Measurment Systems of Liquids & Gases Alandi, Pune, Maharashtra

We offer Wet Gas Meter within the working range of the meter the rotor spins proportional to the actual velocity of gaseous material flowing. A pick-up sensor produces an electrical signal as each blade crosses through its low magnetic or rf field. This signal is amplified and conditioned by a transmitter or fed directly into a rate/totalizer, and represents the actual cubic feet per minute (acfm) flowing through the meter. The k-factor is stenciled on the meter body in pulses per actual cubic feet (p/acf). Because gases are compressible, most people desire to measure the equivalent amount of gas corrected for the line pressure and temperature to standard cubic feet per minute (scfm at 60â°f, 14.69 psia). If the flow temperature and pressure are relatively constant, then a simple correction can be calculated to shift the k-factor from p/acf to p/scf and a simple totalizer (measurement systems india make ) may be used. When flow temperature and pressure are not constant, a flow computer. specifications linearity 1 â±1.0%/0.5% repeatability 1 â±0.25% maximum over-range 125% of flow rate for intermittent periods frequency output 0 to 1,100 hz voltage output approximately 100 mv@ 100 hz to 1.5 v (rms)@ 1,000 hz. Pressure drop 0.5 psi at 100% of flow range pressure rating we manufacture flowmeters for most pressures. installation vertical or horizontal (any direction). Materials of construction body: 316 l stainless steel. Flanges: 316 stainless steel rotor: 431 stainless steel. Rotor shaft/bearings: standard: tungsten carbide v-cup cartridge frame retainer: 302 stainless steel cartridge frame: 316 l stainless steel. Temperature range:meter with bearing structure of: standard: tungsten carbide: -40â°f to 300â°f (-40â°c to 149â°c). For other temperatures consult factory.

Measurement Systems Rotor Flow Sensor Provide Visual Indication, Continuous Sensing and Accurate Switching Bright, Visual indication with choice of pulsed DC output, or adjustable 1 amp switched output. Flow ranges from 0.5 LPM to 60.0 LPM Compact inline housings Available in high performance plastic, brass, or stainless steel housings. Determined to provide you with the most versatile line of flow sensors available, we've continued a non-stop refinement process for the entire Measurement Systems Rotor Flow Sensor Series. Gems™ new generation of Measurement Systems Rotor Flow Sensor sensors, the Measurement Systems Rotor Flow Sensor-2500 Series, have been totally re-engineered with a one piece composite rotor, stronger unibody construction, ceramic shaft and better sealing. The results are greater durability with broader chemical, temperature and pressure capabilities. Today's Measurement Systems Rotor Flow Sensor Series is state-of-the art and offers more options, better performance and durability than ever before...all at an affordable price geared for high volume, OEM applications. Select the Measurement Systems Rotor Flow Sensor that is right for your application by choosing one of our three distinct configurations. You'll find details on each of these configurations inside. Switch Types For specific flow setpoint switching, Measurement Systems Rotor Flow Sensor RFS type stitches are one of the most reliable flow switches available. Setpoints are fully adjustable over the specified flow range. The dynamic operation of the rotor guards against jamming and false actuation. Output Types For flow rate monitoring or metering applications. Measurement Systems Rotor Flow Sensor RFO Type sensors provide a pulsed DC voltage output that is proportional to the rate of flow. The operating range of 4.5 to 24 VDC pulsed output is easily integrated into most digital logic units. RFA Type Measurement Systems Rotor Flow Sensor sensors provide a continuous 0-10 VDC analog output. Indicator Types For those who want simple visual confirmation of flow, Measurement Systems Rotor Flow Sensor RFI indicators provide the durable, low-cost answer. A bright, orange spinning rotor provides visual flow confirmation at a glance.

