KVA Power Equipments LLP Sector 8, Noida, Uttar Pradesh

We are offering terminal connectors are suitable for the conjunction of wires, cables in the power distribution equipments. These connectors are type tested by various accrediting govt agencies (nabl labs). Each of the product passes through the highest standards of quality and reliability for long-term uninterrupted usage.

Type : KVA Power - terminal connector

Brand Name : KVA Power Equipments LLP

Application : Conjunction of wires, cables in the power distribution equipment

Country of Origin : Noida

Tee Connector is an electrical connector that connects three cables together. It is usually in the shape of a capital T. It is usually used for coax cables and the three connector points can be either female or male gender, and could be different or the same standard.

A connector design for the purpose of connecting together two or more conductors with no allowance for the relative movement between conductors. It is usually used in RF applications.

We manufacture highly efficient and accurate resin cast potential transformers. These resin cast potential transformers are used in ac circuits, for the purpose of measuring large voltages. Their main function is to reduce the supply voltage to a small value so that it can be easily measured with standard low range ac instruments of moderate size and capacity. There are many advantages of using resin cast potential transformers for range extension of ac meters. We also offer resin cast potential transformers of dual purpose metering & protection that are also commonly used. Thus, the resin cast potential transformers are basically dry type transformers, whose active part is completely embedded in quartz loaded epoxy resin by using vacuum molding technique

Brand Name : KVA Power Equipments LLP

Phase : Power Transmission Equipments

Country of Origin : India

Usage : Metering/ Protection

Epoxy Resin Cast Current Transformer (CT) Resin cast current transformers are available for metering and protection application. These current Transformers are mainly fabricated according to clientÃ�¢Ã¯Â¿Ã‚½ÃƒÃ‚¯Ã‚¿Ã‚½s specification. CT coils are encapsulated in cast resin (Polyester Epoxy). Secondary terminals are provided with either screws or studs. Terminal cover & CT mounting clamps are made available on request. Resin Cast Transformers are dry type transformers the active part of which is completely embedded in quartz loaded Epoxy Resin by using vacuum molding technique. After molding the resin is hardened by polymerization. The main insulation between Primary and Secondary and Earth is obtained by this epoxy resin. These transformers are of compact design with high mechanical and electrical properties. These are non-hygroscopic and hence give very good insulation properties even in given humid conditions.

Brand Name : KVA Power Equipments LLP

Phase : Power Transmission Equipments

Country of Origin : Noida

Usage : Metering/ Protection

We are the manufacturer of resin cast current transformers, are available for metering & protection application. Ct coils are encapsulated in cast resin (polyester epoxy). Resin cast transformers are dry type transformers the active part of which is completely embedded in quartz loaded epoxy resin by using vacuum moulding technique.

Brand Name : KVA Power Equipments LLP

Phase : Power Transmission Equipments

Country of Origin : Noida

Usage : Metering/ Protection

We are the leading manufaturer and supplier of PT Coils. Features: Accurate in shape Compact Size Moisture Proof.

A connector design for the purpose of connecting together two or more conductors whose axes is parallel to each other. The connector body is constructed of high strength aluminum for optimum corrosion resistance and light weight. The housing or case provides protective insulation from adjacent conductors and is formed for accessibility and ease of application. Secondary run and service tap openings are pre-cut for alignment and tap conductor insertion or removal.

Industrial metering cubicles are used for the controlling of the incoming power supply voltage and its distribution among the other appliances in the industry in most appropriate and desirable manner. These are provided with auto sensing and intelligence technologies to make its work more efficient and reliable. The cubical are dust proof and pilfer resistant. The cubical are available in three phase three wire or three phase four wire systems. It is widely acclaimed in the industry, owing to its ease of operation, minimal maintenance and low cost. Features: � Used for Indoor/Outdoor Installations and completely sealable in order to prevent power theft. � Mainly used for AMR Systems. � Dry type resin cast CTs and PTs are used. � this being a compact unit is easy to handle. � Less in weight in weight and volume as compared to 5/6 single phase units. Technical Specifications: General Particulars In KV Nominal System Voltage 11 Highest System Voltage 12 Insulation level 12 Standard Impulse with stand voltage 75 HV Power freq. withstand volt. for Primary Winding 1 Min 28 HV Power freq. withstand volt. for Secondary Winding 1 Min 3 PD measuring voltage 7.6 Rated Frequency (Hz) 50(Hz) Current Transformer Potential Transformer Rated Burden 2.5 to 25 VA Rated Burden 10 to 100 VA Rated Primary Current (Amp) 2.5 Amp to 800 Amp Rated Primary Voltage 11KV Rated Secondary Current (Amp) 1Amp to 5 Amp Rated Secondary Voltage 110 volt Rated Short Time Thermal Current 3KA to 25KA for 1/3 second Rated Voltage factor 1.2 cont. & 1.5 for 30 second

Type : Outdoor

We offer low tension current transformer. It is not possible to use line current directly for measurement and relaying purpose due to its high value and insulation problem. Current transformer which is widely known as 'ct' is a piece of electrical equipment which converts line current values which are suitable for the devices to which is connected e.g. Measuring instruments, meters, protection relays. basic functions of cts are : to reduce line current to a value which is suitable for measuring instruments, relays etc. To isolate the measuring instruments, meters, relays etc. From line voltage of an installation. To protect measuring instruments against short circuit currents to sense abnormalities in current and give current signals to protective relays to isolate the defective system.

Type : LT. Current transformer

Usage : Metering/ Protection

Phase : Power Transmission Equipments

Brand Name : KVA Power Equipments LLP

Country of Origin : India

A connector design for the purpose of connecting together two or more conductors whose axes is either in line or at an angle to each other.

A Connector designed for the purpose of connecting two or more conductors & incorporating means to allow for any relative movement with ample allowance for the relative movement between the conductors. It is an assembly designed to safely absorb the heat-induced expansion and contraction of construction materials, to absorb vibration, to hold parts together, or to allow movement due to ground settlement or earthquakes.

A connector design for the purpose of connecting the terminals of the equipment to the conductor. It is an electro-mechanical device used to join electrical terminations and create an electrical circuit.

Gender : Female

Country of Origin : India

We are the Leading manufacturer and supplier of CT Coils. Features: Perfect in shape Compact size Moisture Proof.

As a leading manufacturer and supplier in this domain, we are offering a high quality compact substation which has compact and sturdy design to save space. It is pre-fabricated secondary sub station containing, distribution transformer, medium voltage switch gear, low voltage switch board, connections and associated equipments in a compact unit. All components are housed an enclosure, which protects the equipment from environment hazards and unauthorised access. The electrical equipment is cooled by natural ventilation through openings in the sub station. It is designed in accordance with IEC-61330 standards. The Compact Substation is computerised with suitable medium voltage, low voltage sections and transformer section with separate doors for each compartment. Features: • Compact and sturdy design to save space • Flexibility in selecting the required LV and HV equipment • Standard design and construction reduces turnaround time • Properly designed Earthing system

A connector design for connecting of two or more conductor of different materials (normally copper & aluminium conductors) for preventing electrolytic corrosion. The connector comprises a copper portion and an aluminum portion joined in a solid state bond and having an axial wire receiving opening in the aluminum portion and having electrical connection means, such as a threaded hole, in the copper portion. Tooling and indexing bosses and tool engaging recess means are integrally formed on the exterior and interior of the aluminum portion.

Type : Bimetallic Connector

Material : Copper and Aliminium