   Direction of ZC 678 Anti corrosion Bright zinc coating Surface should be dry and free of rust bloom. Shake well until agitator ball is free. Repeat while using. Best results are obtained when sprayed above 60º F. Spray from 12-15 inches away in light, even coats. The optimum film thickness for Bright Zinc is 1.5 to 3.0 mils of dry film. To obtain this thickness via aerosol application, 3 passes of spray are required. Spray the substrate once vertically, once horizontally, and once more vertically for ideal coverage. Additional coats for heavy film can be applied when first coat is dry. For a thickness of 3 mils, repeat the above spray pattern twice. When finished spraying, clean valve by turning can upside down and pressing button until only pressure escapes. If clogging occurs, remove button and clean slot and orifice with fine wire.   Precaution of ZC 678 Anti corrosion Bright zinc coating Contents are Extremely Flammable and Under Pressure. Do not punctured , may explode if heated. Do not apply while equipment is energised, Keep away from all live electrical sources including battery terminals, solenoids, electrical panels and other electronic components. Prevention : Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurised container: Do not pierce or burn, even after use. Do not spray on an open flame or other ignition source,live circuits. Harmful in contact with eyes. Prolonged exposure may cause chronic effects. May cause drowsiness and dizziness Response : IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTRE or physician if you feel unwell. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.   Storage of ZC 678 Anti corrosion Bright zinc coating Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50°C/122 °F. Store in a well-ventilated place. Keep container tightly closed. Keep Out of Reach of Children.

Color : silver

Features of ACC 2010 Acrylic Conformal Coating ACC 2010 Acrylic Conformal Coating is a flexible transparent acrylic coating for the protection of electronic circuitry formulated to meet the highest resistance requirements. Used on printed circuit boards as protective coating against moisture, dust, humidity and fungus. Protects all Electrics/Electronics Circuitry equipments in Extreme Service Environments. Excellent adhesion and dielectric properties. Good moisture resistance & Quick Evapouration.   Application of ACC 2010 Acrylic Conformal Coating It used as extra/after insulation of coils and transformers and reduces operational noise. Military Equipment Aerospace Industry Air Conditioner Circuit Board Industrial Applications Automotive Applications   Direction of ACC 2010 Acrylic Conformal Coating Shake well can before use at least 1 Minutes.Hold the can at least 15 to 20 cm from the surface you are spraying and keep the can upright during use. Protect & Mask areas not Coated. Two light coats is best results better than one heavy coat.Coating becomes dry in 20 minutes. make sure the surface is completely dry before using. completed cure takes place in about 24 hours depends upon the humidity. When finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes.   Precaution of ACC 2010 Acrylic Conformal Coating Contains gas under pressure do not punctured ,may explode if heated. Extremely flammable aerosol. Prevention : Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurized ontainer: Do not pierce or burn, even after use. Do not spray on an open flame or other ignition source. Use only outdoors or in a well-ventilated area. Avoid breathing vapor. Wash hands thoroughly after handling. Causes serious eye irritation. May cause drowsiness and dizziness Response : IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.   Storage of ACC 2010 Acrylic Conformal Coating Storage : Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F. Store in a well-ventilated place.keep container tightly closed. Keep Out of Reach of Children

Brand Name : ASS

Shelf Life : 1Year

Country of Origin : India

Usage : Industrial Use

Features of ACC 2010 Acrylic Conformal Coating ACC 2010 Acrylic Conformal Coating is a flexible transparent acrylic coating for the protection of electronic circuitry formulated to meet the highest resistance requirements. Used on printed circuit boards as protective coating against moisture, dust, humidity and fungus. Protects all Electrics/Electronics Circuitry equipments in Extreme Service Environments. Excellent adhesion and dielectric properties. Good moisture resistance & Quick Evapouration.   Application of ACC 2010 Acrylic Conformal Coating It used as extra/after insulation of coils and transformers and reduces operational noise. Military Equipment Aerospace Industry Air Conditioner Circuit Board Industrial Applications Automotive Applications   Direction of ACC 2010 Acrylic Conformal Coating Shake well can before use at least 1 Minutes.Hold the can at least 15 to 20 cm from the surface you are spraying and keep the can upright during use. Protect & Mask areas not Coated. Two light coats is best results better than one heavy coat.Coating becomes dry in 20 minutes. make sure the surface is completely dry before using. completed cure takes place in about 24 hours depends upon the humidity. When finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes.   Precaution of ACC 2010 Acrylic Conformal Coating Contains gas under pressure do not punctured ,may explode if heated. Extremely flammable aerosol. Prevention : Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurized ontainer: Do not pierce or burn, even after use. Do not spray on an open flame or other ignition source. Use only outdoors or in a well-ventilated area. Avoid breathing vapor. Wash hands thoroughly after handling. Causes serious eye irritation. May cause drowsiness and dizziness Response : IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.   Storage of ACC 2010 Acrylic Conformal Coating Storage : Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F. Store in a well-ventilated place.keep container tightly closed. Keep Out of Reach of Children

Type : Conformal Coating, Industrial Automation

Form : Liquid

Brand Name : ASS