the m s group venturi flow element design, developed and perfected by us is a proprietary design offered exclusively by the company for high accuracy and high reliability flow measurement of pressurized line fluids including liquids, gasses, and steam. in its embodiment as the ms group sealed metering system, this revolutionary design accommodates flow measurement of high viscosity line fluids, solids bearing line fluids as well as harsh and/or contaminated line fluids. this design is also available in the rectangular configuration for conduits shaped thusly. this design is available in a variety of configurations, including cast iron pressure vessel, fabricated (welded) metal pressure vessel, plastic insert style, welded insert style, and welded-in pressure vessel style. additionally, the ms group is offered as a cast in place (usually concrete and typically rectangular) configuration. pfs, inc. applications specialists can help you select

venturi flowmeters for most liquids,slurries,gas applications .

we manufacture this type of flowmeters for pharmaceuticals,sanitary,chemical industry applications which requires stainless steel 316l body only. also some flowmeters are manufactured in teflon and other materials as per requirements if required for cost effectiveness and light weight. the above flowmeter has a turbine of ss316l

Prepaid gas meters.

This type of flow meter has oval shaped gears/ with fitting teeth which control the amount of fluid passing through. The flow rate is calculated by number of times the gears are filled and emptied. These meters have high accuracy and are used for measuring low flow and for high viscosity fluids. It is very easy to install these types of meters because it requires no pipe. Two identical oval rotors mesh together by means of slots around the gear perimeter. The oval shaped gears are used to sweep out an exact volume of the liquid passing through the measurement chamber during each rotation. The flow rate can be calculated by measuring the rotation speed. Close tolerances ensure that leakage is minimized. In contrast to nutating disc meters, the calibration factor does not vary with viscosity. Though claims for high performance are made, oval gear flowmeters are generally not as precise as the sliding vane design. Another disadvantage is that pulsations are introduced into the flow by the meter. Oval gear meters are typically used in the measurement of solvents and 'dry' liquids. Maximum viscosity allowed: 1,000 centipoise. Other Information Pay Mode Terms: Other Minimum Order Quantity: 01 Piece/Pieces Port of Dispatch: Nhava Seva Production Capacity: 30/month Delivery Time: 1-2 weeks Packaging Details: One Flowmeter In One Wooden Box

are you looking for a high pressure flowmeter? 500bar, 1000bar, 2000bar, 4000bar. contact the specialists! litre meter have tailor-made solutions for many high pressure applications using various technologies: positive displacement; turbine, pelton wheel, gas and ultrasonic flow meter. proven over many years. installed throughout the world. made to measure. if you are looking for accurate, reliable flow measurement litre meter has all the expertise you need. we manufacture pelton wheel turbine flowmeters and rotary piston positive displacement flow meters. we distribute thermal mass gas flowmeters; helical screw positive displacement meters; electromagnetic flowmeters; drum type gas meters; vortex flowmeters; ultrasonic flowmeters and axial flow turbine flow meters. mass flowmeters, water flowmeters and chemical flowmeters (for chemical injection) are all available. with over 10 years experience in designing, manufacturing and supplying high performance flowmeters, we are able to offer a broad range of technologies suitable for virtually every liquid,gas or steam measurement application. based in the uk we serve the flowmeter market either direct or through our large network of distributors. our flow meters are manufactured in india to the highest quality and standards and are used across the world - from the harshest conditions found sub-sea to the precision of laboratory conditions. we have particular expertise in measuring low flow rates. whether you need water flow meters or chemical injection flow meters consult the specialists. alongside our engineering capabilities, we have also built a reputation for providing a fast, reliable service. we are able to offer a total flowmeter service that is among the best in the industry. with a selection of six calibration rigs in-house and dozens available from our partners worldwide we can answer all your flow questions. applications we cover: low viscosity liquids pelton wheel flowmeters intrinsically safe flowmeters positive displacement flowmeters electromagnetic flowmeters high viscosity liquids rotary piston meters for accurate low flow metering screw flowmeters gas flowmeters thermal mass gas flowmeters gas flow meters - volumetric oil industry flowmeters vff rotary piston meters for chemical injection and hydraulics measurement pelton wheel for low flow flow tech turbine meters high pressure flow measurement to 4000 bar / 60000 psi subsea flow measurement chemically resistant flowmeters constructed entirely from titanium, pfa, pvdf, pp or pvc

