Digital Indicator Dealers in Bhosari, Pune

The PI - 100 D series is a compact sized Process Indicator, designed to accept input from any two wire or four wire Transmitter. It has a seven segment, ½”, bright LED Display to read the Process Value in terms of Engineering Units or percent as is desired. The alarms can be set anywhere from 0% to 100 % with both High or both Low or one High and one Low configuration. The Output , 4-20 mA proportional to PV is isolated from input and power connections   ADVANTAGES : • Compact in Size • Field Programmable Parameters. • Linear/ Square Root operation programmable. • 4 Digit Display available to monitor Process parameter • Value from -9999 to 9999. • Isolated 4-20mAD.C. output proportional to Process Variable. Process Indicator with Alarms, PI-100 series • Adjustable Two Alarm Settings with various options of Operation. • Transmitter Supply 24 Vdc suitable for • 2 wire as well as 4 wire Transmitter.   • Serial Interface with Computer through MODBUS RTU.

• Input : Electrical, RTD ( Pt - 100 ) or Thermocouple
• Transmitter Supply : 24 VDC
• Output : 0/4-20 mA or 0-10 VDC Optional ( isolated )
• Indication : 4, 5, 6 digit LED Display as required
•  : 16x2 LCD with back light
• Power Supply : 230/110 VAC, 24 VDC
• Accuracy : Better than ± 0.2 % of FS
• Alarms : 1/2/3 Nos.
• Interface : RS 485 / MODBUS RTU / ASCII
• Mounting : Panel / field

Specifications:  Display   4 digit non-contact (RPM indicator)   Bright red 0.5 seven segment display   Range 1 RPM to 9999 RPM Accuracy +1-1% of FS User programmable speed limit trip point with keypad 2 C/0 relay output rated for 5A@ 240VAC / 28VDC (Resistive) Accept NPN / PNP proximity switch inputs   Inputs 1 pulse per revolutions / Scale Factor Supply 110 V / 230VAC Dimensions

To decrease the pollution created by the dusty condition of the conveyor, Water spraying is done on the conveyor through the nozzles. when these nozzle are activated, Water is sprayed over the conveyor to settle down the dust. these nozzle are activated when the belt is in loaded condition. Hence, This belt loading monitor plays an important roll of ensuring the belt is running with the load and water is sprayed when the conveyor is running in loaded condition of the Belt.     Operation :   The extension stand of belt Loading Monitor is mounted in inclined position to the action of the spring. So that Rubber Roller remain upward & the proximity switch remain OFF. When the Belt is started with Load (material), The belt will press the Rubber Roller downward thereby lifting the Mechanical Flag in front of proxirnity switch. Than Proximity switch gives the signal that can be used as a sense of Belt Loading condition. This detection of the Roller is between 5mm to 30 mm

• Brand Name: Protocontrol

Belt loading monitor is a simple and robust device to detect loading of material on the belt conveyor. By using this contact condition like empty running, part running and full load running of conveyor is detected. Indication of empty running of conveyor is very important as it gives early warning of no loead. it consists of a roller assembly which is to be installed below the belt. Due to loading on the belt, the roller makes contact with the belt .the belt pushes the roller down and operates the limit switch contact. The contacts are used in control circuit for interlocking purpose. The enclosure for switch is cast al / dmc suitable for outdoor mounting. specifications: control supply: 230 v ac, 50 hz output: 2 c/o relay contact, rating 5 amp resistive at 230 v ac enclosure: field mounting ip 65, cast al

  PROCESS INDICATORS Series µCS 2000 Features Microcontroller based fully programmable Universal Input Available with large display sizes Upto two programmable set-points Isolated Retransmission Built-in two-wire transmitter supply Field Calibration from front key pad Built-in square root extraction Various Cutouts and sizes Single Chip design for ruggedness and low cost

Digital Temperature & Pressure have been developed &being manufactured.

• Features: Ease of Frequency setting with simple Addition & Subtraction, LED indications for healthy, unhealthy & no signal conditions, Monitors frequency of three signals - Sine, Square & Triangular
• Frequency Limit Control: 5 Hz to 135 Hz
• Wide Signal Input Voltage: 15 to 500 VAC

We are highly acclaimed amidst the clients for the excellent quality and reliability of our Digital Temperature Indicator. We have made a strong position in the market as the most credible Manufacturer and Supplier of Digital Temperature Indicator. Our Digital Temperature Indicator has many features such as high accuracy and efficiency, precise engineering, and it can also withstand maximum ambient temperature. Specifications Input sensorThermocoupleIron - constantan (Fe/con) : up to 400oC Chromel - Alumel (Cr/Al) : up to 1200oC and up to 1600oCRTD : Resistance Temperature Detector (Pt-100) low temperature & up to 400oCAccuracy : +/- 0.5% of FSDCompensation : cold junction compensation automatic for all thermocouple modelsRelay Output : one change over relay contact 5 AMP / 230 VAC ratingControl Action : on-off or time proportionalControl version : single set point or dual set pointPower supply : 230 VAC+/-105.50 HzMax. Ambient temp. : 55oCSetting : Keypad / Knob/Push to setSize : 48 x 48, 72 x 72, 96 x 96, 48 x 96

These hand held digital temperatures can be equipped with a Pt-100 RTD temperature sensor thermocouple Universal. We also supplies a wide range of other probes for this instrument. It typically runs on its standard 9VDC battery. A large 3.5 digit LCD display shows your reading. Very easy to operate..

Programmable Process Indicator, three phase energy meter

Programmable indicator, Programmable Preset Timer

loop power indicator, BAUMER PRESSURE SWITCH, LFFS Baumer Make Level Switches

Belt Loading Monitor, Vibratory Feeder Controllers, Heavy Duty Limit Switches

Attachable Pressure Indicator, WIKA Pressure Gauges

Digital Bar Graph Indicator

digital indicators, Pressure Transmitters, Temperature Transmitters, Gauges

Digimatic Indicator, propeller blades, Norton Abrasive Belt