Electrical Equipments Dealers in Kothrud, Pune

This is an invaluable aid in the effective understanding of the automotive air-conditioning process. The equipment is a car air conditioning unit, which incorporates a blower, evaporator and air damper with a control chamber. The trainer is designed to bring out the specific constructional features of an automotive air-conditioning system and to study the performance characteristics. There is a facility to run the system with an electrical motor or an IC engine. It has a facility to measure various parameters like temperature at different points, pressure at different points, refrigerant flow rate, etc.

• Brand Name: N. P. Electronics
• Condition: Good
• Product Name: Road Test Equipment
• Feature: Speed,acceleration,braking distance,braking time distance,traveled test time,rpm fuel,Wheel Slip.
• Place Of Origin: Pune,Maharasthra

we are offering road testmeasuring equipments.a small unit with suction cup contains a light sensitive sensor as well as signal processing circuitry. The sensor responds only to a sudden increase in light intensity which will occur when the brake light comes on. Slow changes of light intensity will not trigger any start signal. Direct sunlight is shielded off by the black suction cup. In short: with the test start unit sticking on the stop light, a sudden increase of light intensity inside the brake light case will generate a short pulse which is recognized by the system as closure of a normally open contact – like a pedal switch contact.mountingmake the suction cup stick to the car’s brake light such that it intercepts the brake light’s rays. In case the stop light glass should be very much curved or rounded, an adhesive tape may be used in addition. A dark adhesive tape may also increase light contrast registered by the sensor. Make sure the connecting cable is firmly attached to the car body by means of adhesive tape. Lead this thin cable to inside the car through the padding rubber of the car’s door. Connect the cable to the“brake” or “ext. Startstop” connections of the peiseler test system.road test equipment testing solution for speed acceleration braking distance braking time distance traveled test time rpm fuel consumption wheel slip monitoring of transportation.