the mini-flow flow measuring instruments of the measurement systems oil meter series are especially suitable for measuring low viscous liquids starting from 0.015 litre /min- 8,0 litre/min. like: gasoline, diesel, vegoil, kerosine, ethanol, methanol or other non aggressive liquids. application: for example as fuel flow meter, flow meter for diesel, biodiesel, lubrication oil, oil flow meter, fuel flowmeter / fuel flow meter, oilflowmeter, fuel flowsensor, diesel oil flowmeter, lubrication oil flow meters, flowsensor, meters, fuel flowmeter, flow sensors, diesel flowmeter. depending on the size of the nozzle, d= 0.2 mm – 4.5mm maximal, our mini flow meters can be retooled for lower rates of flow q= 0.005 l/min up to 8 l/min. ideal as fuel flowmeters, oil flowmeters, for fuel consumption measuring -in combination with the totalisor ars 260 or ars 261 - on stationary and moblie combustion engines. process connector electrical connection-230 v ac connector ip 65 round or flat ribbon cable silicon / teflon cable signal output:4-20ma and special pulse output type. led integrated (optional) equipment mounting plate from high- grade steel or aluminum flow monitor, totaliser currently consumption indicator differential analysing unit for measuring 2 flowmeters

Measurement Systems Rotor Flow Sensor Provide Visual Indication, Continuous Sensing and Accurate Switching Bright, Visual indication with choice of pulsed DC output, or adjustable 1 amp switched output. Flow ranges from 0.5 LPM to 60.0 LPM Compact inline housings Available in high performance plastic, brass, or stainless steel housings. Determined to provide you with the most versatile line of flow sensors available, we've continued a non-stop refinement process for the entire Measurement Systems Rotor Flow Sensor Series. Gems™ new generation of Measurement Systems Rotor Flow Sensor sensors, the Measurement Systems Rotor Flow Sensor-2500 Series, have been totally re-engineered with a one piece composite rotor, stronger unibody construction, ceramic shaft and better sealing. The results are greater durability with broader chemical, temperature and pressure capabilities. Today's Measurement Systems Rotor Flow Sensor Series is state-of-the art and offers more options, better performance and durability than ever before...all at an affordable price geared for high volume, OEM applications. Select the Measurement Systems Rotor Flow Sensor that is right for your application by choosing one of our three distinct configurations. You'll find details on each of these configurations inside. Switch Types For specific flow setpoint switching, Measurement Systems Rotor Flow Sensor RFS type stitches are one of the most reliable flow switches available. Setpoints are fully adjustable over the specified flow range. The dynamic operation of the rotor guards against jamming and false actuation. Output Types For flow rate monitoring or metering applications. Measurement Systems Rotor Flow Sensor RFO Type sensors provide a pulsed DC voltage output that is proportional to the rate of flow. The operating range of 4.5 to 24 VDC pulsed output is easily integrated into most digital logic units. RFA Type Measurement Systems Rotor Flow Sensor sensors provide a continuous 0-10 VDC analog output. Indicator Types For those who want simple visual confirmation of flow, Measurement Systems Rotor Flow Sensor RFI indicators provide the durable, low-cost answer. A bright, orange spinning rotor provides visual flow confirmation at a glance.

