Back Back
2A Variable power supply
DC Adjustable Power Supply: This is a 24VDC 12VDC 10VDC 5VDC linear regulated adjustable power supply and consists a step down transformer. Output is adjustable by preset on the PCB.External potentiometer can be used for adjusting the output voltage. The output is almost ripple free and can drive resistive and inductive loads. The power supply do not induce any noise. This power supply is ideal for PLC,encoder,controller,sensors ,Embedded systems, proximity switches etc.The output is having short circuit and thermal overload protection. This linear power supply is very cost effective. Available in different current ratings as 3Amps2Amps.The power supply can be used as a 7AHr battery charger.
...more
Two stage voltage Sensing Relay
Voltage Sensing Relay two stage: Using this module AC or DC voltage levels can be sensed. The input voltage can be up to 2000V.If external voltage has sourcing capacity of 75 mA then the module uses the power from external sensing signal. In case the input supply has sourcing limitations then external 24VDC supply is required. There are two relays and sensing voltage of each relay can be set saperately by a preset. User can use two potential free contacts of two relays for their application. Features: â€Â¢ DIN rail mountable â€Â¢ LED indication for relay status â€Â¢ External power supplySignal supply selectable by jumper. â€Â¢ Input voltage can be ACDC of up to 2000V
...more
Solid State Relay
Number of Poles : single pole
Single Phase Heater Controller
Q-Log Controls and Systems has developed Phase Controlled PMDC drive useful for controlling speed of PMDC motor. The drive works in open loop control. Drive can be supplied as a single phase heater controller or AC light dimmer. The product is completely developed by state of the art facilities at Q-Log Controls & Systems, Pune.
...more
24DC Relay Board
Application Relay Interface Module 1 changeover DC used to interface 24DC digital outputs to contactorssolenoid valvesindications etc. Load and PLC ops secondary are galvanically isolated. Fast acting fuse is at NO point for short circuit protection. COMPONENT SPECIFICATIONS Relay: 24VDC coil,1 changeover Omron Relay socket: 1 changeover PCB soldering type Terminals: Screw type suitable for 2.5 sq. mm wires Profile and end plates: Phoenix make
...more
Redundant Power Supply Modules
Redundant module for power supply: This module enables user to make redundant power supply in a control system. The module is available in 3 varieties viz. 6Amps, 10 Amps and 25 Amps. Two power supplies are connected in parallel. Initially any one of the two works for the control system and second power supply is standby. When the working power supply fails then standby power supply starts working. Healthy indications of both power supplies are on the module.
...more
3A PMDC Drive
Q-Log Controls and Systems has developed Phase Controlled PMDC drive useful for controlling speed of PMDC motor. The drive works in open loop control. Drive can be supplied as a single phase heater controller or AC light dimmer. The product is completely developed by state of the art facilities at Q-Log Controls & Systems, Pune.
...more
PID Control Demonstration
This is a PID controller simulator and runs on soft PLC platform. The backend code is developed in IEC61131 PLC software development languages. The Codesys V2.3 software has IEC61131 PLC development environment with frontend tools. This is very usefull application for studying PID control system. After running the software you can adjust P, I, D values online to optimize controller. You can also change position set point. In auto mode if Safe Stop button is pressed then the PID controller adjusts pressure inside the chamber to equilibrium pressure, so that the weight stops at its present position. With permutations of PID values you can check working of PID controller in Overdamped state or Underdamped State or Critically damped state. Real time graph of set pressure and actual pressure can be observed.
