Air Dryers Dealers in Sector 63, Noida

Compressed air with saturated water vapor enters the dryer’s pre-cooling device, in which, the entered hot air is cooled down by the outgoing cold air partly, thus reducing the load on the system (this process is pre-cooling). Pre-cooled air enters the evaporator. Here, heat released by the air is absorbed by media and the air reaches the pre-set temperature (2 ~ 4oC). After being cooled, the water vapor in the air condenses into droplets and is separated from the air by steam separator and then flows out of the dryer through automatic drainer. Leaving the separator, cold air enters into the pre-cooling device’s shell side for heat exchange with hot air in the inlet and leaves the dryer after being heated to a temperature about 10oC lower than that of the inlet air. This reheating prevents the second moisture condensation in the outside exit air pipeline and downstream pipeline, increases the energy of the air and improves the effectiveness. In addition, after passing through the dryer, solid dust of over 3μ in the compressed air is all filtered, and the air source quality reaches the clean and dry requirements.   Salient Features Economical in power consumption in comparison with other type of dryers for equivalent dew point. Innovative Heat Exchanger ensure max. Heat transfer & low pressure drop. In built safety devices for compressor, condenser etc. Consistent Dew point over wide range of flows. Simple design, easy access to all parts requiring almost no maintenance. Modular skid mounted unit in robust industrial cabinet is prewired and piped. Inbuilt air, electrical & drain connection. The dryer is ready to start saving your money. High quality product due to stage wise inspection & testing before dispatch.

Adsorption dryers (Heatless) are designed with the consistent efforts of our professional team and the vast knowledge that they owe. These dryers’ works on a twin-tower alternative operation mode when the compressed air enters the dryer’s tower A through valve 1A. The air is then dehydrated and dried under the adsorption action of the adsorption use.

• USES: Telecom industry, Pneumatic control systems, Textile industries, Pneumatic tools, Paint industry.
• Features: Economical functioning, low power consumption, Innovative heat exchanger design .

In this dryer, compressed air is passed though the regenerated desiccant bed for moisture removal and dry air comes out from the outlet. For regeneration of desiccant, atmospheric air is heated to a temp of 175Deg C & passed through the saturated desiccant bed in counter direction. All the adsorbed moisture vaporizes and is vented out. Cooling of the bed may be done with atmospheric air but without heater or some air may be re-circulated through heat exchanger, depending on the dryness of air required. This is a no purge loss type system which can dry air upto(-) 80 Deg.c. Generally such dryers are preferred for higher flow rates.   Salient Features : Low operating cost for high capacities. Dew point upto (-) 60 Deg C can be achieved. Most economical in the range from 1000 CFM onwards

Under the process division, we are supplying various types of industrial compressors such as reciprocating, centrifugal, sliding vane designs for air & gases application. Apart from being the sales representative for the principal companies that we represent, with network coverage in all metros, we have a well established team for service & spares that enable us give the client local support sought. We are also supplying industrial blowers & fans to meet all the requirements of various process industries. We are also able to take up jobs for Air separation plants, i.e. oxygen plants, Nitrogen plants etc. Working on cryogenic technology, PSA or VPSA methods. Our principal company is one of the major suppliers of Air separation plants in the world and have done a few jobs in India as well. We ensure desired purity at optimum project cost. Other products include AIR & GAS DRYRES & Accessories and AUTOMATIC SELF CLEANING FLUID STRAINERS, which are used for critical applications where the flow of the fluid cannot be stopped for cleaning of the filter element.

• Material: Stainless steel
• Automation Grade: Automatic
• Voltage: 230 V
• Phase: Single
• Brand Name: PRECIMOULD
• Capacity: 25kg 50kg 75kg 100kg
• Design: Standard

Chilling Plants, Cooling Tower, Haridwar

adsorption dryer, water cooled scroll chiller, Air Cooled Liquid Chiller