The range of air conditioning laboratory equipment is exclusively available with us who are up to the mark in terms of quality & its functions. Air conditioning lab equipment is designed with the special care & attention so that it can give its best performance under the opposite condition. The best part is that the air conditioning laboratory equipment offered by us is in accordance of the Indian & international quality standards. In addition, we are the leading air conditioning lab equipment manufacturer and exporters from India. RAC-04 Introduction �EEE� Air conditioning Cycle Demonstration Unit i.e. �EEE� Mini Air Conditioning Tutor is designed to carryout following experiments and study of air conditioning cycle in details for the students of Mechanical Engineering or Polytechnics. RANGE OF EXPERIMENTS 1. To demonstrate the basic Vapour Compression Cycle of Refrigeration. 2. To study theoretical cycles and plotting of T- and P.H. charts. 3. To study the properties of refrigerant at salient points of the cycle. 4. To find out refrigerating effect and work input, hence, actual and theoretical C.O.P. 5. To study functioning of vapour compression cycle at various evaporator temperatures. 6. To study compressor efficiency at varying functioning condition. This equipment is fully instrumented to demonstrate ' Refrigeration System ' with basic components and necessary controls. SPECIFICATIONS 1. Compressor - Hermetic Kirloskar make, Model AJ 11,Capacity 2355 Kcal/HR 2. Condenser - Air cooled suitable for above compressor with fan and motor 3. Evaporator - Suitable air cooled type fitted in the duct. 4. Expansion device - Thermostatic expansion valve Danfoss make orequivalent 5. Rotameter - for flow measurement of liquid refrigerant. Eureka make. 6. Refrigerant - R 22, charged with 1 ½ Kg, and extra : 2 kg 7. Energy meter - For power measurement of compressor , air heater and steamgenerator 8. Heater regulator - suitable capacity 9. Pressure gauge - Waree make, 2� dial, for HP and LP measurement. 10. Digital Temp. Indicator - For temp, measurement at various points.Range up to 300 C. 11. HPLP cutout - For safety of compressor, Ranco or equivalent make. 12. Orifice & manometer Inclined manometer and orifice plate for airflow measurement 13. Steam Generator - For steam injection. 14 Axial Fan - For forcing the air in the duct, 100 cfm 15. Air heater - 3 Nos, 0.5 KW capacity. 16. Dry - Wet bulb thermometer Zeal England mercury type for measurement of condition of air, 4 nos. 17. All equipment are suitably mounted on a painted sturdy angle frame and power coated panel. INSTRUCTION MANUAL An instruction manual is supplied with the apparatus which describes theory involved, range and procedure of experiments, along with necessary calculatons. SERVICES REQUIRED AC 220V 50 HZ supply. Space required : A bench area of approximately 5 m X 2 m. RAC-05 Introduction Heat pump is a machine which extracts heat from low grade heat sources and with addition of high grade energy in the form of electric motor or engine and delivers heat at a temperature. Suitable for either domestic, industrial or commercial purpose. EEE has designed Air and Water Heat Pump to demonstrate and analysis the cycle using refrigeration as a working fluid. The refrigeration cycle consists of Hermetically sealed compressor, water cooled condenser, filter/dryer, rotameter, thermostatic expansion valve, air evaporator and water evaporator with selector valves. Two additional rotameters are provided in water circuits of condenser and evaporator respectively to measure flow rates. Digital temperature indicator is provided to measure temperature at various position. THE LOW GRADE HEAT INPUT will be supplied by ambient air in the case of air evaporator or water in case of water evaporator, the HIGH GRADE ENERGY input will be supplied in the form of electrical energy to compressor. The amount of this input can be measured using energy meter. This tutor has been designed to achieve steady state within reasonable period so that students can complete their experiments within 2-3 hours. By varying operating conditions the performance of heat pump can be studied. SPECIFICATIONS 1) Compressor :- Hermetically sealed type Kirloskar make Ton capacity. 2) Condenser :- Water cooled type shell and coil condenser with refrigerant inside the tube. 3) Expansion valve :- Thermostatic Expansion valve. 4) Filter/ Dryer of suitable capacity. 5) Rotameter :- One for refrigerant circuit for R-12. One water Rotameter for condenser. One water rotameter for water evaporator. 6) Evaporator :- a) Water cooled type shell &coil evaporator with Refrigerant inside the tube. b) Air evaporator- finned tube type with fan and motor. 7) Multichannel Digital Temperature Indicator with Thermocouples to measure various temperatures. 8) H. P. L. P cutout. 9) Pressure gauge :- Two nos. For delivery and suction pressures. 10) Energy meter :- To measure power consumption of compressor motor. 11) Necessary valves, switches etc. 1/3 RANGE OF EXPERIMENTS 1) Determination of co-efficient of performance of unit when working as heat pump. 2) Energy balances for complete system over arrange of operating condition. 3) To determine overall heat transfer co-efficient for condenser and evaporator. 4) To observe effect of sub-cooling in the condenser on co-dfficient of performance of heat pump. INSTRUCTION MANUAL A technical Manual is supplied which gives details of the apparatus and procedure of experiments. SERVICES REQUIRED Single phase 230V. 15 Amp supply. Water supply continuous 20 lit/min. in two circuit for condenser and evaporator.

electrical distribution equipments

Level control system Maintaining the optimum level control system in the feed water tank is very important in order to ensure maximum temperature in feed water tank from condensate recovery & ensure the safety of the boiler. To achieve this without manual intervention, level control system is used. We offer a customized Level Control Systems for Boiler Feed water tank where hot condensate is preferred & utilized maximum, then hot water from any other sources & last preference to the cold make up water. This ensures that the energy of hot condensate & hot water from other sources is utilized

Air Conditioning Trainer, Engineering educational Equipments

industrial electrical equipment, Agricultural Equipments, Automobile Parts

electronics equipment, Automobile

electric equipments, Agricultural Products, Textile Fabrics

Electrical Equipments

Electrical Equipment, Battery, dry cells, Home Inverter, Inverter

Electrical Equipment, audio visual equipment, audio system, Projector Lamp

electronic testing equipment

Electronic test and measurement

Electrical Equipment, Right Angle Adapters, Chemical Earthing System

Electronic Equipments, Control Panel Board, Switch Gears

Electrical Equipment, electronics equipment, Hardware Products

electronics lab equipment, agro product