...more
Optoisolator Board
Function of optoisolator: An opto-isolator, also called an optocoupler, photocoupler, or optical isolator, is a component that transfers electrical signals between two isolated circuits by using light. Features DIN rail mountable FourFiveSixEight optoisolators on single board LED indication for input signal Positive supply commonnegative supply common selection by jumpers 234 Outputs can be grouped to same supply by jumpers
...more
Loadcell Averaging Circuit
This unit is very useful to average the loadcell signals received from 642 loadcells. In a weighing system more than one loadcells are used for balancing purpose. In such situation the averaging circuit averages the signals connected to the unit and gives averaged mV signal. If suppose in a system four loadcells are connected. If measured individual signal of loadcells it is found to be 10.5mV, 10.6mV, 10.5mV and 10.4mV. If these loadcells are connected to the averaging circuit then the output will be 10.5mV. Excitation voltage is to be connected to the unit. There is provision of connecting 6 loadcells. Excitation voltage of each loadcell can be fine adjusted. This adjustment is to adjust output from a loadcell.
Applications : Weighing systems,Tension measurement systems, Load balancing in a mechanical system
...more
Loadcell Amplifier
This is a DIN rail mount unit. It can be field mounted near load cell. As signal is amplified and than transmitted from field, it drastically reduces chances of noise pick up. Output of the amplifier is linearly proportional to weight applied on the sensor.
Size : 45 (W) mm x 75 (H) mm x 112 (D) mm
...more
Light Dimmer
Q-Log Controls and Systems has developed Phase Controlled PMDC drive useful for controlling speed of PMDC motor. The drive works in open loop control. Drive can be supplied as a single phase heater controller or AC light dimmer. The product is completely developed by state of the art facilities at Q-Log Controls & Systems, Pune.
Size : 135x90x55 (HxWxD)
...more
HTL to TTL Signal Converters
HTL to TTL converter
TTL to HTL HTL to TTL converter 1000KHz: This is TTL to HTL or HTL to TTL converter or differential to single ended converter or Single ended to differential converter.This module receives three differential signals viz +A,-A,+B,-B,+Z,-Z signals (3-10 VDC or 10-24 VDC PP) and converts differential signal in to single ended signals A,B,Z.Pulse amplitude of output pulses is adjustable from 4.0 VDC to 24 VDC using a preset.In reverse way the module receives three signals A , B ,Z w.r.t. GND and converts the single ended signal in to differential signal (+A,-A) (+B, -B) and (+Z,-Z) ,the differential voltage is adjustable from 4.0 VDC to 24 VDC.Three point converter is for 3 signals and 2 point converter is for 2 signals. Features: . Output of type Source Sink Push Pull in single module. · Input in the range 3-10 VDC and 12-30 VDC (Peak to peak voltage) · Minimum Driving current: 1.6 mA · Supply voltage:24-30 VDC@300mA . Output pulse train voltage adjustable from 4 � 28 VDC by preset · Maximum input frequency 2000 KHz · Reduces high frequency noise and gives clear square wave
...more
Encoder Splitter Multiple Outputs
Encoder Splitter 1000KHz Multiple Outputs Multi output Encoder splitter:-This product is in modular form and has master card and slave card.Maximum four cards can be cascaded on single master card.Master Encoder splitter receives four signals from increamental encoder or simulated encoder output from servo drive and converts these signals in to two sets of encoder signals viz +A,-A,+B and -B.The output signals are optically isolated from the input signals. Slave Encoder card receives four encoder signals from master encoder card and gives two sets of of encoder signals viz +A,-A,+B and -B. Feature Input signals 3-10 or 10-30VDC 10 Encoder output sets from single encoder input Sink Source Push pull Open collector (Transistor) outputs. Supply voltage 24-30 VDC@1AmpÃ�· Output pulse voltage 51024 VDC as per customer�s requirement. Each output can drive150mA load. Din rail mountable
...more
1000 KHz Encoder Splitter
Encoder Splitter 1000KHz Technical Information Function of Encoder Splitter: Encoder splitter receives six signals from increamental encoder or simulated encoder output from servo drive and converts these signals in to two sets of encoder signals .The output signals are optically isolated from the input signals.