We have Natural Gas Meter within the working range of the meter the rotor spins proportional to the actual velocity of gaseous material flowing. A pick-up sensor produces an electrical signal as each blade crosses through its low magnetic or rf field. This signal is amplified and conditioned by a transmitter or fed directly into a rate/totalizer, and represents the actual cubic feet per minute (acfm) flowing through the meter. The k-factor is stenciled on the meter body in pulses per actual cubic feet (p/acf). Because gases are compressible, most people desire to measure the equivalent amount of gas corrected for the line pressure and temperature to standard cubic feet per minute (scfm at 60â°f, 14.69 psia). If the flow temperature and pressure are relatively constant, then a simple correction can be calculated to shift the k-factor from p/acf to p/scf and a simple totalizer (measurement systems india make ) may be used. When flow temperature and pressure are not constant, a flow computer. specifications linearity 1 â±1.0%/0.5% repeatability 1 â±0.25% maximum over-range 125% of flow rate for intermittent periods frequency output 0 to 1,100 hz voltage output approximately 100 mv@ 100 hz to 1.5 v (rms)@ 1,000 hz. Pressure drop 0.5 psi at 100% of flow range pressure rating we manufacture flowmeters for most pressures. installation vertical or horizontal (any direction). Materials of construction body: 316 l stainless steel. Flanges: 316 stainless steel rotor: 431 stainless steel. Rotor shaft/bearings: standard: tungsten carbide v-cup cartridge frame retainer: 302 stainless steel cartridge frame: 316 l stainless steel. Temperature range:meter with bearing structure of: standard: tungsten carbide: -40â°f to 300â°f (-40â°c to 149â°c). For other temperatures consult factory.

Item Code: MS-Bi-Directional-Flow-Sensor Bidirectional Paddle flow switch use new structure, could monitor the flow by Two-way. It is operate by micro magnetic reed switch, it is normal Open, when flowing water push the paddle, the transfer structure change the switch condition, it close. This flow switch could be Anti Explosion-prrof. Specification: * Work Temperature: -30C – 150C * Max Pressure: 30bar * Output: 40W 250VAC/DC SPDT * Work Medium: water and oil * Pressure Loss: less than 0.01bar * Installation: 1”PT; Insert * Pipe Size: DN20~DN200 * Protect Grade: IP65 (GE-341C) * Explosion-Proof Grade: ExdIICT6 (GE-341B)

milk meter for all line sizes ,pressures,temperatures & all flow rates the flowmeters are compiatble of taking inlet milk with accuracy of 0.5% and the flowmeters can withstand 160 degree celcius so that they can be used for the cip,sip with an ease.

mass flowmeter with temperature and pressure compensation charasteristics. the flowmeter can be used for all the gases and liquids the flowmeters can be manufactured in the following types:1 1.turbine type mass flowmeters 2.differential pressure type mass flowmeters(non contact) 3.venturi type flowmeters also we can supply the flowmeters in ultrasonic types.if required,.

within the working range of the meter the rotor spins proportional to the actual velocity of gaseous material flowing. a pick-up sensor produces an electrical signal as each blade crosses through its low magnetic or rf field. this signal is amplified and conditioned by a transmitter or fed directly into a rate/totalizer, and represents the actual cubic feet per minute (acfm) flowing through the meter. the k-factor is stenciled on the meter body in pulses per actual cubic feet (p/acf). because gases are compressible, most people desire to measure the equivalent amount of gas corrected for the line pressure and temperature to standard cubic feet per minute (scfm at 60â°f, 14.69 psia). if the flow temperature and pressure are relatively constant, then a simple correction can be calculated to shift the k-factor from p/acf to p/scf and a simple totalizer (measurement systems india make ) may be used. when flow temperature and pressure are not constant, a flow computer. specifications linearity 1 â±1.0%/0.5% repeatability 1 â±0.25% maximum over-range 125% of flow rate for intermittent periods frequency output 0 to 1,100 hz voltage output approximately 100 mv@ 100 hz to 1.5 v (rms)@ 1,000 hz. pressure drop 0.5 psi at 100% of flow range pressure rating we manufacture flowmeters for most pressures. installation vertical or horizontal (any direction). materials of construction body: 316 l stainless steel. flanges: 316 stainless steel rotor: 431 stainless steel. rotor shaft/bearings: standard: tungsten carbide v-cup cartridge frame retainer: 302 stainless steel cartridge frame: 316 l stainless steel. temperature range:meter with bearing structure of: standard: tungsten carbide: -40â°f to 300â°f (-40â°c to 149â°c). for other temperatures consult factory.

