Primer Paint Dealers in Pune

• Application: Interior Use, Painting Use
• Packaging Type: Can, Plastic Bottle
• Finish: High Gloss, Mild Sheen
• Packaging Size: 1-5 L, 10-15 L, 15-20 L, 20-25 L, 200ml

Shaf Sunrise Line Mark Pvt. Ltd. has a specially designed primer for application of Thermoplastic road marking material on concrete and old bitumen surface. The primer ensures excellent adhesion of the thermoplastic strips onto concrete or old bitumen, thereby increasing the life of road marking. Being quick drying and easy to apply, no significant time under-runs are expected owing to primer application. Colour - clear to translucent. Thermoplastic road marking paint, also called hot melt marking paint, is a powder base paint. When applied as road surface markings, need to heat upto 200 °C (392 °F), after which it is sprayed on the road surface. The coating then becomes a line after cooling. This paint is thick coating, wear-resisting, bright and reflective. In order to increase the antiskid performance of the line, thermoplastic paint has added reflective glass beads.The product is made up of selective use of plastic sized binders, reflective glass beads, extenders and pigments.General Characteristics Quick drying: The thermoplastic road marking paint should dry in a short time and no matter what climate it is. However the drying process is faster in winter than summer. It’s better to reduce the molten state temperature of the paint to cut down the hardening time. High durability: Compared to normal road paints, thermoplastic is hard wearing and is highly durable under all-weather all traffic conditions, its average life span is two to three years under normal traffic condition. Excellent adhesion: The thermoplastic road marking paint has strong connection with roads, it’s hard to break or peel off the paint from road surface. Coating agent is pre-painted to enhance the adhesion between thermoplastic road coatings and roads, that’s why their connection is so firm. Visual visibility: Whether it is day or night, thermoplastic road marking paint should be clear and visible within enough visual distance. It’s very easy to handle this in daytime since the visibility depends on the quality of the paint. But the visibility in the night depends on the reflective glass beads distribution and the temperature control during construction. For immediate effect, high Ratro reflective drop-on beads are recommended at the rate of 250 gm/sq.m. High skid resistance: Aggregate material of selected sizes are used in the product mixture and tested thoroughly to provide maximum required skid resistance for better road safety. High Softening Point: A good chemical formulation combined with years of Research and Development has yielded a product of exceptional stability against the effects of UV rays and harsh tropical climate conditions. Methodology for Application of Thermoplastic Road Marking Scope: This methodology is applicable for line marking on asphalt & concrete surface by using Thermoplastic Road Marking Material using Manual, Semi-automatic and Automatic Road Marking Equipment with attachment of Glass Bead Dispenser to spray Glass Beads. Machine: The work will be carried out by using fully automatic, semi-automatic or manual applicator machine. Pre-meltors for preparation of material will also be used to speed up the work and provide uniform pre-heating of the material, if necessary. The equipment used to lay hot applied thermoplastic material will be able to provide continuous uniform heating to temperatures of upto 200C, mixing and agitation of the material. Applications The Thermoplastic road marking will be executed by using Fully Automatic Machine or Semi-Automatic Machine. The thermoplastic material will be applied hot by Screening or Extrusion process. All surfaces to be marked will be thoroughly cleaned of all dust, dirt, grease, oil and all other foreign material before application of the marking. The lines through which the marking is to be done will be pre-marked by using distemper or any other pre-marking material. The desired settings for the markings (broken line, continuous lines etc.) will be made in the control panel of Automatic machine or the relevant size of screed box will be fixed to the applicator. The glass beads for super imposition on the markings will also be put into its container and settings to be adjusted at 250 grams per sqmtr. The glass beads applied to the surface of the complete stripe shall be applied by an automatic bead dispenser or by bead dispenser operating on gravity. The molten material will be allowed to pass into the screed box of the desired size (10 cms, 15 cms etc.) or adjusted in the automatic machine’s extruder unit. The screed box or the extruder unit will also be heated using the built in heaters. The machine will be driven through the pre-marked line and the screed box or extruder shutter is opened which will allow the material to flow to the surface and lay a uniform film of 2.5mm thick of thermoplastic material. Traffic Cones, Safety Jackets will be provided to divert the traffic from the main carriageway to the next lane / road to save the marking from the moving vehicular traffic. After the 30 – 60 min. of drying, road can be opened to traffic. For working on Portland Cement Concrete surface, a sealing primer from Any company shall be applied to the pavement in advance of placing of the strips to ensure proper bonding of the compound. The primer will be brush / spray machine applied @ 4-5 sqm per ltr. For marking of pedestrian crossings, directional arrows, chevrons etc. only manual applicator is used with 50 cms screed box and stencil wherever necessary. A team of well-trained staff would be executing the work strictly as per IRC-35 and MORTH specifications.

