Control Panels Dealers in Rabale, Navi Mumbai

In industry, most of the load is inductive in nature which results in lagging power factor that is why there are loss and wastage of energy which results in high power bills and heavy penalties from electricity boards. If the load is uneven it is very difficult to maintain unity power factor. To overcome this difficulty apfc panel is used which maintains unity p.f. Features and applications : 1) high speed power factor correcting system is designed to compensate the reactive power of any load or equipment required p.f. Correction within one cycle of operating frequency or time delay of 30 sec to 5 min after command signal from apfc controller. 2) renders the distribution network more stable since there is no contactor switching causing high voltage transients, spikes, harmonics and other disturbances by applying zero crosses over voltage switching on and zero current switch off of the capacitors. 3) prevents voltage drop and flickering reduces failures in highly sophisticated electronic equipment like plcs. Computers and other control systems. 4) helps in reducing maximum demand and rkvah consumption hence a substantial reduction in monthly electricity tariffs. 5) it is highly suitable for spot welding applications where the reactive energy is to be compensated for a short period of 200 msec or less and for a number of times in a second. 6) accurate power factor control even in the presence of harmonics.

Pdb and apfc panels we manufacture low voltage power distribution boards (pdb), breaker panels, automatic power factor correction (apfc) panels, sub distribution panel, mcb db for different industries. Pdb panels are used for electric power distribution, fault protection and monitoring of different electrical systems. It usually consists of incomer acbmccb, switch fuse unit (sfu), elcb, mccb, mcb etc. Any electrical systems containing inductive & capacitive loads consumes both active and reactive power. Apfc panels are required to improve power factor of the entire plantfacility so that total power consumption (active + reactive) is minimized. It is usually achieved by means of capacitor banks which are switched on & off based on real time inductive loads such as induction motors. Nowadays apfc unit has become a necessity as many power distribution companies have started charging penalties in case of power factor drop beyond a limit. Salient features of our pdb & apfc panels are: compartmentalized acbmccb & apfc section expertise with mounting & wiring of different types of acbs mccbs upto 2000a capability of manufacturing apfc panels up to 1600a in house busbar cutting, busbar bending, sleeving facility user friendly enclosure design compliance to safety norms testing facility with 3-phase power supply upto ip 54 protection availabel being located in navi mumbai, our supplied panels are working not only in india but also in various countries like dubai, qatar, saudi arabia ksa, oman, kuwait and also in austria, germany, usa, australia, sri lanka, singapore, malaysia, vietnam, indonesia, india, nigeria, china, south korea, bangladesh, zambia etc

Along with high level of skilled designers & programmers we also lead with high level of skill fabricators to achieve some of the most complex CONTROL DESK to suit our customer’s requirement.   Features :- Available in Floor mounting type. Degree of Protection :-IP-52 to IP-65. Painting: - Powder Coating, Spray Paint, Epoxy Paint. Compartmentalized design. Designed to accept 3-phase, 4 wire input volt. Provided with buzzer & hooter during emergency. Provided with 12/24 window annunciator for fault indication.    Application :-   These are widely used for :- »  Control & monitoring of various electrical motors, loads etc. of an electrical system. »  Protect against various electrical faults. »  Better & smooth trouble free electrical life of various electrical machines. »  Control Desk may save energy of an electrical system.

We are well known manufacturers as we deal with electrical devices that are immensely important in the day to day industrial life. They are fabricated in such a manner that they impart all the functional properties in a definite manner.

• Ratings range: 63A up-to 400A

Drawout Panel Accessories With drawable panel accessories are in direct contact with the vertical bus-bars. The power contacts are available in ratings from 63A up-to 400A. The Power contacts are tested from mill-volt drop & temperature rise at C.P.R.I. Laboratories. Sunesons has recently developed a new set of main power contacts with a swivelling rear link, which makes it convenient for use in power feeders that have bus bar connections to be made between the pore contact & the switchgear. These contacts are available in a ratings of 100A to 630A. They are tested for mill-volt drop & temperature rise at C. P. R. I laboratories. Spring-loaded, tinsilver plated main power contacts are provided for both the incoming as well as outgoing side main circuit connections. Drawout Panel Accessories With drawable panel accessories are in direct contact with the vertical bus-bars. The power contacts are available in ratings from 63A up-to 400A. The Power contacts are tested from mill-volt drop & temperature rise at C.P.R.I. Laboratories. Sunesons has recently developed a new set of main power contacts with a swivelling rear link, which makes it convenient for use in power feeders that have bus bar connections to be made between the pore contact & the switchgear. These contacts are available in a ratings of 100A to 630A. They are tested for mill-volt drop & temperature rise at C. P. R. I laboratories. Spring-loaded, tinsilver plated main power contacts are provided for both the incoming as well as outgoing side main circuit connections.