We are offering Gas Meters, within the working range of the meter the rotor spins proportional to the actual velocity of gaseous material flowing. a pick-up coil produces an electrical signal as each blade crosses through its low magnetic or rf field. this signal is amplified and conditioned by a transmitter or fed directly into a rate/totalizer, and represents the actual cubic feet per minute (acfm) flowing through the meter. the k-factor is stenciled on the meter body in pulses per actual cubic feet (p/acf). because gases are compressible, most people desire to measure the equivalent amount of gas corrected for the line pressure and temperature to standard cubic feet per minute (scfm at 60â°f, 14.69 psia). if the flow temperature and pressure are relatively constant, then a simple correction can be calculated to shift the k-factor from p/acf to p/scf and a simple totalizer (measurement systems india make ) may be used. when flow temperature and pressure are not constant, a flow computer. specifications linearity 1 â±1.0%/0.5% repeatability 1 â±0.25% maximum over-range 125% of flow rate for intermittent periods frequency output 0 to 1,100 hz voltage output approximately 100 mv@ 100 hz to 1.5 v (rms)@ 1,000 hz. pressure drop 0.5 psi at 100% of flow range pressure rating we manufacture flowmeters for most pressures. installation vertical or horizontal (any direction). materials of construction body: 316 l stainless steel. flanges: 316 stainless steel rotor: 431 stainless steel. rotor shaft/bearings: standard: tungsten carbide v-cup cartridge frame retainer: 302 stainless steel cartridge frame: 316 l stainless steel. temperature range:meter with bearing structure of: standard: tungsten carbide: -40â°f to 300â°f (-40â°c to 149â°c). for other temperatures consult factory.

We can supply Gas Meter within the working range of the meter the rotor spins proportional to the actual velocity of gaseous material flowing. A pick-up sensor produces an electrical signal as each blade crosses through its low magnetic or rf field. This signal is amplified and conditioned by a transmitter or fed directly into a rate/totalizer, and represents the actual cubic feet per minute (acfm) flowing through the meter. The k-factor is stenciled on the meter body in pulses per actual cubic feet (p/acf). Because gases are compressible, most people desire to measure the equivalent amount of gas corrected for the line pressure and temperature to standard cubic feet per minute (scfm at 60â°f, 14.69 psia). If the flow temperature and pressure are relatively constant, then a simple correction can be calculated to shift the k-factor from p/acf to p/scf and a simple totalizer (measurement systems india make ) may be used. When flow temperature and pressure are not constant, a flow computer. specifications linearity 1 â±1.0%/0.5% repeatability 1 â±0.25% maximum over-range 125% of flow rate for intermittent periods frequency output 0 to 1,100 hz voltage output approximately 100 mv@ 100 hz to 1.5 v (rms)@ 1,000 hz. Pressure drop 0.5 psi at 100% of flow range pressure rating we manufacture flowmeters for most pressures. installation vertical or horizontal (any direction). Materials of construction body: 316 l stainless steel. Flanges: 316 stainless steel rotor: 431 stainless steel. Rotor shaft/bearings: standard: tungsten carbide v-cup cartridge frame retainer: 302 stainless steel cartridge frame: 316 l stainless steel. Temperature range:meter with bearing structure of: standard: tungsten carbide: -40â°f to 300â°f (-40â°c to 149â°c). For other temperatures consult factory.