• Brand Name: DVR Coating
• Application: Metal
• Finish: Gloss/Matt
• Color: Brown
• Packaging Size: 1 Ltr
• State: Liquid
• Country of Origin: Made in India
• Is It Waterproof: Waterproof
• Grade Standard: Industrial Grade
• Packaging Type: Can
• Paint Base Type: Solvent Based
• Is it Anti Corrosive: Yes
• Application Method: Brush, Roller
• Features: Good mechanical properties, low exotherm & long pot life
• Provide Services: Yes

• Brand Name: PPCOAT PRIMER
• Application: INDUSTRIAL / FABRICATION USE
• Application: SPRAY / BRUSH
• Model Number: EPOXY BASE PRIMER

We are offering Epoxy Grey Primer. Description: a two component epoxy polyamide pigmented with durable pigments giving a matt finish. scope: a two pack epoxy high build coating with superb performance in severe marine & industrial environment. The product has excellent resistance to chemicals, solvents, fumes, splash & spillage. Can be used in various industries including refineries, fertilizers & other chemical plants. Drying time: surface temp touch dry hard dry overcoating interval minimum maximum pot life 15c 2 hours 12 hours 24 hours 10 days 12 hours 25c 50-55 min 6 hours 16 hours 6 days 6 hours 35c 30 min 4 hours 8 hours 4 days 4 hours specific gravity: 1.28 volume solids: 50 thinner clean up: pragati make epoxy thinner flash point: 30c pack size: 51020 liters application: stir base thoroughly & then mix 4 parts of base & 1 part of catalyst by volume to uniform consistency. Allow the mixture to mature for 30 minutes & stir again before application & during use. Brush roller: add up to 5% thinner if required during application. Conventional spray: add up to 15% thinner depending on conditions. Use only standard equipment at an atomizing pressure of 3.5-4.9 kgcm2. Airless spray: apply preferably without thinning. However up to 5% thinner may be added if absolutely essential depending on conditions. Use any standard equipment having pump ratio 30:1. Tip size 0.38-0.43mm.tip pressure 110-160 kgcm2 . Surface preparation: remove grease, oil & other contaminants preferably by using degreasing solvent. Blast clean to a minimum of sa2 ½ swedish std sis 05 5900. For severe corrosion, blast to sa 3 with a surface profile not exceeding 65 microns. The surface should be clean & dry before application of primer coat. Storage: up to 6 month in intact condition or sealed the containers are kept under cover in a dry place under normal temp.conditions.

• Application: Car Paint
• Color: White
• State: Liquid
• Brand Name: Plasma
• Color: Red
• Country of Origin: Made in India
• Packaging Size: 5 lit
• Coverage Area: 8-9 sq. mt / lit
• Primer Base Type: Epoxy
• Form: Solvent
• Finish: Matt
• Solid Content: 52- 55%
• Density: 1.40 kg/ lit
• Drying Time: 10 mins surface dry, Hard Dry : 24 hrs.
• Coats Required: 01
• Is It Anti Corrosive: Anti Corrosive

• Usage: Used for waterproofing and protecting of new and old roofs, terraces, podiums, planters etc.

Single component low viscous moisture cured with hgith quality polyurethane base adhesive for concrete surface and structures as a priming membrane.

• State: Paste
• Color: White
• Packaging Size: 1-20ltr
• Shelf Life: 2 Years
• Method of Application: Brush
• Quality: Superior

• Type: Epoxy Paint
• Brand Name: TriFlor
• Application: Brush
• Color: Blue, Orange, Pink, White, Green
• State: Liquid
• Finish: High Gloss
• Packaging Size: 1-5 L, 10-15 L, 5-10 L

used as topcoats in epoxy flooring. appliction areas : industrial commertial pharmasutical hotels & resturants parking areas

We offer a wide range of two pack epoxy primers, a preparatory material, which is coated on the surface that is to be painted. These primers are used for pre-coating of various materials like wood, metal etc.

