Expansion Joints Dealers in Pune

• Country of Origin: India
• Size: 2inch, 3/4inch, 3inch, 4inch
• Type: Fabric Expansion Joint
• Material: PVC COTED
• Shape: Equal, Round
• Application: Industrial Use, Machine Use, Pneumatic Connections
• Color: Silver, Gray
• Feature: Durable, Heat Resistant, High Strength, Leak Proof, Light Weigth
• Technics: Non Casting
• Finishing: Polished
• Certifications: ISI Certified

• Size: 3 Inch
• Material: Stainless Steel
• Shape: Round
• Color: Grey
• Feature: Durable, Dustproof, Easy To Use
• Pressure: UPTO 10PN
• Usage: Industrial

We are noted Manufacturer and Supplier of PTFE Expansion Bellows from Pune, Maharashtra. These bellows are manufactured by using optimum grade material and advanced techniques to meet the set industry norms. Our PTFE Expansion Bellows are designed so well that they can easily withstand extreme conditions. We can make available our PTFE Expansion Bellows in customized options as per buyer’s demand

This sort of extension joints are the least difficult and most practical joint. It is utilized where little warm developments exist. The prime point of preference of pivotal extension metal bellows is, the bearing of the stream is bidirectional alongside their minimal size. These bellows are generally made in SS304L, SS316L, SS316Ti and SS321. If there should arise an occurrence of extraordinary prerequisites they can be made in Inconel and other nickel based combinations. Axial expansion metal bellows should be installed co-axially with the pipes centerline. The purpose of this bellows is to compensate axial movements. With the existence of axial movements desired cyclic life can be achieved. If incase there exist other movements like angular or lateral this will affect the cyclic life of Bellows. Generally there expansion joints are used between straight pipes where movement is parallel to the centerline of pipe line. So in short one should use these bellows in following circumstances:   • Movement compensation is in straight line. • Minute lateral/Angular movement can be adjusted but will affect the cyclic life of the expansion joint. • Bellows are not designed to absorb rotary movements. • Due to the line pressure between the piping systems numbers of expansion joints are required. • The best piping system is the once which is broken between intermediate stages with metal bellows at each stage   In case if the expansion/contraction rate is higher than the bellows capacity 2 Bellows with a center foot in between can be used. There 2 bellows are placed between the center of the pipes so that the axial movements from each ends of pipe can be absorbed by the respective bellows. One should note in case of cryogenic application the pipe expansion joint will be stretched as the piping system will contract.

• Type: Industrial Joints
• Material: Aluminum, Stainless Steel
• Shape: T-Shaped
• Application: Robotic Joints
• Grade: JIS
• Color: Black, Grey
• Condition: New
• Finishing: Polished
• Structure: Double
• Country of Origin: India

• Application: Industrial
• Material: Rubber
• Color: Black
• Thickness: 1-1.5 inch
• Brand: GE
• Hardness: 30 to 80 ShoreA

We offer Polysulphide Sealant, which is perfect for low modulus pitch. Polysulphide is also suitable for sealing horizontal movement joints in concrete paving associated with airfields, motorways, bridge decks, car parks, warehouse and industrial flooring.  

Protective element for shaft joints, piping systems performing angular of axial movements.

• Material: Stainless Steel
• Shape: Round
• Thickness: 10-15mm
• Color: Grey
• Feature: Cost-effective, Durable
• Technics: Casting

• Size: Standard
• Type: Expansion
• Material: Carbon Steel, Iron
• Shape: Round
• Application: Industrial Use
• Thickness: 5-10mm
• Color: Black, Grey
• Condition: New
• Feature: Durable, Easy To Use, WaterProof

• Country of Origin: India
• Material: Brass
• Application: Industrial
• Color: Golden
• Finishing: Polished
• Technics: Machine Made

When axial deflections exist, and anchoring is impractical for fundamental or commercial reasons, such as long in the air or short straight pipe runs among two large vessels, the inline pressure balanced pipe expansion joint manufacturing is a powerful solution to a difficult design problem. The main factor of this flexible joint bellows type of unit is essentially the same as the elbow pressure balanced type, in that the axial pressure thrust is reacted by the pressure acting on a cross-sectional area equal to the area of the working or primary bellows. Inline Pressure Balanced Expansion Joint is designed to absorb axial, lateral and angular deflection. Since this unit is entirely axial, and there are no directional changes in the pipe, such as with the elbow, the cross-sectional area needed to balance the pressure is placed around the outside of the unit. Since the high-temperature pressure forces are generated by the pressure acting on the annular surface between the primary and outer, or balancing bellows, the arrangement of the tie rods shifts balances the load thrust produced in the pipe on each edge. Now the forces needed to compress or extend the unit are only the result of the spring resistance of the bellows, and main anchoring of the pipe or vessels is not required. These expansion joints are expensive than the other pressure balanced expansion joints however, they may result in a lower overall system cost when the elimination of main anchoring is considered. This expansion joint bellows designs can also be used to replace pipe loops, and its cost advantage may be seen in reduced pumping energy by the elimination of the loop's elbow-generated pressure losses. This may also allow reducing the pipe size for the entire system. As a trusted inline pressure balanced expansion joints global exporters, we always give assurance & material satisfaction to the customer. APPLICATIONS:   For replacing pipe loops For reduced pumping energy  

Architectural Expansion Joint - BnG Expansion Joint or movement joint is an assembly designed to safely absorb the heat– induced expansion and contraction of construction materials, to absorb vibration, to hold parts together, or to allow movement due to seismic events Building faces, concrete slabs, expand and contract due to warming and cooling from seasonal variation, or due to other heat sources. Before expansion joint gaps were built into these structures, they would crack under the stress induced . 

Stainless Steel Bellows offered for controlling the forces as well as stresses related to increasing as well as decreasing dimensional changes because of thermal expansion or contraction in structures involving ducting, vessels, piping and other end forms which are then transmitted to anchors and connected equipment. Needing less space in comparison to bends and loops, the superior flexible support provided by these bellows involves optimum absorption of movements in more than one direction.

We manufacture a wide range of Bellows in various shapes and sizes, which are long lasting and suitable to every application. A Bellow is a device used for delivering pressurized air in a controlled quantity to a controlled location. Materials Our Bellows are manufactured from superior quality synthetic materials and are long lasting and it can withstand temperatures up to 1000 C and are resistant to all cutting oils and coolants etc., MATERIAL USED Nylon Fabric coated with polyurethane, High Tensile Polyamide Fabric, Canvas, Leathered. Mounting Bellows are mounted and removed easily. Split type designs ensure the same. No costly down time for maintenance. Fixing options to suit individual machine are available. DIFFERENT SHAPES Round, Square, Rectangular, Octagonal, Odd Shapes.

SS Flap Bellows for Mazak & Hass MachinesSS Flap Bellow For Mazak & Hass Machine. It is working as sliding cover of Vertical movement.