Condensate Pump Dealers in Pune

Condensate Recovery pump Significant amounts of energy and resources can be saved by setting up a system to quickly recover and reuse Condensate Recovery Pump & Flash Steam. In an indirect heating process only 80% of the steam energy is used for heating & 20% energy comes out in the form of Condensate. We offer the most energy efficient Condensate Recovery pump for recovering this energy.   Reduction in Fuel Bill: Condensate is valuable resource of Heat available in process plant. Recovery of condensate reduces Fuel Consumption significantly by increasing the feed water temperature. Water charges: Any Condensate Recovery Pump not returned needs to be replaced by fresh water, increasing the fresh water requirement of the plant & its chemical treatment cost. Reduction in ETP load: Hot Condensate Recovery Pump drained is taken to the ETP which increases the load on ETP. This can be avoided by complete condensate recovery pump. Maximizing boiler output: As per F & A rating of boiler, hotter the feed water temperature higher will be the steam output from boiler. Reduction in Blow down Loss: Condensate is pure water, which contains almost no total dissolved solids (TDS). Returning more condensate to the feed-tank reduces the need for blow-down & thus reduces the energy lost from the boiler.

• Model Name/Number: P12C
• Voltage: 230V
• Discharge Head(max): 7m(23ft)
• Suction(max): 2 Meter
• Flow Rate(max): 12L /h(3.2GPH)
• Tank Capacity: 45 ml
• Mini Splits Up To: 30,000btu/hr
• Sound Level at 1m: 19dB(A)
• Ambient Temp.: 0-50 Degree C
• Safety Switch: Volt-free alarm, N.C.,230V-2A
• FEATURE: Integral design,Compact, Connect the socket quickly, easy maintenance, Easy installation

• Features: Tested for 1 million cycles , Works on steam/air

he Forbes Marshall Pressure Powered Pump Packaged Unit is designed to pump condensate without electricity, using just 3 kg of steam per ton of condensate. The unit comes along with a condensate recovery meter- to give real time calculations of energy recovered and insulation jackets which further improve the efficiency of the entire system. The compact version eliminates the need for a separate storage tank by placing it within the pump itself. The Pressure powered pump can pump condensate at higher temperatures and pressure.

• capacity: 500 Kg/hr to 30 T/hr.

Uses inexpensive Steam or Air for operation. Energy Consumption is proportional to Qty of condensate returned. No cavitation or impeller to get worn out. Total Y eliminates failures seen in earlier mechanical pumps. Only 1 moving part in HT which makes pump maintenance free. Completely framed structure which makes the pump robust. Stainless Steel internal parts.

Every 6 Deg. C. rise in feed water temperature results in 1% of fuel savings. In order to keep energy requirements minimum, it is important that condensate is handled efficiently and energy from the condensate is recovered.

• Body: Carbon Steel
• Internals: Inconel & Stainless Steel
• Non Return Valve: Stainless Steel Gr. AISI 304
• Steam trap: ASTM A743 Gr.CA40

To overcome stalling situation and to enhance the heat transfer efficiency, it is advised to install Uni Klinger’s Automatic Pumping Trap (UAPT). There are innumerable advantages of installing this device. UKL APT is a device having the combined features of a conventional steam trap as well as a pump. In situation where the pressure of the condensate approaching APT is suitably high, then the delta pressure inside this APT will facilitate this device to perform as a mere conventional trap only. However under stalling conditions where the delta pressure inside APT drops below 0.5 kg/cm2(g), this APT is automatically switched over to pumping mode. During this mode, the motive port opens up to allow motive steam to enter in APT resulting in to immediate pumping of the condensate at elevated place. Advantage of Automatic Pumping Trap – Increase in heat transfer capacity & thus reduction in process cycle time Appropriate & continuous condensate discharge Avoids water hammer Avoids corrosion due to cool condensate in batch production processes Proper temperature control in process Enhanced equipment life Reducing the hunting effect of the temperature control valve Avoids flashing of hot condensate Nil loss of live steam Maximum Operating Conditions Maximum allowable pressure –  14 kg/cm2 Maximum allowable Temperature –  180 Deg C Size – Inlet 25 NB and outlet 25 NB Inlet 40 NB and outlet 25 NB

• Brand Name: Thermax
• Type: Condensate Recovery Pump
• Features: Weather proof with IP 65 protection suitable for outdoor installation, Microprocessor based control with the flow indicator, No moving part pump and hence zero wear and tear.
• Max Flow Rate: 16470 kg/hr
• Model: TACTS
• Usage/Application: Industrial

We are one of the famous company, who are manufacturer of steam powered condensate pump .

Condensate Lifting Pump, Alloy Steel Fabrication Service

Condensate Recovery System Pump, Single Effect Steam Driven Chiller

Condensate Removal Pump, Industrial Steam Boiler, Bulk Storage Tanks