Pump Controllers Dealers in Pune

• Type: Panel.
• Input Supply: 3 Phase 415 V, 50 HZ AC (3 Phase 3 wire)
• Input Current: 0-18 A per phase.
• Output contact Rating: 18 A at 415 volt Contactor. , 7 A at 250 volt.
• Auxiliary Power: No External power is required (Draws power from the Voltage Inputs)
• Working Temp: 0 to 55 ° C
• Storage Temp: 10 to 70 °C
• Relative humidity: 0 95 % non-condensive
• Warm up time: 30 Sec
• Mounting: Surface mounting.
• Enclosure: 275(W) X 185 (H) X 116(D) mm.
• Terminal: Screw ON Terminals.
• UV (RED): Under Voltage Fault.
• OV (RED): Over Voltage Fault.
• SPP/UB/RP (RED): SPP, Voltage Unbalance& Reverse Phase Fault.
• UL/CUB (RED): Under Load & Current Unbalance Fault.
• OL (RED): Over Load Fault.
• Relay (Green): Supply Healthy (No fault)

This controller takes solar power as a input and the power is converted into Varying DC power by solar PV modules depending on changing sun intensities During the day time. Using advance technology ,the varying DC power is converted into A.C power That drives an AC motors or pump set directly. The equipment is micro controller based and operated with software for digital control of all parameters, fault finding diagnostics. Inbuilt Controller with the function MPPT ( Maximum Power Point Tracking).

Manual and Remote start operation Magnetic Pick-up Sensor input for RPM measurements Programmable through front panel with Password protection 3 Analog Inputs, 3 configurable Binary Inputs, 5 Binary Outputs Indication of operational status and fault status Measurement of Battery Voltage, Speed and running hour Engine Protections – Over/Under , Analog protections D+ terminal for monitoring charging alternator voltage Panel Cut-Out : 81mm x 70mm Protection : IP65 at front panel

e are working with a group of professionals who make special emphasis on the products packaging and ensure that the material is procured from the reliable sources only. In order to ensure product compliance with stated quality norms, we conduct several tests at several stages. Details : Power ON LED : It indicates the power supply to the unit. Motor ON LED: It indicates the motor ON and Off Condition Tank Level Indication LED: Two level visual indications – 25% (Low Level), 75% (Tank full level). Motor will automatically switch ON when the water level in the tank is low and automatically switch OFF within 1 second when the tank becomes full. Manual Mode: Helps to switch ON the motor manually. In this mode, the motor will be running till the tank will be full . The product having special features of two relays for submersible Pump. one for starting capacitor and other for running capacitor. The three sensor electrode indicates the water level of the tank. Helps in preventing overflow of water from the overhead tank Input Voltage- 230V to 275 V(AC) Output Contacts-2 NO Long Life Easy to install

The products are strictly packed and dispatched safely to the clients stated address and that too in the committed time span. In order to deliver the best in class finished products, we make use of quality-tested raw material and modern work methods. Also, we make sure that the material is sourced from the reliable places only.

• Driven Type: Solar
• Motor Type: AC
• Motor HP: 0.5 To 10 HP
• Motor: Submersible, Monoblock
• Motor Voltage: 160 V to 380 V
• Motor Current: 2.5 A to 17 A

• Feature: Flameproof, Light Weight
• Voltage: 220V
• Mounting: Wall Mounting
• Warranty: 1year
• Supply Voltage: 95 - 280V AC, 50 Hz.
• Power Consumption: 3VA.

Liquid Level Controller (APC-1) is used to automatically start & stop the pump for filling the tank or emptying the tank with alarm indication With liquid level inputs from the Magnetic Float Switch fitted in the sump and over head tank, (APC-1) controller can be used for PUMP UP or PUMP DOWN operation. Alarm relay is provided to indicate abnormality in the process like liquid level raised beyond high level setting or drops below low level setting in the Overhead or sump tanks.   Inputs : High Level : Magnetic Float Switch Input (Close on Rising Level). High Level : Magnetic Float Switch Input (Close on Rising Level). Low Level : Magnetic Float Switch Input (Close on Falling Level). Low Low Level : Magnetic Float Switch Input (Close on Falling Level). PU/PD Mode Selection : Pump_UP/Pump-Down Mode is selected by Slide Swtich Provided on rear end.   Outputs : Pump Relay No Contact : Potentail free 1No Rated 10Amps @ 250V AC. Pump-UP-Mode : Closes when the liquid level falls below low Low level reaches at or above high level. Pump-Down- Mode : Closes when the liquid level reaches at or above High level and Opens when the liquid level falls below Low level. Alarm Relay NO Contact : Potentail free 1No Rated 10Amps@250V AC. Closing When the Liquid level goes above High High level or Liquid level falls below Low Low Level and Opens when the liquid level Normal conditionor by Alam ACK button provided on front panel.

Catering to the customers needs with excellence, we, as a Supplier engaged in offering a qualitative array of Electric Solar Water Pump Controller. We are a focused towards bringing forth exceptional array of products that are quality tested from the initial stages of manufacturing. Our quality inspectors inspect each and every element of the raw material with complete proficiency

Solar pump offers a clean and simple alternative to conventional electrical pumps, fuel-burring engines for domestic water, livestock and irrigation. They are most effective during dry and sunny seasons. They require no fuel deliveries and very little maintenance. Solar pumps are powered by photovoltaic panels and the pump controller which is with built in MPPT charge controller to harvest maximum power from solar panels. Models available: 1HP to 10HP (Built in auto change over the main power)

• Rate voltage: 220 V- 240 V, 110 V- 120 V, 110 V- 230 V
• Frequency: 50/ 60 Hz
• Max Current: 10 A
• Max Power: 1.1 kW, 1.5 kW, 2.2 kW
• Initial Pressure: 1.2 bars, 1.5 bars, 2.2 bars
• Max Pressure: 10 bar
• Interface Thread: R1
• Protection Class: IP65
• Max working temperature: 60° C
• Cable Specifications: 7.5- 9 mm

• Voltage: 250 To 520 Volts
• Feature: Micro Controller based Technology,Sleep Mode facility,
• Brand Name: Kirloskar
• Suitable for Pumps: Up to 50 HP
• Current Setting: Up to 70 Amp.
• Off Timer: 5 min to 720 min
• Phase: 1-5 HP (3 Phase)
• Model: DOL-ER
• Existing Starter Panels: UNI130 Universal Pump Controller

• Input Supply: 3 Phase 415 V, 50 HZ AC
• Input Current: 0-18 phase
• Display: 7 Segment ,4 digit

Water Level Controller is a state of the art instrument to control water pumps. It controls your pump as per levels in the overhead and underground water tanks and also guards your pump against power fluctuations(Over and Under Current)(for 3 Phase Pumps). It is a novel solution, ideal for all your water problems. Pump is Switched On when overhead tank is empty. It is Switched Off when either overhead tank is full or underground tank is empty. Water level controller cum indicator saves water and protects motor and reduces electricity bill. Our Automatic water level controller cum indicator serves 24 hours water supply without letting the overhead tank to become dry.

AC Solar Pump Controller, Solar BiDirectional Meter

we offer Pump Controller. Rising draught situations and inaccessibility to power have been one of the predominant challenges for rural economic progress in the country.

Solar Pump Controller, ONLINE UPS, Stabilizers, Solar Inverters

we offer Mobile Pump Controller. IVRS and SMS based motor/pump control for agricultural use

Solar Ac Pump Controller, Solar Irrigation Pump

pump protection relays level controllers, Agro Products

pump controllers, LED Street Light, LED floodlight, Led High Bay Light