Meco Instruments Pvt Ltd TTC Industrial Area, Navi Mumbai, Maharashtra

MECO AC Voltage Transducer measures AC Voltage and converts it to an industry standard output signal which is directly proportional to the measured input. These Transducers provide an output which is load independent and isolated from the input. The output can be connected to Controllers, Data-Loggers, PLC's, Analog Digital Indicators, Recorders for display, analysis or control. They are ideal for SCADA, Energy Management, Telemetering for Remote, Local as well as Central Monitoring Systems.

TRMS Measurements, Measures V, A, Hz, Run, Hour, On Hour and RPM, RUN Hour On Hour (Max.99999 Hours, 59 Minutes, 59 Seconds), RUN Hour On Hour Reset Facility, Auto Scroll Manual Scroll Display, 3 Phase 4 Wire, 3 Rows of 3 Digits Super Bright Red LED Display, Programmable CTR, PTR, Number of Pole Setting, Auto Indication for 'KV' and 'KA', Auto Selection of Decimal Point

6½ Digit Display (11,99,999 counts) 12 Different Measurement Capabilities ; DCV ACV, DCI ACI, Ω2W Ω4W, Frequency Period, Diode Test, Continuty, dB dBm High brightness vacuum fluorescent display True-rms AC voltage and current measurement, bandwidth up to 300kHz DCV measurement accuracy up to 0.0035%, resolution up to 0.1μV Max. measurement rate : 1000 meas sec Equal accuracy frequency measurement up to 1.1 MHz Relative mode (REL) to eliminate residual reading 2W, 4W resistance measurement mode selectable Built-in mX +b, %, dB, dBm etc mathematics calculation function 512 reading storage and MAX MIN AVER STD statistics Up to 30,000 readings storage (without statistics) HI IN LO comparator function USB, BPIB and RS-232 Interfaces provide easy system communication Calibration without opening the case 10 sets of multimeter setup can be stored and loaded

Calibration of AC Volt, Amp, Frequency Meters, Calibration of DC Volt, Amp Meters, Calibration of Resistance Meters, Insulation Testers, Step adjustment of Output Signal : 10 %FS, 1 %FS, 0.1 %FS, 0.05 %FS

Transformer is a very important Element in the Electric Power Distribution System. It needs to be maintained from time to time to Guarantee Smooth Power Supply at Consumer end. MECO TTR8100 is Portable instrument for accurate measurement of 1-Phase & 3-Phase Transformer VT CT Turned Ratio, Excitation Voltage, Current, Phase Angle and Deviation. TTR8100 ensure the Correct Turn Ratio & Quality of the Transformer. It Check Live Test Point, Short Circuit, Open Circuit and Revers Polarity before each measurement.

Digital Multimeters Digital Clampmeters Analog & Digital Insulation Testers Leakage Current Tester and Clamp-On Earth / Ground Resistance Tester Micro - Ohmmeter / Milli - Ohmmeter LCR Meter

Max. solar system power (Pmax) search by Auto-scan: 1000V, 12A (12000W capability), The analyzer and the Remote Solar Detector is connected by Bluetooth wireless communication (Bluetooth 2.1 + EDR Class 1), The Remote Solar Detector is moisture-proof, Intelligent test logic with no personnel attendance required in the field, Solar system analyzer waits and tests the system until appropriate sunlight irradiance is detected, Max. voltage (Vpm) at Pmax, Max. current (Ipm) at Pmax.

We are supplying products like as SPLIT CORE CURRENT TRANSFORMERS

This instrument is designed to measure Solar Power in the range from 400 to 1100 nanometers. The good Spectral Range, Orientation and Angular detection of meter allow users to conduct the most precise quantitative measurements of Solar Power Radiation, Solar Power Measurement with Orientation and Tilt Angle.

We are one of the famous company, who are manufacturer of solar analyzers.

Current Measurement, Monitoring and Protection for Electrical Wiring and Equipment, Current and Power Measurement for Electric Motors, Lighting, Air Compressor, Heating and Ventilation System, Air - Condition Equipment and Automation - Control System, Current, Power and Energy Monitoring Device, Relay Protection Device, Wide Inner Window, Allowing Clamping of Big Cables or Bus - Bar, Clamp - On Design, Fastening Safe, Easy to Install, Portable.

Frequency : 50 - 400 Hz

Electronic energy meter, power transducer, precision power meter and other power and energy monitoring devices, Over current protection circuit of motor and other electrical appliances.

