Guru Enterpreses Hadapsar, Pune, Maharashtra

Aftercooler, Intercoolers, Oil Coolers, Condensers And Chillers Water Cooled After Cooler It is a heat Exchanger designed and manufactured to reduce / cool the compressed air temperature to desired level, so the condensation takes place and vaporized moisture and oil in the air gets converted to liquid droplets which further separated by moisture separator. The after Cooler substantially reduces the moisture and oil load coming to down stream at the initial stage. the cooling media can be water of air.   Features   Shell and tube and Tube in tube coolers Vertical / Horizontal models up to 2000 cfm at 12 kg / cm2 Operating pressure As per standards of national and international

The traditional refrigeration type air dryer does not provide sufficient air quality required for special applications. Guru regeneration heat less dryer contains smooth uniform achieved alumina balls size tat prevents channeling of compressed air flow, which maintains low bed velocities. This maintains air contact time for efficient moisture removal and minimal pressure drops.   SALIENT FEATURES OF SANPAR ECODRAIR SED SERIES. • Air Cooled • Tube in Tube Air-to-Air Heat Exchanger • Tube in Tube Evaporator • Hermetically Sealed Compressor • Air Cooled Condenser • Modulating capacity controller - 0 100% Thermal Load Handling • Eco-friendly refrigerated R134 a • Fan Pressure Switch • Capillary Tube Expansions • Capacity 5 to 50 cfm • Operating pressure: 4 to 16-bar g.

Low expansion aluminum alloy piston with international standard piston rings for positive sealing are elevated temperatures. All Air receivers are hydro-pressure tested and all compressors are tested for specified cycles in final assembled condition. Fan Agro dynamically designed fan with large blades for higher air flow.

Piston and Rings: Low expansion aluminum alloy piston with international standard piston rings for positive sealing are elevated temperatures. Crank Case and End covers: High quality graded cast iron. Cylinder: Special cast iron, deep finned for quick heat dissipation. Finger Valves and Disc Valves: Special hardened, ground lapped stainless steel for longer durability & less wear and tear. Air Receivers: All Air receivers are hydro-pressure tested and all compressors are tested for specified cycles in final assembled condition. Fan Agro dynamically designed fan with large blades for higher air flow.

SALIENT FEATURES OF SANPAR MOISTURE SEPARATOR • Very high Efficiency ( more than 99%) • Non-corrosive Aluminum die cast body • Compact Design • Maintenance Free • Long life • Manual drain and auto drain facility

  Get Rid of moisture Problem & Save Energy Upto 5 %     The actual pressure drop across After cooler is always high i.e. 0.5 kg/cm2 which means compressor has to compress 0.5 kg/cm2 more to deliver required pressure. This causes increase in Shaft Horse power by 3%. We design customised after coolers for your compressor so that pressure drop is less than 0.1 kg/cm2. This stright way gives saving of 3% and simple pay back on your investment is less than one year. The Moisture separators supplied by compressor manufacturers are low cost baffle type design. These are ineffective and causes more pressure drops. Moisture gets carried over to Air Dryer or to the plant.   This ultimately results in more power consumption for air dryer plant and more breakdowns of pneumatic tools due to moisture problem and hence more maintenance cost. Our centrifugal moisture separators are designed for very low pressure drop i.e.120 mm 0 WC (0.01 kg/cm2) and maximum moisture separation due to whirling action which removes up to 90 % of the moisture before air reaches to air dryer or plant.  

Heat less dryer works on the principal of absorption. Regenerative air dryers use desiccant media absorbs moisture contaminate from compressed air. The desiccant media can be regenerated by purging air and remove moisture it collect and remove again and again. So the dryness of the compressed air achieved up to atmospheric -40'c dew point. The traditional refrigeration type air dryer does not provide sufficient air quality required for special applications. Guru regeneration heat less dryer contains smooth uniform achieved alumina balls size tat prevents channeling of compressed air flow, which maintains low bed velocities. This maintains air contact time for efficient moisture removal and minimal pressure drops. Guru have electronic control timer for pneumatically pilot valves are chosen for long life and high air flow. A pre filter, oil removing filter, after filter offering purification to 5 micron can be specified purge loss and pressure drop are kept at a minimum resulting in lower operating costs.

