Brake Parts Dealers in Airoli, Navi Mumbai

• Brand Name: ASS
• Pack Size: 720ml
• Pack Type: Tin Bottle
• Form: Liquid
• Shelf Life: 1 Year

Features of HD 1015 - Heavy Duty Mechanical Parts Cleaner Heavy Duty Parts Cleaner is designed to penetrate and effectively dissolve and remove oil, grease, brake fluid, and other soils from all metal parts, heavy machinery, farming equipment, mining equipment, and any other mechanical parts in extremely difficult situation. Low odour properties improve operator working conditions.Will quickly and effectively flush built up grease from chains and slides on forklifts, wire ropes and all types of industrial equipment.   Application of HD 1015 - Heavy Duty Mechanical Parts Cleaner The product is designed to be effective in heavy duty cleaning of machine parts, disc & drum brakes and forklift chains, wire ropes, open gears, bearings, valves, sprockets etc.   Direction of HD 1015 - Heavy Duty Mechanical Parts Cleaner Shake well before use until the sound of the ball is audible. clean & degrease surface Hold the can at least 10 to 12 cm from the surface you are spraying and keep the can upright during use.Protect & Mask areas not Coated. Two light coats is best results better than one heavy coat.Coating becomes dry in 20 minutes. make sure the surface is completely dry before using.completed cure takes place in about 24 hours depends upon the humidity. & maintain full pressure on valve while spraying. Repeat spraying whenever necessary. When finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes.   Precaution of HD 1015 - Heavy Duty Mechanical Parts Cleaner Contains gas under pressure do not punctured ,may explode if heated. Extremely flammable Prevention : Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurized container: Do not pierce or burn, even after use. Do not spray on an open flame or other ignition source. Use only outdoors or in a well-ventilated area. Avoid breathing vapor. Wash hands thoroughly after handling. Causes serious eye irritation. May cause drowsiness and dizziness Response : IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.   Storage of HD 1015 - Heavy Duty Mechanical Parts Cleaner Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50°C/122 °F. Store in a well-ventilated place.keep container tightly closed. Keep Out of Reach of Children

• Meets Industry Standards: MIL-PRF-5606, MIL-PRF-83282 and MIL-PRF-87257
• Weight (lb): 0.32 to 1.05
• Housing Material: Aluminum
• Displacement (cu in/rev): 0.42 to 1.015

Master cylinders are located in the cockpit on each of the pilot’s rudder pedals. They are used to turn a force into a pressure to actuate the brakes on an aircraft. By integrating the reservoir directly into the master cylinder housing, Parker has eliminated the need for a separate, remotely mounted reservoir. There are several advantages to this fewer fittings translates into fewer possible leak paths and the elimination of the need to find a remote location for a reservoir in a space-limited aircraft. This also means there are fewer parts to inspect and maintain, no need for a hydraulic line between the remote reservoir and the master cylinder, and weight savings. Parker offers a version with a reservoir designed into the cylinder. It eliminates the need for a remote reservoir located in the firewall area, giving easier control over the system and less line from the brake assembly. The reservoir capacity ranges from 2 to 3.4 cubic inches with strokes from 1.2 to 1.75 inches. Total volumetric output is 0.36 to 0.77 cubic inches. Ports are 18-27 NPT thread, which is common in the general aviation market.

Press Brake Dies tools are designed applying modern sciences and techniques. Press Brake Dies are three tools’ types found such as hemming tools, wiping tools, and forming tools. To develop such Press Brake Dies the die types involved are single vee die block, 2 vee die block, and multi vee die block. In addition, these tools are built and developed adhering to industry standards and following entire quality norms. Furthermore, the offered tools are made available at industry leading rates.Accurate and aligned processing,Wide industrial use,Custom design available

We are offering brake drums, couplings. brake drums are made from rolled bar or cast steel. the brake dums are fully machined to eliminate vibration. brake drums are dynamically balanced after machining when required by cutomer. the drum surface is treated to achieve high hardness for longer life.

Brake Drums, Hook Block, Rope Drum, Wheel Assembly, Planetary Gears

drum brake shoe, Asbestos Products, railway brake block

• Phase: Single Phase
• Power Source: AC
• Feature: Flange Mounted, Foot Mounted Fitted with DC Brake
• Torque Range: 4NM to 360NM

Transformer

break liner, Two Wheeler Spare Parts, Clutch Plate, Horn, Gear

Nylon Seat Belts, roller bush, winch drum, Nylon Hair Belt, fiber bush

Cable

Cable, Industrial Paints, industrial switch, industrial nut bolts, Wire

press brake dies, Shearing Blades, Plano Miller Job Work, surface grinding

transformer insulation parts, core, connection