Models : PG08T Features : Three Pin Socket & Plug Suitable for Indian Socket Large LCD Display with Backlight Memory Retention (KWh, MIN, CU, CU/KWh, CO2) Counts CO2 generated by Electrical Equipment (0.555kg CO2 is generated by using 1 KWh Energy) Timer & Relay Function for Power ON / OFF the Load TRMS V & mA for Sine Wave   Measures Power (W) Power Factor (PF) Carbon Emission (CO2 in Kg) Total Used Time (MIN) Money (CU) Tariff (CU/KWh) Timer (DHH:MM) Frequency (Hz) Energy (KWh) TRMS Current (mA) TRMS Voltage (V)   Applications Teaching, Demonstration & Testing of Electrical Energy Consumption of Household / Office Appliances like Refrigerator, Washing Machine, Microwave Oven, LED Lights etc. It can be used in Houses, Offices, Shops, Schools, Laboratories etc. Ordering Information Model

Clamp-on power meter harmonics analyser.   Clamp-On TRMS Power Meter Harmonics Analyser, Harmonic Tester, Energy Auditor

In Electrical System, sometime without identification of Phase Sequence it is impossible to proceed further. The Phase Sequence Indicator is used to determine the Phase Sequence R, Y & B of 3 Phase Voltage. It is important that Phase Sequence is known properly prior to energizing electrical motor & other equipment, as incorrect connection could cause damage to the equipment. The correct operation of measuring instrument like 3 Phase Energy Meter, 3 Phase Power Meter and Automatic Control of devices also depend on the Phase Sequence.

Model, Input Voltage, Input Current, Input Frequency, CTR PTR (if any), Auxiliary Supply, Accuracy Class and Display Digit Height

Digital panel meters and modules power line transducers analog panel and switchboard meters multifunction meters.

TRMS Measurement 23 Parameters on 46 Pages 4 Rows of 4 Digit Super Bright RED LED Display 3 Phase 3 Wire 3 Phase 4 Wire System (User Selectable) Programmable CTR, PTR, Instrument Address, Password and MD Period Energy Import - Export (4 Quadrant Operation) IP54 (For Meter Front) POWER MASTER Software (Optional) RS485 Port, 5KV Isolated with MODBUS RTU Protocol (Optional) CE Compliance with EN61010- 1, EN61326- 1 Inbuilt Memory to Store CTR, PTR, Instrument Address, Password and MD period Auto Scroll (5 sec.) Manual Scroll Display Built in 20 Energy Meters of 8 Digit Resolution Energy Retention and Password Protected Energy Reset Facility Max. Demand for KW or KVA with user Selectable Demand Interval 5-30 Minutes THD for Voltage and Current Password for Protection of Programmable Parameters RUN Hours, ON Hours Phase Angle and Phasor Angle Measurement Display Previous Energies Set Date and Time Measurement of Min. and Max. Voltage and Current Values.

9V Eveready Type 216 or Equivalent & External Battery Pack (6 x 1.5 V AA Batteries), 4 and 5 Digits with Annunciator, Operating Environment :- 0 ºC to 50 ºC (32 to 122 ºF), RH < 85%.

Weight : 330 gms

Moving Iron Meter of 90° Deflection with Interchangeable Scale Facility, Moving Iron Spring Mounted Jewel Bearing Suspension, Model, Input Range, CTR PTR, Scale

Moving Coil Meter of 90° or 240° Deflection with Fixed Interchangeable Scale Facility, Moving Coil with Central Magnetic Core, Spring Mounted Jewel Bearing Suspension

Manual or Auto Range, Four Terminal Kelvin Measurement, 6 Ranges with 1mV Best Resolution, Measurement of Resistive and Inductive Materials, Memory of 3000 Measurements Data, LED indication for Invalid Resistance Measurement, Cable Length Measurement in feet & meters

Weight : 1125 gms

Large Conductor Diameter (30mm), AC Current in 5 Ranges (40mA, 400mA, 4A, 40A, 60A), Wide Frequency Response (40Hz-1KHz), ACA, ACV, Ω and Continuity, Large 3¾ Digit LCD (4000 Count), 40 Segment Fast Bargraph Display (20 timessec.), Data Hold and Max Min Hold, Relative Measurement

TRMS Using Micro-Controller 4 Digit 9999 (Max.) Counts, High Resolution Display User Programmable Display (Primary CT Shunt Value) Auto Selection of Decimal Point Red LED Super Bright Display High Accuracy Across the Entire Range Auxiliary Supply : 230V AC ± 20% @ 50 60 Hz.