We have Gas Flow Meters within the working range of the meter the rotor spins proportional to the actual velocity of gaseous material flowing. A pick-up coil produces an electrical signal as each blade crosses through its low magnetic or rf field. This signal is amplified and conditioned by a transmitter or fed directly into a rate/totalizer, and represents the actual cubic feet per minute (acfm) flowing through the meter. The k-factor is stenciled on the meter body in pulses per actual cubic feet (p/acf). Because gases are compressible, most people desire to measure the equivalent amount of gas corrected for the line pressure and temperature to standard cubic feet per minute (scfm at 60â°f, 14.69 psia). If the flow temperature and pressure are relatively constant, then a simple correction can be calculated to shift the k-factor from p/acf to p/scf and a simple totalizer (measurement systems india make ) may be used. When flow temperature and pressure are not constant, a flow computer. specifications linearity 1 â±1.0%/0.5% repeatability 1 â±0.25% maximum over-range 125% of flow rate for intermittent periods frequency output 0 to 1,100 hz voltage output approximately 100 mv@ 100 hz to 1.5 v (rms)@ 1,000 hz. Pressure drop 0.5 psi at 100% of flow range pressure rating we manufacture flowmeters for most pressures. installation vertical or horizontal (any direction). Materials of construction body: 316 l stainless steel. Flanges: 316 stainless steel rotor: 431 stainless steel. Rotor shaft/bearings: standard: tungsten carbide v-cup cartridge frame retainer: 302 stainless steel cartridge frame: 316 l stainless steel. Temperature range:meter with bearing structure of: standard: tungsten carbide: -40â°f to 300â°f (-40â°c to 149â°c). For other temperatures consult factory.

We offer Gas Flow Meter, within the working range of the meter the rotor spins proportional to the actual velocity of gaseous material flowing. a pick-up coil produces an electrical signal as each blade crosses through its low magnetic or rf field. this signal is amplified and conditioned by a transmitter or fed directly into a rate/totalizer, and represents the actual cubic feet per minute (acfm) flowing through the meter. the k-factor is stenciled on the meter body in pulses per actual cubic feet (p/acf). because gases are compressible, most people desire to measure the equivalent amount of gas corrected for the line pressure and temperature to standard cubic feet per minute (scfm at 60â°f, 14.69 psia). if the flow temperature and pressure are relatively constant, then a simple correction can be calculated to shift the k-factor from p/acf to p/scf and a simple totalizer (measurement systems india make ) may be used. when flow temperature and pressure are not constant, a flow computer. specifications linearity 1 â±1.0%/0.5% repeatability 1 â±0.25% maximum over-range 125% of flow rate for intermittent periods frequency output 0 to 1,100 hz voltage output approximately 100 mv@ 100 hz to 1.5 v (rms)@ 1,000 hz. pressure drop 0.5 psi at 100% of flow range pressure rating we manufacture flowmeters for most pressures. installation vertical or horizontal (any direction). materials of construction body: 316 l stainless steel. flanges: 316 stainless steel rotor: 431 stainless steel. rotor shaft/bearings: standard: tungsten carbide v-cup cartridge frame retainer: 302 stainless steel cartridge frame: 316 l stainless steel. temperature range:meter with bearing structure of: standard: tungsten carbide: -40â°f to 300â°f (-40â°c to 149â°c). for other temperatures consult factory.

turbine water flowmeters body material:ss316 l turbine material:ss316l flowmeters can be manufactured for all flows,pressures,temperatures and line sizes. we offer turbine flowmeters and mass flowmeters also for water applications.

within the working range of the meter the rotor spins proportional to the actual velocity of gaseous material flowing. a pick-up coil produces an electrical signal as each blade crosses through its low magnetic or rf field. this signal is amplified and conditioned by a transmitter or fed directly into a rate/totalizer, and represents the actual cubic feet per minute (acfm) flowing through the meter. the k-factor is stenciled on the meter body in pulses per actual cubic feet (p/acf). because gases are compressible, most people desire to measure the equivalent amount of gas corrected for the line pressure and temperature to standard cubic feet per minute (scfm at 60°f, 14.69 psia). if the flow temperature and pressure are relatively constant, then a simple correction can be calculated to shift the k-factor from p/acf to p/scf and a simple totalizer (measurement systems india make ) may be used. when flow temperature and pressure are not constant, a flow computer. specifications linearity 1 ±1.0%/0.5% repeatability 1 ±0.25% maximum over-range 125% of flow rate for intermittent periods frequency output 0 to 1,100 hz voltage output approximately 100 mv@ 100 hz to 1.5 v (rms)@ 1,000 hz. pressure drop 0.5 psi at 100% of flow range pressure rating we manufacture flowmeters for most pressures. installation vertical or horizontal (any direction). materials of construction body: 316 l stainless steel. flanges: 316 stainless steel rotor: 431 stainless steel. rotor shaft/bearings: standard: tungsten carbide v-cup cartridge frame retainer: 302 stainless steel cartridge frame: 316 l stainless steel. temperature range:meter with bearing structure of: standard: tungsten carbide: -40°f to 300°f (-40°c to 149°c). for other temperatures consult factory.

