DM Water Plant Dealers in Sector 10, Noida

We are Noida based Manufacturer and Supplier of Water Demineralization Plants, which comprise Two Bed DM Plants and Mixed Bed DM Plants. Our Water Demineralization Plant comes with Weak Base & Strong Base Cation & Anion Exchanger. The Cation & Anion Exchanger, which we offer, is available with Degasification System to physically eradicate alkalinity without the use of chemicals (Saves NaOH), and also helps in diminishing the load on Anion Unit. These Water Demineralization Plants have standard FRP/ Mild Steel rubber lining and SS 316L (Quarts Lined) construction. The Water Demineralization Plant, which we offer, uses an advanced Demineralization or Deionisation process, which is based on caustic regenerated anion resin and acid regenerated action resin to remove the minerals from water. We make available Water Demineralization Plants in diverse sizes depending on the needs of the clients. The design of our Water Demineralization Plant endeavors to save cost and conserve water. These Water Demineralization Plants are available as manually operated or fully automatic deepending upon the needs of the clients. Highlights Using the ion exchange process, it removes mineral salts from water In the Two Bed Water Demineralization Plant, Strong Base Anion Exchanger and a Powerful Acid Cation Exchanger are put to use for reducing the total dissolved solids up to 2-5 ppm. We provide an outlet- conductivity meter, to check the quality of the treated water.Mixed Bed Units are used in series with Two Bed DM Plant as a polisher unit which can produce treated water having conductivity < 1 mS/cm.We offer the Cation Polisher Unit used for achieving Acidic Water Quality for Specific applications.DM Plant produces treated water, which has a conductivity less than 10 mS/cm (for Two Bed) and less than 1 mS/cm with pH as desired.The Water Demineralization Plant has a capacity of 100 to 2, 00,000 liters per day, which depends on water property and the requirement for water. Availability The Water Demineralization Plant is available in diverse sizes having cation and anion exchanger unit with 200 mm to 2000 mm diameter, which comes in either Valves or Multi Port Valve depending upon the sizes desired by the clients. A trolley mounted automatically operated Water Demineralization Plants are also available for small industries and laboratories. Operating Principle A Typical two-bed DM Plant consists of two FRP/MS rubber lined pressure vessels connected in series along with its internal fittings. The first unit consists of high capacity strongly acidic cation exchange resin, which converts positive ions of salt and replaces them with hydrogen ions to form respective acids, which are absorbed in next vessel by strongly basic anion exchange resin. The water obtained by this process shows conductivity less than 20 µ S / cm at 25o C and total dissolved solids less than 10 ppm. Further, highly purified water can be achieved by Mixed Bed Deionizers, which are specifically designed for the same purpose. They can be used as polishing units after Two Bed DM Plant to obtain high purity water. Mixed Bed Deionizers are single column units, filled with strongly acidic cation and strongly basic anion exchange resins mixed together. There are four distinct stages in the operation of Deionizers Service : In the service cycle the water enters the vessel and passes through the resin bed of the respective exchanger Backwashing : After the resins are exhausted, the bed is backwashed. Backwashing is carried out by a uniform upward flow of water through the resin bed. The backwash step expands the resin bed releasing any entrapped particulate matter & removes the channeling in the resin column, if occurred during the service cycle.Regeneration : When the ion exchange resins lose all the exchangeable ions, they require regeneration to restore them back to hydrogen or hydroxyl form depending upon whether they are cation or anion resins. To achieve this 4 - 5% concentrated solution of Hydrochloric acid is used for cation resin and a 4% - 5% concentrated solution of caustic soda is used for anion resin. Sulphuric acid can also be used for Cation Regeneration but the concentration of acid during injection must be kept at minimum, such as to prevent calcium sulphate precipitation on the resin.Rinse/remix

DM Plant in various sizes ranging from 500 ltrshr up to 100 m3hr and above. These are manufactures using FRP pressure vessel, internal distribution and collection system, multiport or individual valves, piping, century for acid or alkali injection, solution tanks, for acid and caustic, test kit, conductivity meters etc.These units are available with multiport or individual valves.We offer poly styrene di-vinyl benzene (resin) of either ion exchange make or lanxess make for better water quality. Backed by rich industrial experience, we manufacture and export a superb quality range of Mixed Bed DM Plants Auto SS, which require supply of water, drain as well as electrical. These products are used in various industrial applications and are manufactured using FRP pressure vessels, collection system, individual valves and many other products and we offer these in different specifications as well as dimensions to our clients. Our plant have various special feature from others like Pre assembled, Factory tested systems, Compact, Easy to maintain, Electrical controls etc. Water having carbonic acid are passed through the Degasser Towers which contains pall rings to give little obstruction to the water flowing down, Air blown in upward flow removes the carbon dia-oxide from water leaving purified water. This water is collected in either in HDPE Tank or Mild Steel Tank or RCC Tank depending on Volume.

demineralization water plant, Sewage Water Treatment Plant, Bottling Plant