Heat less dryer works on the principal of absorption. Regenerative air dryers use desiccant media absorbs moisture contaminate from compressed air. The desiccant media can be regenerated by purging air and remove moisture it collect and remove again and again. So the dryness of the compressed air achieved up to atmospheric -40'c dew point. The traditional refrigeration type air dryer does not provide sufficient air quality required for special applications. Guru regeneration heat less dryer contains smooth uniform achieved alumina balls size t\at prevents channeling of compressed air flow, which maintains low bed velocities. This maintains air contact time for efficient moisture removal and minimal pressure drops. Guru have electronic control timer for pneumatically pilot valves are chosen for long life and high air flow. A pre filter, oil removing filter, after filter offering purification to 5 micron can be specified purge loss and pressure drop are kept at a minimum resulting in lower operating costs.   Working Principle       During an operating cycle inlet air directed to pre filter, here moisture and dust particles are removed then air enters to oil removing filter here we remove flooded oil. As wet air flows through the desiccant tower bed the twin tower design of our dryers allows simultaneous compressed air drying and desiccant regenerated without interruption to the compressed air flow. At the end of the drying cycle the regenerated tower is re-pressurized and tower operation is reversed automatically. After tower change over wet inlet air is directed to the regenerated tower and the previously used desiccant is regenerated by the same process. A complete cycle of drying and regeneration is 10 minutes or 6 minutes timing is precisely controlled by Guru electronic timer.   Features   Applications Easy dry series designed for pharmaceuticals, powder coating, Spray Painting, CNC Machine, CMM Printing Application units etc.,   Range   • 5 cfm to 50 cfm- Easy dry series • 20cfm to 500cfm - Heatless dryer • Compact design   • Pre filter oil removing filter, after filters are standard   • Full instrumentation packages   • Counter flow drying and regeneration   • Low pressure drop less than 3 psi at rated flow   • Automatic re-pressurization   • Fixed purge orifice

SALIENT FEATURES OF SANPAR XEROS DRYERS (SXD SERIES) • Latest Technology of aluminum plate type heat exchangers. • Plate type heat exchangers are compact and light in weight. • Latest technology of vacuum brazing used on the plate type heat exchangers • Heat Exchangers put to helium leak test up to 27-bar g. • Optimum selection of compressor with high COP contributes to power benefits. • Victaulic couplings provided on the compressed air inlet and outlet connections for easy maintenance. • Negligible pressure-drop in the refrigeration line; hence utilizing complete rated cooling capacity of the compressor. • Heat Exchangers easily retrofitted without affecting the refrigeration line.    Rotolocks at the refrigerant inlet and outlet. • Refrigeration piping leak tested with electronic detectors ensuring that the leak is of the order of 3 g/year. • RS 232 port with interface software provided as an optional feature for remote monitoring. • Capacity: 50 to 10,000 cfm. • Operating Pressure: 3 to 14 bar g

The desiccant media can be regenerated by purging air and remove moisture it collect and remove again and again. So the dryness of the compressed air achieved up to atmospheric -40'c dew point. The traditional refrigeration type air dryer does not provide sufficient air quality required for special applications. Guru regeneration heat less dryer contains smooth uniform achieved alumina balls size tat prevents channeling of compressed air flow, which maintains low bed velocities.

NO AIR LOSS FLOAT TYPE AUTO DRAIN The SFD320 is an automatic mechanical float type drain made of cast Aluminum body • That contains a stainless steel float ball • It discharges only the condensate automatically (not the compressed air). • It is also equipped with a manual drain valve for manual operation. • The drain is provided with a standard ½” BSP connection. DRAINS SANPAR TIMER DRAIN Sanpar make Timer Drain consists of a strainer with a solenoid valve. The drain valve opens based on the timings set in the drain. Also the time interval between the successive openings of the valve can be set. The drain has a standard ½” BSP connections.

Features Stores the Pressurized Compressed Air Helps to maintain constant Pressure at downstream Cools the compressed air Helps to separate oil & moisture from compressed air To allow com pressured have optimum level of rest Hand and man holes Provided as per standards Range Range from 0.10 to 10m3 Vertical and Horizontal type As per standards of national and international pressure vessels code

Sanpar brings to you the state of the art compressed air filters. These filters are aptly designed to take care of the problems related with the dust and oil contaminants. The elements are assembled in a compact Aluminum Die cast housing. Sanpar Manufacturers Five Grades Of Filters. 1. Primary Pre filter PPF (Pleated SS mesh) : 25-micron filtration capacity. 2. Pre Filter PF (Pleated Cellulose Acetate) : Bulk liquid and partial removal down to 3 micron. 3. After Filter AF (Borosilicate glass fiber) : Liquid and partial removal down to 0.1 micron,     residual oil content 0.5 mg/m3. 4. Final Filter FF (Borosilicate glass fiber : Liquid and partial removal down to 0.01 micron,     residual oil content 0.01 mg/m3. 5. Carbon Filter CF (Activated Carbon Granules) : Liquid and partial removal below 0.01 micron,     residual oil content 0.005 mg/m3. Free of odour and oil vapour.