Braking System Dealers in Ghansoli, Navi Mumbai

• Brand Name: ASS
• Pack Size: 720ml
• Pack Type: Tin Bottle
• Form: Liquid
• Shelf Life: 1 Year

Features of HD 1015 - Heavy Duty Mechanical Parts Cleaner Heavy Duty Parts Cleaner is designed to penetrate and effectively dissolve and remove oil, grease, brake fluid, and other soils from all metal parts, heavy machinery, farming equipment, mining equipment, and any other mechanical parts in extremely difficult situation. Low odour properties improve operator working conditions.Will quickly and effectively flush built up grease from chains and slides on forklifts, wire ropes and all types of industrial equipment.   Application of HD 1015 - Heavy Duty Mechanical Parts Cleaner The product is designed to be effective in heavy duty cleaning of machine parts, disc & drum brakes and forklift chains, wire ropes, open gears, bearings, valves, sprockets etc.   Direction of HD 1015 - Heavy Duty Mechanical Parts Cleaner Shake well before use until the sound of the ball is audible. clean & degrease surface Hold the can at least 10 to 12 cm from the surface you are spraying and keep the can upright during use.Protect & Mask areas not Coated. Two light coats is best results better than one heavy coat.Coating becomes dry in 20 minutes. make sure the surface is completely dry before using.completed cure takes place in about 24 hours depends upon the humidity. & maintain full pressure on valve while spraying. Repeat spraying whenever necessary. When finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes.   Precaution of HD 1015 - Heavy Duty Mechanical Parts Cleaner Contains gas under pressure do not punctured ,may explode if heated. Extremely flammable Prevention : Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurized container: Do not pierce or burn, even after use. Do not spray on an open flame or other ignition source. Use only outdoors or in a well-ventilated area. Avoid breathing vapor. Wash hands thoroughly after handling. Causes serious eye irritation. May cause drowsiness and dizziness Response : IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.   Storage of HD 1015 - Heavy Duty Mechanical Parts Cleaner Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50°C/122 °F. Store in a well-ventilated place.keep container tightly closed. Keep Out of Reach of Children

• Phase: Single Phase
• Power Source: AC
• Feature: Flange Mounted, Foot Mounted Fitted with DC Brake
• Torque Range: 4NM to 360NM

• Material: Aluminum housing
• FEATURES: Weight optimized for each application • Robust design • Live technical support
• Weight: 5.29 to 35.80 lbs per brake assembly

Each multi rotor steel brake assembly is composed of one brake cylinder, one pressure-plate assembly with replaceable steel wear pads, two or more rotating discs (rotors) with sintered-friction material on a steel core, one or more stationary discs (stators) with replaceable wear pads, one torque-tube assembly with replaceable wear pads, along with necessary nuts, washers, and bolts.

• Design Limitations: 70,000 ft-lbs to 1,789,041 ft-lbs design landing KE
• Maximum Operating Pressure (psi): 500 psi to 1580 psi
• Size: 5, 6, 8, and 10-inch designs

The brake assembly and disc combination (part of the main wheel assembly) are designed and qualification tested to properly and safely decelerate the aircraft under various conditions. Unauthorized substitution of components can compromise brake effectiveness, is a violation of the qualification basis, and is prohibited. The brake assembly is an external floating caliper-type design and can be made of either cast magnesium or aluminum. The brake assembly consists of one or more pistons depending upon the aircraft requirements. A brake assembly can also consist of multiple calipers, one forward and one aft of the landing gear, and contain multiple pistons in each caliper. To actuate the brake assembly, hydraulic pressure, applied via the pilot’s and co-pilot’s master cylinders, enters the brake via lines connected to an inlet fitting on the caliper. The pressure then flows through the cylinder and forces the pistons outward against the pressure plate. The caliper should be free to slide on the torque plate assembly bushings allowing both pressure and back plate linings to contact the brake, which will contact the brake disc at precisely the same time. The braking action generates a torque which transmits a braking force converting the kinetic energy into heat, which is absorbed by the brake disc and surrounding components. This braking force is transmitted to the wheel and into the tire, bringing the aircraft to a stop. Releasing the toe pedal relieves the hydraulic pressure from the brake caliper, thereby removing pressure from the disc.

We are into manufacturing of press brake tooling since 1991,We offer wide range of press brake tooling. Varity of raw material is used to ensure quality as well as economy of tooling,3 variants as per international standard of tooling is offered,Hardened and ground tooling is our major forte,For maximum productivity we offer wide range to self centering die arrangements in single vee die, 2 vee die and multi-vee die block,We also offer forming tools, Radius tools, hemming tools.

Chlorhexidine Base, Hexamethylenediamine, Benzethonium Chloride

drum brake shoe, Asbestos Products, railway brake block

Brake Drums, Hook Block, Rope Drum, Wheel Assembly, Planetary Gears

transformer insulation parts, core, connection

These cables are used for low volatge Electrical power station, indoor or Outdoor,all kinds of Industrial Applications. Standards as per IS - 1554 (Part-1) Max. Conductor D.C. Resisitance at 200C conductor size 1.50 sq.mm - 12.1 Wkm (Bare) and 12.2 W km (Tinned copper) 2.50 sqmm - 7.41 Wkm (Bare) and 7.56 Wkm (Tinned Copper)

We are offering brake drums, couplings. brake drums are made from rolled bar or cast steel. the brake dums are fully machined to eliminate vibration. brake drums are dynamically balanced after machining when required by cutomer. the drum surface is treated to achieve high hardness for longer life.

Cable, Industrial Paints, industrial switch, industrial nut bolts, Wire

Cable

Automotive Seat, Bluetooth Speaker, Mobile Holder, Steering Wheel, steering

packed car shampoos

metal boxes, Metal Stamping, Wiper Blades

Clutch Plate, Two Wheeler Spare Parts, break liner, Horn, Gear

Transformer

Clutch Plate, electric bikes spares parts

press brake dies, Shearing Blades, Plano Miller Job Work, surface grinding