Polyurethane Epoxy Floor Coating Our Range Includes Epoxy Paints, Coal Tar Epoxy, Polyurethane Coatings, Stoving Paints, Fast Drying Enamels, Etch Primer, All Types Of Primers, All Types Of Thinners AD Stoving PU Epoxy Lacquers & Peelable Lacquers Chlorinated Rubber Paints, Tailor Made Anti-Corrosive Coatings & Its Applications

• Packaging Size: 20 Litres
• Color: Water White
• Form: Liquid
• Brand: Dr Fixit
• Usage/Application: Construction
• Appearance: Very Thin Liquid Like Water
• Surface Dry Time: 10 -15 minitues

• Packaging Size: 1L
• Packaging Type: Bucket
• Type: Alkyd Primer
• Brand: Berger
• Finish Type: Matt
• Application Method: Brush
• Features: Excellent Whiteness, Resistant to chalking, High Opacity, Easy Brushability, Green Pro Certified

Indigo Paints ST Metal Primer is a value for money alkyd based metal primer used as an undercoat for ferrous metal surfaces. Surface Preparation & Application: Stir contents thoroughly. Clean the surface to be painted by removing all loose particles,grease, dirt, rust etc. Apply one coat of ST Metal primer. Allow to dry for 4-6 hours. Any undulation can be filled using Indigo Knifing Paste Filler Grey. Allow to dry. Sand the surface and apply one coat of Indigo ST Metal Primer. Allow the film to dry overnight before applying the topcoat. Advantages Good opacity Good adhesion

• Packaging Size: 20 ltr
• Packaging Type: Bucket
• Brand Name: Berger

• Application: Brush, Roller, Conventional or airless spray
• Color: Red
• Features: Non-toxicity, No side effects, Effective
• Uses: Used in various industries including refineries, fertilizers and other chemical installations coastal or inland steel structures
• Composition: Catalysed epoxy resin Zinc Phosphate
• Mixing Ratio: Base: Catalyst: 4 : I by volume
• Pot Life: 8-10 hours
• Recommended DFT: 25-35 microns per coat
• Corresponding WFT: 55e75 microns per coat
• Theoretical Spreading Rate: 13.5-19.5 Sq. Mtr.lLtr
• Drying Time: Touch: 1-2 hours, Handle: 5-6 hours
• Flash Point: Above 22 degree Celsius
• Packing: 20/4 Ltrs
• Storage Life: Up to twelve months as long as the sealed containers are kept under cover in a dry place under normal temperature conditions
• Uses: Used in various industries including refineries, fertilizers and other chemical installations coastal or inland steel structures

• Color: red
• Brand: Berger
• Form: Liquid,Powder
• Types: Bonding Primer
• Primer Base Type: Oil Based
• Application Method: Roller
• Drying Time: immidiate
•  :  

• Packaging Size: 20 ltr
• Packaging Type: Bucket
• Brand Name: Nerolac
• Color: White
• Country of Origin: Made in India
• Coverage Area: 12.07-13.93 sq.mt/ltr/coat,when applied on normal masonry surface by brushing
• Usage/Application: Exterior
• Primer Base Type: Water Based

• Type: Epoxy Paints
• Brand Name: Epoxy And Polyurethane Paints
• Application: Brush, Roller
• Color: Blue, Orange, Pink, White
• State: Liquid
• Country of Origin: India
• Finish: High Gloss
• Packaging Size: 1-5 L, 10-15 L, 15-20 L, 20-25 L, 5-10 L
• Application: Industrial use

We are offering epoxy paints. epoxy flooring can be applied over many different materials, including steel, concrete, and wood. However, concrete is the best surface for laying epoxy floors. Epoxy floor coating performance is directly affected by surface preparation. The integrity and the service life will be reduced significantly if the surface is improperly prepared. A proper surface preparation ensures epoxy coating adhesion to the substrate and prolongs the life of the epoxy coating system.