...more
1000 KHz Encoder Splitter
Encoder Splitter 1000KHz Technical Information Function of Encoder Splitter: Encoder splitter receives six signals from increamental encoder or simulated encoder output from servo drive and converts these signals in to two sets of encoder signals .The output signals are optically isolated from the input signals. Features: Input signals 3-10 or 10-30VDC Sink Source Push pull Open collector (Transistor) outputs. Supply voltage 24-30 VDC@1Amp Output pulse voltage 51024 VDC as per customer̢۪s requirement. Each output can drive150mA load. Din rail mountable
...more
1000KHz Single Ended Signal Converter
Function of differential to single ended signal converter: This module receives six differential signals viz +A,-A,+B,-B,+Z,-Z signals (3-10 or 10-24 VDC) and converts differential signal in to single ended signals with pulse amplitude equal to user supplied voltage anything between 30-5 VDC.Outputs are optically isolated from input encoder signals. Features: � DIN rail mountable � Three (A,B,Z) outputs module � LED indication for output signals � Reduces high frequency noise and gives clear square wave output. � Source type outputs
...more
1000KHz Differential Single Ended Signal Converter
Function of differential to single ended signal converter: This module receives six differential signals viz +A,-A,+B,-B,+Z,-Z signals (3-10 or 10-24 VDC) and converts differential signal in to single ended signals with pulse amplitude equal to user supplied voltage anything between 30-5 VDC.Outputs are optically isolated from input encoder signals.
...more
25KHz Differential Single Ended converter
Function of differential to single ended signal converter: This module receives six differential signals viz +A,-A,+B,-B,+Z,-Z signals (5-24 VDC) and converts differential signal in to single ended signals with pulse amplitude equal to user supplied voltage anything between 65-2 VDC.Outputs are optically isolated from input encoder signals. Features: · DIN rail mountable · Three (A,B,Z) outputs module or Six (A,?,B,B?, Z,Z?) outputs module · LED indication for output signals · Reduces high frequency noise and gives clear square wave · Sink type and Source type outputs
...more
DC Solid State Relay Board (Compact)
DC Solid State Relay Board: This is a opto-Transistor with optical isolation between input signal and output signal. This is to be used for switching 24V-60VDC supply by 5V-230 VDC input signal. Features DIN rail mountable, compact and easy for troubleshooting. TwoFourEight phototransistors on a single board. Sink or Source type input connectable LED indication for input signal. Ideal to drive hydraulic and pneumatic solenoid coils. Built in free wheeling diode across driving load for every individual output point
...more
5A DC Solid State Relay Board
DC Solid State Relay Board: This is a opto-Transistor with optical isolation between input signal and output signal. This is to be used for switching 5V-100VDC, 5060Hz supply by 5V-230 VDC input signal. Features DIN rail mountable EightFour DC SSRs on a single board Sink or Source input selection by jumper selection LED indication for input signal Semiconductor Fuse protection for short circuit and overcurrent Output points in two groups. Each group consists four op points
...more
DC Solid State Relay Board - 2A
DC Solid State Relay Board: This is a opto-Transistor with optical isolation between input signal and output signal.This is to be used for switching 5V-100VDC,5060Hz supply by 5V-230 VDC input signal. Features DIN rail mountable EightFour DC SSRs on a single board Sink or Source input selection by jumper selection LED indication for input signal Semiconductor Fuse protection for short circuit and overcurrent. Output points in two groups. Each group consists four op points.
...more
DC-DC Converter Custom Built
This DC-DC converter is ideally suitable for converting DC supply in to regulated DC power supply. This is very cost effective solution for battery operated vehicles. Converter is DIN rail mountable.Input voltage up to 60 Volts.The output is adjustable with presets.Output is settable from Input Voltage to (input Voltage-20V)
...more
PID Controller Simulator
Reviews & Ratings
Write a ReviewBe first to Rate
Rate This
Share your Correspondence Details to receive messages from Q- Log Controls And Systems
Post Free Ad