Wheels Fabricators Pvt Ltd Industrial Area Phase I, Panchkula, Haryana

Wedge

Verticals are Available to Suit Any Propping or Access Application Economically. the Connection Point is Set At 500 / 1000 Mm Vertical Intervals for Maximum Venatility in Use. the Lower Cups are Welded in Position, the Upper Moveable Cups are Retained By a Fixed Stop. the Verticals are Drilled for the Fixing of Spigot Joint. a Bolt Can Be Used to Restrain Upward Forces if Required. These are Available in Different Sizes 3000 Mm, 2500 Mm, 2000 Mm, 1500 Mm, 1000 Mm or as Required.

V-Pressings

Universal Jack

U-Clip

Top Cup

Manufactured out of sheet, Lattices of 10mm dia bar, main bar 14 mm dia, bearing angle 75x75x10 mm, one no. of eye bolt with additional angle stiffener welded to the sheet and bearing angle from inside.

Tee Bolts

We are Offering T-bolt.

Swivel Coupler Body

When Necessary Verticals are Connected End to End By An Internal Spigot (square , Round). this Bolted to the Lower Verticle.

Spare Forged Cap

Sleeve Coupler designed with wrapping facility for end to end connection of any Scaffold tube to form a butt joint connection. Suitable for joints where tension will be developed in the tubes.For Pipe OD 48.3 mm (EN 74 / BS 1139)

Tubes and Fittings Scaffolding are Widely Used for Supporting Man and Materials, Tools and Tackles During Construction, Alteration, Demolition and Maintenance Works Because of Their Several Advantages Over Conventional Type of Timber /bamboo Scaffolding.features : Ease and Speed in Erection and Dismantling. Scopes for Multiple and Varied Re-use (life and Flexibility in Use) Rigidity and Stability During Erection. Ease in Storing and Maintenance Reliable Assessment of Performance with Adequate Scopes for Safety. Eco-friendly.

Props provide the ideal and the most economic method of support for all kinds of formwork, slabs, beams, wall & columns. They are also invaluable for a wide variety of applications in general building construction and repair work. Props eliminate the costly labour and time consumer in cutting timber to length, wedging and nailing when used in the vertical as a prop.Unique Features : The high tensile steel pin is located through a slot in the outer section and a hole on the inner section for coarse adjustment.The cast collar located below the pin gives fine adjustment for lending and striking.A self-cleaning device on the collar nut, which automatically clears the thread of concrete, and dirt where the nut is rotated thus assuring quick and easy adjustment.A hole boss on the collar nut which makes it easy to turn in confined spaces. By inserting a bar in the hole.Base plates and head plates are holed for use with slab from work.TPI ACME square thread ensure load bearing strength at this critical point Standard special shores pins are also available on request. Beam type or U-head Props are also available according to customer's requirement.

For Pipe OD 48.3 mm (EN 74 / BS 1139)

For Pipe OD 48.3 mm(EN 74 / BS 1139)

Pressed Swivel Coupler is used for connecting 40 mm NB tubes at any angle other tubes, ledgers or props for diagonal bracings. Size: 48.3 X 48.3 mm O.D. 48.30 X 60.30 mm O.D.

Pressed Double Coupler is Used for Joining 40 Mm Nb Tubes At 90 Degrees Angle to other Tubes, Ledgers or Props.size :48.3 X 48.3 Mm O.d.48.30 X 60.30 Mm O.d.

Ledger Blade

They are a Rolled "t" Section with Wedge Fixing Device On Each Ends. also Available with Back to Back Angles of 50 X 50 X 5 Mm to Form a "t" These Transoms Engaged with "v" Pressing.

A length of 38 mm X 38 mm angle iron with a dowl at both ends. Used to connect stage brackets together.