Reverse Osmosis Plant Equipment Dealers in Patna

• Brand Name: Power Guard
• Material: SS
• Rated Frequency: 50 Hz.

Our company offers convenient payment choices. We are well versed with diverse payment methods. Whether online or offline, patrons can make payments as per their convenience. Since, our entire range is produced by following rules set by global quality regulation standards it is of supreme grade.

• Type: Dialysis Ro Plant
• Application: Water Purifies

A reverse osmosis plant is a manufacturing plant where the process of reverse osmosis takes place. An average modern reverse osmosis plant needs six kilowatt-hours of electricity to desalinate one cubic metre of water. The process also results in an amount of salty briny waste.

We are offering commercial ro water purifier. 1500 lph ro plant in bihar use jar filling

Membrane Housing (4.0"E) that we export and supply is designed for continuous and long term use as housings for membrane filtration. Our Membrane Housing is used to treat tap, brackish & sea waters. Our Membrane Housing can accommodate any standard 4 Inch nominal diameter & 40 Inch long spiral wound membrane with ease. In case of female membranes only, membrane interface adapters will be required, which will be supplied along with the housing.   User's Guide : Guidelines & Information incorporated in this User’s Guide are intended only as a supplement to good industrial practices. The guide should be used in combination with Engineering Drawing of respective membrane housing model used.Material Receipt : On receipt, ensure that all the material is received as per ordered qty & in good condition. For any shortages in receipt, intimate the supplier within the stipulated time to void the warranty & in case of transit damages, intimate the concerned insurance agency.Handling : Membrane housing shell is made of fiber glass & any impact, scratches or mishandling during unloading / loading will reduce the life or make the membrane housing unfit for usage. Ensure that membrane housing packing is intact till the installation.Installation : Ensure that the installation engineer reads the user guide in detail, before installation. In case of any difficulty, contact the nearest Aquanomics representative.Good industry practices & plumbing / piping codes have to be followed during installation, operation & maintenance in order to assure safe, optimum & long service life of membrane housing. Improper installation can result to catastrophic failure & may result in severe bodily harm or property damage.Quick Checks : Polyurethane or rubber saddles should be used as an interface between the membrane housing shell & skids / frame.Under pressure, membrane housing must be free to expand. Ensure that flexible fittings & couplings are used to allow expansion. Vessel must not be subjected to excessive stress caused by bending moments. Vessel ports & components should not be used to support piping manifolds or any other components.Aquanomics 4 Inch Membrane Housing – User’s Guide : Water Leaks Any water leaks from vessel / piping during installation / commissioning should be arrested immediately in order to keep the end plugs & retaining rings clean, dry & free from corrosion. Failure to do so can lead to catastrophic failure & may result in severe bodily harm or property damage.Special Requirement : Aquanomics provides engineering assistance in selecting appropriate membrane housing & specialty steel for specific applications. Get in touch with your nearest Aquanomics representative. However, the final determination including the evaluation of the construction materials for use in specific environment will be the responsibility of the purchaser. Precautions : For safer & better service life of membrane housing, follow all the precautionary instructions given below. Failure to do so will void the warranty.   Mounting :- Mount the membrane housing centered on horizontal members spaced at recommended span (s) using compliant mounting hardware furnished.   Tighten the straps – Maximum one ft-lb.   Piping :- Use flexible piping / victaulic couplings for permeate & feed / concentrate connections. Hanging piping manifolds or supporting other components with the membrane housing may result in damaging of membrane housing. Permeate port is made of Engineering Plastic & Tightening the permeate port more than one turn past hand tight will damage the port.   Overpressure Protection :- Provide overpressure protection for membrane housing set at not more than 105% design operating pressure.   Inspection :- Inspect end closures regularly, replace deteriorated components and correct causes of deterioration.   Servicing :- Relieve system pressure before working on the membrane housing. Working on system under pressure may result in severe bodily harm or property damage.   Before Start – Up :- Ensure that the retaining ring is in place and fully seated in the groove.   Pressures :- Operating the vessel in excess of the ratings, will shorten the life & may result in severe bodily harm or property damage. Engineering permeate port are designed to operate at 125psi,operating at pressure in excess of 125psi must be approved by factory.   Aquanomics 4 Inch Membrane Housing – User’s GuideMembrane Housings are not designed for Vacuum conditions; operate only in positive pressure applications.   pH Operation :- Membrane Housings are designed for continuous operation at a pH of 3 – 11 & for intermittent cleaning pH 2 –12 for less than 30 minutes.   