within the working range of the meter the rotor spins proportional to the actual velocity of gaseous material flowing. a pick-up sensor produces an electrical signal as each blade crosses through its low magnetic or rf field. this signal is amplified and conditioned by a transmitter or fed directly into a rate/totalizer, and represents the actual cubic feet per minute (acfm) flowing through the meter. the k-factor is stenciled on the meter body in pulses per actual cubic feet (p/acf). because gases are compressible, most people desire to measure the equivalent amount of gas corrected for the line pressure and temperature to standard cubic feet per minute (scfm at 60â°f, 14.69 psia). if the flow temperature and pressure are relatively constant, then a simple correction can be calculated to shift the k-factor from p/acf to p/scf and a simple totalizer (measurement systems india make ) may be used. when flow temperature and pressure are not constant, a flow computer. specifications linearity 1 â±1.0%/0.5% repeatability 1 â±0.25% maximum over-range 125% of flow rate for intermittent periods frequency output 0 to 1,100 hz voltage output approximately 100 mv@ 100 hz to 1.5 v (rms)@ 1,000 hz. pressure drop 0.5 psi at 100% of flow range pressure rating we manufacture flowmeters for most pressures. installation vertical or horizontal (any direction). materials of construction body: 316 l stainless steel. flanges: 316 stainless steel rotor: 431 stainless steel. rotor shaft/bearings: standard: tungsten carbide v-cup cartridge frame retainer: 302 stainless steel cartridge frame: 316 l stainless steel. temperature range:meter with bearing structure of: standard: tungsten carbide: -40â°f to 300â°f (-40â°c to 149â°c). for other temperatures consult factory.

We offer Diesel Flowmeter with lowest weight for custody transfer applications for decantation of tanker trucks to under ground tanks by gravity. he is looking for machine with accuracy rate 0.15%. flow meter has gravity transfer, variable flow and has robust design and is portable.

We have Diaphragm Gas Meter within the working range of the meter the rotor spins proportional to the actual velocity of gaseous material flowing. A pick-up sensor produces an electrical signal as each blade crosses through its low magnetic or rf field. This signal is amplified and conditioned by a transmitter or fed directly into a rate/totalizer, and represents the actual cubic feet per minute (acfm) flowing through the meter. The k-factor is stenciled on the meter body in pulses per actual cubic feet (p/acf). Because gases are compressible, most people desire to measure the equivalent amount of gas corrected for the line pressure and temperature to standard cubic feet per minute (scfm at 60â°f, 14.69 psia). If the flow temperature and pressure are relatively constant, then a simple correction can be calculated to shift the k-factor from p/acf to p/scf and a simple totalizer (measurement systems india make ) may be used. When flow temperature and pressure are not constant, a flow computer. specifications linearity 1 â±1.0%/0.5% repeatability 1 â±0.25% maximum over-range 125% of flow rate for intermittent periods frequency output 0 to 1,100 hz voltage output approximately 100 mv@ 100 hz to 1.5 v (rms)@ 1,000 hz. Pressure drop 0.5 psi at 100% of flow range pressure rating we manufacture flowmeters for most pressures. installation vertical or horizontal (any direction). Materials of construction body: 316 l stainless steel. Flanges: 316 stainless steel rotor: 431 stainless steel. Rotor shaft/bearings: standard: tungsten carbide v-cup cartridge frame retainer: 302 stainless steel cartridge frame: 316 l stainless steel. Temperature range:meter with bearing structure of: standard: tungsten carbide: -40â°f to 300â°f (-40â°c to 149â°c). For other temperatures consult factory.