Adhesives Gum Dealers in Kondhwa, Pune

• Purity: 90%
• Storage: Cool & Dry Place
• Water Required: 25-30%
• Colour: White
• Usage: Industrial
• Adhesive Side: Single Sided

TIELO Block Fix is a ready to use, self curing and non-shrink block fixing compound, blended carefully and formulated to a prefect adhesive, based on Portland cement, graded aggregates and polymers. By addition of water a high strength thixo-tropic mortar is obtained which is used for laying of Fly Ash bricks, Aerated light weight concrete, cement & hollow blocks and Cellular concrete blocks. Plaster to a thickness of 12mm can also be achieved with TIELO Block Fix to cover up the block work surface and it meets all Standards Nationally as well as Internationally. It conforms to ANSI A118.1 & ANSI A118.4 (1999) , EN-1348 & ASTM C 1660-09.   USES : For preparation of a thin bed adhesive for fixing of AAC, ALC and cellular concrete blocks both for interior and exterior use.   ADVANTAGES Easy to use, only water to be added & long working time makes work to be carried at a fast pace and is very economical. No curing is required after block fixing work is done. Possess the unique property of getting self cured. High Strength and perfect adhesion between two blocks. Flexible, shock and impact resistant. Good mechanical strength. (Bond strength, compressive & tensile strength) Thinner joints with high adhesion are achieved contributing to the load bearing capacity of the masonry.   APPLICATION All surfaces should be sound, clean and free from any contamination like grease, oil, loose particles etc. and structurally sound. Uneven and rough surface should be made smooth before to application of TIELO Block Fix. It can be applied on damp surface also. All slabs must be plumb and true and should be within 1/4 inch (6mm) tin 10ft (3mm). If any Expansion joints are observed it should not be covered with the mortar and treatment to be done as per technical specification mentioned in the drawing.   Mixing : Mix 20 Kg of TIELO Block Fix with 5.5- 6.0 Litre of potable water. The water should be taken in a container and TIELO Block Fix to be added to the water slowly and mixed with hand or a slow speed paddle mixer for 3-4 minutes to obtain a lump free smooth thixo-tropic mix of trowel able consistency. Water can be reduced or increased slightly to achieve desired consistency.   Application as a thin bed mortar for laying blocks : The substrate over which the blocks are to be laid should properly cleaned from all loose particles before placing the mortar. The mortar is placed on the block work in thin layers of 2mm – 3mm with a trowel and the next layer of blocks are placed over it. The joints between the blocks are maintained as per the requirements and to be filled with the mortar by using a trowel. Plumbing is done to maintain the verticality of the wall.   Smoothing over the block work : Application of a bonding layer of 1mm -2mm thick of TIELO Block Fix is to be done using a trowel and pressing it downwards before placing the mixed mortar. Finally using TIELO Block Fix Adhesive of 8mm-10mm thickness it is smoothened with a wooden/rubber float or sponge.   Cleaning : Cleaning of all tools used to be washed with clean water before it gets dried

We are offering Instant Adhesive.

We are providing dextrin powder that finds extensive application in adhesives, emulsions and firecrackers. Our yellow in color dextrin powders is widely appreciated by the clients for easy solubility in water, low viscosity and binding qualities. Further, following are some other advantages of using our range of yellow dextrin powder: the solution of yellow dextrin is very sticky or tacky and is fast drying yellow dextrin powder is the converted form of the treated starches and is essentially completely soluble in cold water.

• Packaging Type: Plastic Can,Plastic Drums,Packets
• Application: Tile Fixing,Industrials
• Color: Grey,white
• Form: Powder,Liquid
• Types: Ceramic
• Packaging Size: 5-10 kg,10-15 kg,15-20 kg,20-25 kg

TEXYEAR Industrial Adhesives Pvt Ltd is 50:50 JV between leading Taiwan based Hotmelt adhesive manufacturer -Tex Year Industries Inc. & INDUSTRAIL ADHESIVES INDIA to manufacture & market their products in India. TEXYEAR Industrial Adhesives Private Limited has been engaged in the manufacturing and marketing of Hot melt adhesive (Polymelt) for the last 30 years. The Company has set high standards of performance and has fully equipped itself with the required resources to manufacture and sell hot melt adhesive in the national and international markets

• Form: Liquids
• Brand: Loctite
• Condition: New
• Chemical Resistance: Automotive Fluids
• Usage/Application: Rubber to Rubber Boding
• Grade Standard: Industrial Grade
•  :  

We are offering adhesives. best quality adhesives available

Spray Glue 9.5 Litre, Zig Zag Sofa Spring, Sofa Pocket Spring

ADHESIVE, photocopying, Soft Board, White Board, White Board Marker

ADHESIVE, Sealant

Myl Laticrete Tile Adhesives

Astral Adhesive, Tile Adhesive Chemical, Gypsum Products, readymix plaster

ADHESIVE, Ply Boards, Boards, Laminates, Building Materials

Sika Bond Waterproofing Chemical, Conplast WL Waterproofing Chemicals

TILES ADHESIVES, Stone Sealer, floor and wall tiles

Adhesives, Sealants