Stoppage :- Some feed waters may cause corrosion under static condition, in order to prevent the system from corrosion, it is recommended to flush the system with permeate water.   Engineering : Ensure that the operator / Engineer who carries out the servicing / maintenance schedule has good knowledge of plumbing, hydraulics, membranes, water treatment & good industry practices.   Removing the End Plug : Relieve the membrane housing of system pressure. Disconnect the feed / concentrate & permeate piping. Mark i dentification on the piping assembly for easy re-assembly. Remove all contaminants & foreign matter from end margin of the membrane housing,using a scotch-brite, sand paper or brush. Any contaminants interfering with the end plug removal will damage the end plug or I.D of membrane housing. Remove the retaining ring out of the shell / insert ring groove. Continue removing the ring by running your finger behind the ring & carefully pulling the ring from the groove.Take care not to get the finger injured. In case if it is difficult to remove the retaining ring due to prolong use, in such case lightly tap the end plug using a plastic mallet or use any releasing spray for quick & easy removal. Connect threaded Engineering Plastic nipple to the permeate port and gently rock the end plug up & down to release the end plug from the shell. Repeat the above steps to remove the end plug from opposite side. If the end plug is with adapter design, remove the adapter by slowly pulling on the adapter body.   Aquanomics  4 Inch Membrane Housing – User’s Guide Closing the End Plug : Check the bore of the membrane housing for any foreign matter or imperfections. Remove all the foreign matter using mild soap solution and rinse with clean water. For imperfections, using a 600 grit sand paper lightly sand the surface & clean with soap water & rinse with clean water. Lubricate all the seals (pwt/ adapter / head) using silicone based lubricant or commercially available glycerin. Apply a very thin layer of lubricant on the seal area of the membrane housing I.D for ease in closing the end plug.Note : Check with your membrane supplier before using the lubricants as they can foul the membranes. If the end plug is with adapter design, insert the adapter in the end plug by slowly pushing in the permeate port tube. Holding the end plug square to the axis of the shell, slowly push the end plug into the shell until the retaining ring groove is clearly visible. Place the end of the retaining ring in the groove of the shell / insert ring & continue pushing the ring counter-clockwise till the ring completely seats into the groove. Reconnect the feed / concentrate & permeate piping. Double check the assembling of end plugs, retaining ring seating in the groove, piping connections etc before pressurizing the system. Take all the necessary safety precautions before start-up. Do not tolerate any leaks. Leaks can lead to corrosion that can lead to component deterioration & eventually catastrophic failure. Membrane Loading / Un–loading :Note : Procedure described below is only for information purpose. Membranes should be loaded / un-loaded according to the membrane manufacturer’s instructions. If membranes are not installed properly, malfunctioning of system /membrane damage may occur. As described in End Plug removal section, remove the End Plugs. For unloading the membranes, push the membranes out of the vessel from the upstream end (feed end). Note: Membranes are always removed & installed in the direction of feed flow. While loading the membrane, ensure that the membrane housing bore & membrane outer surface is perfectly clean & contamination free. Lubricate the seals as per manufacturer’s recommendations. Reinstall the end plug on the down stream end as described in End Plug Closing section. Load the membrane with the brine seal (typically a U-cup seal) installed on the up-stream end with it slip facing up-stream. Push the membrane in the housing until the membrane fully engages with the  head on the down stream end. Once membrane is loaded, close the end plug on the up-stream end.   Inspection & Overhaul :Once the end plug is removed, dismantle the end plug & separate all the components. Clean all the components with soap water, scotch brite & rinse with clean water. Inspect all the components & shell for any corrosion,dents, cracking, softening, discoloring, imperfection, scratches etc.   Plastic (Engineering Thermoplastic) Components :- Cracks & Chip-Off – Replace the components. Softening & Dis-Coloring – Can be due to chemical attack, replace the components,if problem continuous check for alternate material. Damaged Threads – Replace the components.   Metal Components :- Dents & Sharp Edges – Using sand paper polish the damaged area,if the problem can be rectified use it or else replace the components. Corrosion – Can be due to non compatibility of water & metal composition or due to chemical attack. Replace the components & if the corrosion continuous check with factory for alternate material.   Shell :- Check the bore of the membrane housing for any foreign matter or imperfections.Remove all the foreign matter using mild soap solution and rinse with clean water. For imperfections, using a 600 grit sand paper lightly sand the surface & clean with soap water & rinse with clean water. Note :- If any component cannot be restored to working /as new condition, replace the parts. Use of damaged components can lead to catastrophic failure. Every time the vessel is serviced, replace used seals with new ones.