Type tested to conform to leading Global Product Standards. (IEC-61439-1 & 2). Fully Compartmentalized (Form IV) Design. Drawout modules are simply pushed in for withdrawal, ensuring smooth & tool-less operation. Drawout modules plug-in directly on to Vertical Bus Bar, minimizing maintenance issues. Vertical Bus is Joint-free along the feeder area, therefore is highly reliable. Safety shroudshutter providing IP 20 levels of segregation upon withdrawal. Shock-free operation with Double Stab-in earthing in all Drawout modules. Fully Bolted Modular Structural design. Drawout Modules have interlocks for Test, Service & Isolated positions. Drawout Modules available in 3 Pole for Starter feeders & 4 Pole for Power feeders.

We manufacture, supply and export a complete range of Control Panels. Fabricated using high grade components, these control panels strictly conform to the international quality standards. Owing to such our streamlined production process, we ensure that these control panels are superior in quality and functionality, due to which these have a high demand in the global market. Our valued clients can avail this range from us at industry leading prices.

  programmable logic controller(PLC) is an electronics device which is used for automation purpose's.in industry PLC is used for automation purpose's such as control of machinery.in comparison to general purpose computer's PLC has various advantages like immunity to noise,less effect of vibration,can work in dusty conditions and extended temperature range.

Control Panel for EOT cranes manufactured by Silverline Metal Engineering Pvt. Ltd. are used to facilitate crane drivers in smooth operations of cranes during various operation.

• Width: 1000mm

It can give you multiple benefits including applying it over the roof as well as under roof insulation. The process of applying insulation material is comparatively easy as most of the housing roof as well as industrial ceilings have some access for caring insulation work. Apart from temperature or thermal insulation and upholding your premises or industry in better climate condition in higher temperature, low cost is another advantage why the popularity of roof insulation is increasing. One can apply as much as insulation to make it thicker and more thermal barrier as there are very little difference on the overall cost. Apart from temperature conversation and heat resistance, roof insulation material also gives helping hand to your pocket. It also saves money because every bit of loss in temperature can result into to higher energy consumption and higher expense.

Conventional Traditional fire alarm panels installed prior to 1998 were conventional zone panels. In a zoned system, fire alarm devices in a common area or floor of a facility are connected to the same alarm initiating circuit. Each zone requires its own circuit conductor. This arrangement allows alarm annunciation to be reported by areas of the building to identify which device is in alarm. Conventional panels are often used in small facilities where a few zones can provide sufficient alarm annunciation.  Addressable With the advent of microprocessors and digital electronics, addressable fire alarm control panels and devices have become more common than conventional systems for medium and large-sized facilities. They have become more cost effective in some small applications as well. Addressable fire alarm systems use digital encoding and multiplex technology to more accurately identify alarm locations and device conditions. Each fire alarm device in a system is programmed with a unique address. The fire alarm control panel is capable of communicating with a single address or a group of addresses depending on the functions required. The communication is often multiplexed over a common cable, sometimes referred to as the signaling line circuit (SLC). This arrangement significantly reduces the amount of cabling necessary to install the system. The communication channel allows two-way communication, thus enabling the fire alarm control panel to control as well as monitor fire alarm devices. A significant component of addressable fire alarm system is the software programming necessary to make the system function correctly. The programming allows for flexible applications where you want to have specific control over the inputs and outputs. The communication technologies employed in addressable systems allow for advanced features to accommodate sensitivity changes due to age and accumulation of dust prior to maintenance. These features are not available with the standard conventional system.   Fire Alarm Devices Automatic Detection Components of a fire consist of: Smoke (particulate and aerosol) Heat Light Radiation Fire detection devices are built to detect one or a combination of these components. While all components are necessary for a fire to exist, all components may not exist at a detectable threshold. Detectors will be selected that will detect the elements that may exist in a fire for the ambient conditions that are present. It also should be realized the similar non-fire components might exist in the same ambient conditions, which could cause unfavorable false alarm conditions. Devices used for fire detection include smoke detectors, thermal detectors, flame detectors, fire-gas detectors, and other devices. Smoke detectors sense visible or invisible particles of combustion generated by burning, smoldering, or the incipient stage of combustion. These devices fall into two categories -- photoelectric and ionization. Thermal detectors sense the high temperature or the temperature rise caused by a fire. Flame detectors sense the radiation produced by a fire. Fire-gas detectors sense the gases produced by a fire. Other detectors sense some phenomenon other than smoke, thermal, flame, or fire-gas to detect a fire. Smoke Detectors There are three types of smoke detectors: Ionization, photoelectric, and combination.   Ionization The ionization smoke detector is widely used. Its capability to detect smoke originating from fire is best utilized for clean-burning fires that produce small particles during combustion.   The ionization smoke detector consists of an alpha particle producing a radioactive source, a smoke chamber, and charged detector plates. The alpha source causes the air within the smoke chamber to become ionized and conductive As smoke particles enter the smoke chamber, the smoke particles attach themselves to the ionized air molecules and the air in the chamber becomes less conductive When the air conductivity within the chamber drops below a predetermined level, the alarm is triggered Advantages of Ionization Smoke Detectors: Detects invisible products of combustion -- It can detect fires that are in the incipient stage or detect other aerosol-type smoke products Quick acting -- Provides for earlier detection than other types of smoke detectors or thermal detectors

