Braking System Dealers in Turbhe, Navi Mumbai

• Type: Electromagnetic Brake Motor
• Certification: CE Certified,ISO 9001:2008
• Power: 1-3kw,3-6kw,6-9kw,9-12kw
• Driven Type: Electric
• Phase: Three
• Current Type: AC,DC
• Speed: 1000-2000rpm,2000-3000rpm

• Brand Name: ASS
• Pack Size: 720ml
• Pack Type: Tin Bottle
• Form: Liquid
• Shelf Life: 1 Year

Features of HD 1015 - Heavy Duty Mechanical Parts Cleaner Heavy Duty Parts Cleaner is designed to penetrate and effectively dissolve and remove oil, grease, brake fluid, and other soils from all metal parts, heavy machinery, farming equipment, mining equipment, and any other mechanical parts in extremely difficult situation. Low odour properties improve operator working conditions.Will quickly and effectively flush built up grease from chains and slides on forklifts, wire ropes and all types of industrial equipment.   Application of HD 1015 - Heavy Duty Mechanical Parts Cleaner The product is designed to be effective in heavy duty cleaning of machine parts, disc & drum brakes and forklift chains, wire ropes, open gears, bearings, valves, sprockets etc.   Direction of HD 1015 - Heavy Duty Mechanical Parts Cleaner Shake well before use until the sound of the ball is audible. clean & degrease surface Hold the can at least 10 to 12 cm from the surface you are spraying and keep the can upright during use.Protect & Mask areas not Coated. Two light coats is best results better than one heavy coat.Coating becomes dry in 20 minutes. make sure the surface is completely dry before using.completed cure takes place in about 24 hours depends upon the humidity. & maintain full pressure on valve while spraying. Repeat spraying whenever necessary. When finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes.   Precaution of HD 1015 - Heavy Duty Mechanical Parts Cleaner Contains gas under pressure do not punctured ,may explode if heated. Extremely flammable Prevention : Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurized container: Do not pierce or burn, even after use. Do not spray on an open flame or other ignition source. Use only outdoors or in a well-ventilated area. Avoid breathing vapor. Wash hands thoroughly after handling. Causes serious eye irritation. May cause drowsiness and dizziness Response : IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.   Storage of HD 1015 - Heavy Duty Mechanical Parts Cleaner Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50°C/122 °F. Store in a well-ventilated place.keep container tightly closed. Keep Out of Reach of Children

We have well-maintained and capacious storage unit that includes all required facilities vital for a safe stacking of the products. We are working with experts and professionals and they supervise the range sternly ensuring zero damage to the stored items. We have a dedicated staff that ensures the quality of material used for designing and production. The inspection is done on the initial stages to make the final product free from defect. Our sturdy clutch plates are available in dimension 55x55x10cm. 

• Country of Origin: Made in India
• Brand Name: Green Power
• Model Number /Name: Gp Bmm-2L
• Height: 1050mm
• Width: 450mm
• Depth: 350mm
• Voltage: 230V
• Frequency: 50/60Hz
• Power During Operations: Max 18VA
• Temperature Range: -20 Deg C to +70 Deg C
• Operation: 1. Open Brake Oil Cup in vehicle’s Bonnet,2. Deep Insert White Suction Pipe in Brake Oil Cup,3. Make Machine’s Mains Switch ON and Put Suction Switch ON,4. Machine will start sucking Old Brake Oil from Cup and will put it in Waste Oil Tank at Rear sid

• FEATURES AND ATTRIBUTES:: Anodized housing – corrosion protection • Light weight • American made
• Weight (lbs): 0.45 to 1.5 lb
• Minimum Operating Temperature (F): -65° F
• Maximum Operating Temperature (F): 275° F

Pull-type master cylinders are an alternative to push-type master cylinders and are common in the general aviation market. Pull-type master cylinders are used when the aircraft’s linkage is not set up for a push-type master cylinder due to cockpit design constraints or the air framer’s preference. The aircraft’s linkage is set up to pull the rod of the master cylinder. This action is achieved when the pilot puts a foot on the brake pedal to stop the aircraft.

pneumatic brakes, Linear Actuators, motion control, thk linear motion guides

• Material: Mild Steel
• Color: Black
• Length: 18 inch
• Surface: Painted
• It's Rust Proof: Yes

Our loading docks to load and unload goods from trucks are well-maintained by the professionals; with completely automated warehouse that is sternly supervised. Thus, we make sure that products are kept safely. We ensure on time distribution of wholesale as well as retail consignments owing to an extensive vendor, distributor and logistic facility base.

• Pack Size: 300 gm (500 ml)

It thoroughly cleans disc and drum brakes, clutch components, adhesion and sealing surfaces of lining dust, oil, grease and dirt. Evaporates instantly leaving no residue. It is non-corrosive and non-staining.

We are specialist in different types of Cranes Brake linears. Like : Tata 320, 325, 440, 655, 955, TFC 955, 670, Link belt , American crane, 118 crane, Heavy duty Crane of capacity 800 tones.

• Phase: Single Phase
• Power Source: AC
• Feature: Flange Mounted, Foot Mounted Fitted with DC Brake
• Torque Range: 4NM to 360NM

Wire, Power Factor Correction Panel

Power Factor Correction Panel, Wire

Fine Chemical, Tetra Hydro Furan

These cables are used for low volatge Electrical power station, indoor or Outdoor,all kinds of Industrial Applications. Standards as per IS - 1554 (Part-1) Max. Conductor D.C. Resisitance at 200C conductor size 1.50 sq.mm - 12.1 Wkm (Bare) and 12.2 W km (Tinned copper) 2.50 sqmm - 7.41 Wkm (Bare) and 7.56 Wkm (Tinned Copper)

Manual Brake, Electric Brake, Magnetic Servo Clutches, Power Jacks

Clutch Plate, electric bikes spares parts

Heavy Vehicle Brake Parts

Disc Brake Parts

Clutch Plate, Automotive Axle, automotive shaft, Piston, Two Wheeler Parts

packed car shampoos

metal boxes, Metal Stamping, Wiper Blades

Electronic Component, polycab cable, Switch Gears, Wire

Automotive Seat, Bluetooth Speaker, Mobile Holder, Steering Wheel, steering

Industrial Lubricants, Motor Flush, Grease, Sealants, engineering adhesives

transformer insulation parts, core, connection