Air Dryers Dealers in Sector 64, Noida

In this dryer, compressed air is passed though the regenerated desiccant bed for moisture removal and dry air comes out from the outlet. For regeneration of desiccant, atmospheric air is heated to a temp of 175Deg C & passed through the saturated desiccant bed in counter direction. All the adsorbed moisture vaporizes and is vented out. Cooling of the bed may be done with atmospheric air but without heater or some air may be re-circulated through heat exchanger, depending on the dryness of air required. This is a no purge loss type system which can dry air upto(-) 80 Deg.c. Generally such dryers are preferred for higher flow rates.   Salient Features : Low operating cost for high capacities. Dew point upto (-) 60 Deg C can be achieved. Most economical in the range from 1000 CFM onwards

• Material: Stainless steel
• Automation Grade: Automatic
• Voltage: 230 V
• Phase: Single
• Brand Name: PRECIMOULD
• Capacity: 25kg 50kg 75kg 100kg
• Design: Standard

• Inlet/Outlet connections: ½" BSP

Compressed air dryer are removed in water separator. The resultant compressed air becomes dry to pressure dew point equal to its reduced temperature (generally around+2°C to +8°C). As long as the temperature of compressed air, as it travels through the system does not fall below the dew point temperature produced in the dryer, no more water vapours will condense into troublesome liquid in downstream air lines.

• Features: Cost effective, Compact design, Low maintenance, Easy to install, Less power consumption, Increased desiccant life, In-built safety measures.
• USES: In cool towers

Compressed air with saturated water vapor enters the dryer’s pre-cooling device, in which, the entered hot air is cooled down by the outgoing cold air partly, thus reducing the load on the system (this process is pre-cooling). Pre-cooled air enters the evaporator. Here, heat released by the air is absorbed by media and the air reaches the pre-set temperature (2 ~ 4℃). After being cooled, the water vapor in the air condenses into droplets and is separated from the air by steam separator and then flows out of the dryer through automatic drainer. Leaving the separator, cold air enters into the pre-cooling device’s shell side for heat exchange with hot air in the inlet and leaves the dryer after being heated to a temperature about 10 ℃ lower than that of the inlet air. This reheating prevents the second moisture condensation in the outside exit air pipeline and downstream pipeline, increases the energy of the air and improves the effectiveness. In addition, after passing through the dryer, solid dust of over 3μ in the compressed air is all filtered, and the air source quality reaches the clean and dry requirements.    

We are offering refrigerated air dryer. The basic principle is the removal of moisture by cooling air to certain present temperature. The concept of efficient cooling is removal of heat only. The air first enters into the precooler where the incoming hot air is being cooled by outgoing cold air so as to reduce the heat load of evaporator . The air from precooler enter into the evaporator where further heat is removed by boiling refrigerant like freon. Now the air get condensed and this moist air is passed through a moisture separator where moisture is drained out by centrifugal action of air. The moist free air enters into precooler to cool the incoming air. Salient features: simple and compact design. Automatic cleaning of condenser. Efficient power saving. Least pressure drop. Easy maintenance. Specification: range : 5 to 1000 nm3/hr pressure : 0. 5 to 12. 5 barg. Electrical connection: 415v , 3phase , 50 hz refrigerant: r22 dew point : (-)23.

Having the support of an expert team, we have successfully developed Refrigerated Air Dryers. These dryers worked on the principle of compressed air with saturated water vapor that enters the dryer's pre-cooling device. This air is cooled down with outgoing cold air, thus reducing the load of the system.

Under the process division, we are supplying various types of industrial compressors such as reciprocating, centrifugal, sliding vane designs for air & gases application. Apart from being the sales representative for the principal companies that we represent, with network coverage in all metros, we have a well established team for service & spares that enable us give the client local support sought. We are also supplying industrial blowers & fans to meet all the requirements of various process industries. We are also able to take up jobs for Air separation plants, i.e. oxygen plants, Nitrogen plants etc. Working on cryogenic technology, PSA or VPSA methods. Our principal company is one of the major suppliers of Air separation plants in the world and have done a few jobs in India as well. We ensure desired purity at optimum project cost. Other products include AIR & GAS DRYRES & Accessories and AUTOMATIC SELF CLEANING FLUID STRAINERS, which are used for critical applications where the flow of the fluid cannot be stopped for cleaning of the filter element.

Chilling Plants, Cooling Tower, Haridwar

Refrigerated Air Dryer, water cooled scroll chiller, Air Receiver

Refrigerator Air Dryer, oil free compressor, Sullair Air Compressors

psa nitrogen plants, low pressure dryers, gas dryers, co2 gas dryers