• Automation Grade: Semi-Automatic
• Material: steel
• Power Source: Electric
• Voltage (V): 220
• Power (Kw): 5
• Frequency (Hz): 50
• IP Type: IP45
• Surface Treatment: Polished

Supported by a well-organized network and dependable resources, we have developed as a reputed supplier of Flameproof Control Panel. Serialization is done before the final packaging and storing of the products in our capacious warehouse. We keep the products separated to ensure rapid delivery in the committed time span.   Specifications : Power Rating : Variable Phase : Single Phase / Three Phase Frequency : 50 Hz Material of Construction : Aluminum LM6 Type of Protection : Flameproof Ex'd. Zone classification : Zone 1 & Zone 2. Gas Group : IIA,IIB, T6. Fault Indication : LCD/LED. Dimensions : as per Requirement. Usage : Motor Control , Drive Control , Power Control.

With the support of our competent procurement teams, we source and export a quality range of Electrical Panels. Using advanced and modern technology, these panels are manufactured from high quality factor inputs under the supervision of our experienced team of professionals. To get maximum satisfactions of our clients, our offered panels are tested with all quality parameters of the international standards. These panels are highly useful to avoid short circuit or overload. Apart from this, our offered panels are widely appreciated for their excellent features like durability, sturdy construction and reliability. With the help of our professionals, Dewdry Industries is capable in offering an exclusive array of Dehumidifier Control Panel. Offered panels are designed & developed by the experts in complete compliance with the international quality standards. Apart from this, these panels are strongly constructed to prevent damages and all useless electrical defaults. Available with us in various designs, these panels are highly known for their durability and sturdy construction. We offer these panels at effective rates. Features: Excellent performance Durable Low power consumption

• Phase: Three Phase
• Material: Mild Steel
• Voltage: 220-440 V
• Finishing: Coated
• IP Rating: IP 44
• Frequency: 50-60 Hz

We are offering gas monitoring control panel. The three models in the gasmaster range all provide two levels of rising or falling alarms for each channel; individual fault and alarm indicators; outputs for annunciators, shutdowns, dedicated audiblevisual alarm drive and datalogging; ac and dc power options, and battery backup. gasmaster : gasmaster 1 offers a single channel of gas detection and has been especially designed for areas such as light industrial units, boiler rooms and catering areas. gasmaster fp : gasmaster-fp includes all the features of gasmaster-4, but within a specialist casing, which is certified flameproof. Gasmaster 4 with the flexibility of four channels, gasmaster-4 can control both gas and fire detectors and also specialist detectors such as our environmental sampling unit (esu), making gasmaster 4 the ideal control panel for industrial applications

• Features: Excellent quality, Robust, Easy installation, Highly efficient

It is Metal clad type & having type tested design suitable up to 400KV switchyards It is equipped with Siemens, Areva & CSPC protective relays along with MIMIC presentation.

We are supplying products like as Electrical Control Panels

The Power Command Control is a microprocessor based generator set monitoring, metering, protection and control system. It offers advanced levels of functions for reliability and optimum genset performance.The power command control with digital paralleling control devices such as synchronizers and load sharing controls, and KVAR / Power factor controls.         Vesta Engineering is a Mumbai based company. Presently engaged in design, manufacturing & supply and installation of power panels, control panel, feeder pillars etc.         Manufacturers & suppliers of electrical Control Panels that include PLC Panel, AC Drive Panel, DC Drive Panel, LT Panel, PCC/MCC Panel, APFC Panel, AMF Panel, Generator Control Panel.       We manufacture and supply our high-quality products to cater to our client's requirements.     Our panel boards are made under strict supervision by qualified personnel. Very strict quality control is exercised on the production lines while the components and other raw materials used are of the best quality available   Its Types     1. A.M.F Control Panel 6. PCC Control panel Control (PCC)     2. Synchronizing Panel 7. ACB Panel     3. D.G. Set STD Control Panel 8. APFC Panel     4. Power Dist. Board (PDB) 9. MCC Panel     5. Change Over Panel Boards 10. RELAY Panel