Sensors Dealers in Sector 11, Noida

• Ambient Temperature: 20*C to +45*C
• Insulation Class:: E (120*C Max.).

VAISHNO CFG" Make low voltage current transformers as per IS standard of IEC 60044-1(BSEN 60044-1). CT's convert an alternating current usually high into a proportional lower one, depending on their use. The design of the Current transformer requires the inclusion of a core and winding which will when connected to its rated burden ."VAISHNO CFG" Make CT's are broadly classified into the three groups as per their requirement as under: Current Transformer: An instrument transformer in which the secondary current, in normal condition is use, subsequently proportional to the primary current and differs in phase it by an angle which is approximately zero for an appropriate directions of correction. Measuring Transformer: A current transformer intended to supply indicating instruments integrated meter, relay and similar apparatus. Protective current transformer: A current transformer intended to supply protective supply.

• Application: Level Sensor
• Condition: New
• Output Method: PNP NO
• Operating Voltage: 12
• Response Frequency: 200HZ
• Detection distance: 26mm

We have adopted modern work methods that aid us completely in maintaining records and give us alerts time-to-time when any products goes short in the shelf. Being a high-flying name in this arena, we promise to deliver the best in line quality products. In addition to this, we make sure that the offered lot is prepared using the finest grade material.

ATEX approved reed sensors are tested to carry out switching functions in potentially explosive atmospheres such that they will not become an ignition point when subjected to short circuits or adjacent component failures. They must also switch to a defined state when subjected to overload conditions. Reed sensor products meeting these requirements are generally referred to as intrinsically safe.Features ATEX approved - Intended for use in potentially explosive atmosphere Hermetically sealed Contacts for Long Life Available in SPST-NO Magnetically Operated Sensor Available in SPST NO Version. Choice of cable length and Termination is possible Magnet is available sealed with housing

The ICIR-730D is an occupancy sensor developed for automatic control of HVAC operations. This sensor is designed for recess mounting with the EIA standard single gang box with 83.5mm screw pitch. An innovative dual delay processor makes this sensor smart enough to verify the nature of occupancies. In addition to the HVAC operation control, this duplex occupancy sensor also provides signal for instant light control. With one installation, the ICIR-730D can offer both HVAC and lighting controls to maximize the benefits of occupancy-oriented building energy management system. Features:   Dual element infrared sensor Form C HVAC control output Instant light control output Adjustable LUX level control Selectable ON and OFF delays Disabled walk test LED Superior RFI/EMI immunity High density detection zones Temperature compensation 140° ultra wide angle detection Specifications: Power supply: 24 ± 2VAC/DC Current drain: Standby: 8mA, Active: 20mA @ 24VDC HVAC control: Form C, 30VAC/DC, 0.2A max. Light control: TTL output, standby: 0V, active: 5V Detectable speed: 0.1~3m/sec. Mounting height: 1.2~1.5m Delay time (ON): 0/10\"/20\"/30\"/1\'/2\'/5\'/10\' selectable Delay time (OFF): 10\"/30\"/1\'/3\'/5\'/10\'/20\'/30\' selectable RFI immunity: Ave. 20V/m (10~1000MHz) Humidity: Max. 95% RH Temperature: -20°C~60°C (-44°F~140°F) Dimensions: 120 x 70 x 50mm

Pressure Sensor - 1 output Digital Pressure Sensor (Series PS - R18 2 Colours display (Red Green) Set pressure selectable (kPa, psi, kgfcm2, bar) Both upper and lower limits of pressure can be set independently Panel mountable Direct mountable Both PNP & NPN versions Single output

• Applied Sensor: Vibrating Wire
• Range: ±5° ±10°
• Resolution: 5arc second /10arc second
• Accuracy: ±0.1%FS
• Non Linearity: ±0.5%FS

Tilt Sensors are used to monitor changes in the tilt of a structure. Such changes may be caused by excavation, tunneling, dewatering, or loading of the structure. Typical applications for tilt sensors include: Monitoring stabilization measures, such as pressure grouting and underpinning. Monitoring structures for the effects of tunneling and excavating. Monitoring the deflection and deformation of retaining walls. Monitoring convergence and other movements in tunnels. Providing early warning of threatening deformations, allowing time for corrective action to be taken.

temperature probes, Thermocouple Tips, immersion samplers

• Application: Industrial
• Color: Black

• Type: Photoelectric Sensor
• Application: Object Detection
• Material: Plastic
• Color: Black
• Model Number: Photoelectric Sensor
• Brand Name: Omron
• Country of Origin: Made in India

wireless motion detector, Access Control System, attendance recorder

motion detector, biometric access machine, Video Door Phones, spike barriers

vibration monitoring system, 3d white light scanner

security sensors, access control, Public Address System

Monitor Sensors, Computer Printers, computer systems, Laptop Accessories

Sensors, Chopper Controller, Motion Control Card, Servo Motors

Melt Pressure Transducers, Injection Molding Machine Repair Services

Knock Sensor, Auto Suspension System, Axle Shaft, fork legs, Gaskets

Steering Angle Sensor, Gear Shift Lever, Poka Yoke System

Horizontal Float Sensor, Magnetic float sensor

motion detectors, Biometric Access Control Systems, Cameras