• Application: Reverse Osmosis

Offering 500 LPH RO plant in 1054 vessel with starting price of Rs. 75000/-*

• Country of Origin: India
• Application: Industrial RO Plant
• Max Water Recovery Rate: 55-60 %
• Material of Construction: FRP
• Automation Grade: Automatic
• RO Capacity (Liter/hour): 1000 LPH
• Chiller Cooling Capacity (tons): 1 Ton

We have carved a niche in manufacturing and supplying excellent quality RO Membrane Housings. Made under the strict supervision of our expert team members, RO Membrane Housings are widely appreciated for low maintenance. Tested on all quality parameters, Fiberglass (FRP) Pressure Vessel Membrane Housings are known for their high performance. You can purchase optimum RO Membrane Housings from us at reasonable prices. We are capable of delivering all orders on time.Available in : Pressure ratings up to 1200 PSI Ideal for : A variety of applications including Brackish Water, Seawater, Municipal Water Treatment, Industrial Processing, Electronics Manufacturing, Ultra - Pure Water, Food & Beverage, Automotive Application, Power Generation and Health Care.

We make use of the finest grade raw material that reflects in the finished products. Also, we make sure that it is procured from the trusted places only. Supplying wide array of products, we successfully make deliveries within the dedicated time span.Features : Compact construction Suitable design and fitting Low noise Low temperature growth Technical Specifications : Type - Electronic Timing Control System - Microcontroller Ozone Output - 500 mg/hr Timing - In 5 minutes steps Water Quantity - Maximum 10 lit Food Items Quantity - Maximum 5 kg Power - 15w Dimensions (mm) - 320*120*240 New Weight - 0.80 kg Application : Disinfection of Drinking & Cooking water Washing of face, brushing teeth, skin care Sterilization of vegetables, fruits, fishes & meat Detoxification & Pesticide disintegration in vegetables Washing & cleaning of injuries, wounds and sensitive skin

We are especially grateful for demonstrating your distinct fascination in our water treatment scope of item and are particularly appreciative for outfitting us an open door. This will be a little however huge stride in setting up the dependable and commonly gainful connection between and you're Good Self. DS Enterprises Water arrangements were set up in 2015. DS Enterprises is proficient producer and Importer of Water Treatment Equipments. We are related with USA and Taiwan based water treatment organizations for acquisition of segments and outline of Reverse Osmosis Systems. We can configuration, Manufacture and introduce altered frameworks to meet our customer's prerequisites. We keep up a best in class advances and hardware to help our specialists in determination and planning of the best Water Treatment System for the kind of crude water accessible to every individual customer. With clients needs put premier, our adaptable administration style guarantees that we can shape the best relations with customers, stay informed concerning market patterns and supply makers with purchaser input. In the interim, having executed our own in-house quality control framework, we can ensure that all items meet worldwide guidelines. According to your necessity, we are particularly satisfied to present our Techno-business Proposal for Water treatment framework consolidating Reverse Osmosis System, FRP Cap.50 To 5000 LPH for your water application.   Features:   Easy installation Rugged design Long service life

Ro plant 1000 liter

• Type: Reverse Osmosis Plant
• Certification: ISO 9001:2015
• Application: Reverse Osmosis
• Voltage: 220V
• Condition: New
• Power: 3-6kw

Mantratech Ro Plant manufacture and supply superior quality range of Water Treatment Plants for optimum use of scarce fresh water resources. Our range 1000 lph,2000 lph, 3000 lph, 4000 lph, 5000 lph includes Mineral Water Plant, Packaged drinking water plant, Reverse Osmosis Water Plant, Water Softener Plant, Demineraliser Plant, Sewage Treatment Plant. Mantratech Ro System also offer Activated Carbon & Iron Remover Filter, Automatic Water Filling Machine, Ion Exchange Resin (Cation & Anion) & Membranes and more. These treatment plants are manufactured using quality tested spares that ensure durability and low treatment cost.

• Color: White
• Product: Water purifer
• Name: Fedula Zental

Water Purifier RO System

• Type: Water Filter
• Certification: CE Certified
• Weight: 1-2kg
• Color: White
• Voltage: Filter
• Condition: New
• Power: Manufacturer water filter
• Driven Type: Electric
• Working Temperature: Any
• Warranty: 5years
• Mounting Type: Wall Mounting
• Country of Origin: All country
• Brand Name: Sagar,Promise ,Ganga
• Capacity: 10Liter -20Liters
• Installation: Not Available
• Housing Material: Water
• Voltage: Not Available

Water Purifier, Plastic Garbage Bin, Wheeled Garbage Bin, Plastic Dustbins

Commercial Ro Water Purifier, RO Purifier Repair Service

Kent ACE (11032) 7 L RO + UV + UF Water Purifier (White) Boasting features such as the Mineral RO Technology which retains the essential nutrients in water, and the Double Purification process which removes even dissolved impurities like chemicals from water, this Kent Purifier ensures your family's health.

Commercial Reverse Osmosis System, Himalaya Booster Pump

Water Purifier, Induction Cooker, inbuilt oven, gas cook top

domestic ro, Water Jar Cap, PP Spun Filter 10"*2", PP Spun 20"*2.0

Water Purifier

Industrial RO system, RO System, Water Treatment System

Industrial Burners

Domestic Ro Water Purifier, advertising, Commercial Ro Water Purifier

Water Purifier, Water Jet Machines, Mineral Water Purifier, Mineral Water

RO Water Purifier, RO Spare Parts, ro water purifier body, ro booster pump

Reverse Osmosis System, Commercial Reverse Osmosis System

Water Purifier

domestic ro, Commercial Ro System

Water Purifiers