Safety & Pressure Relief Valves Dealers in Shivane, Pune

We are the main supplier of this product.

• Features: Flawless finish, Durable, Reasonable
• Working Pressure: 20 bar
• Coil Voltage: 12 V DC
• Body: Brass Forged ( BSS 218)

• Application: Misting System
• Size: 1/8" to 1/4" BSP
• Pressure: 0 bar to 100 bar

• Material: Stainless Steel
• Valve Size: 1.5 inch
• Operating Pressure: Up to 3,700 psig
• Process Fluid: Liquid
• Body Style: Angled and Inline
• Set Pressure: 50 psi

• Flow Rate: up to 6000 SCMH
• Inlet Pressure: up to 49 kg/cm2
• Outlet Pressure: 0.03 to 26 kg/cm2
• End Connections: 1” NB to 4” NB Flanged as per ANSI 150/300.

PRS/Gas Trains Design Features: PRS/Gas trains are consisting of, Ball valves: to isolate the system from main supply or to isolate the either side of PRS. Filtration unit: A filter protects rest of the system from any debris or dust that may carried with gas stream. Debris may for example consist of parts accidently left in the pipe during construction. It could also result from swarf from drilling holes & taps or welding & sand from construction or fine iron oxide dust. Slam shut off Valve: Slam shut off valves is installed after Filter & before pressure regulator. Slam shut off valve close the supply of gas when a downstream pressure exceeds a pre-determined limit. Pressure regulator: Pressure regulator maintain downstream pressure at certain quantity of gas , irrespective of variation in upstream pressure from maximum to minimum limit. Spring loaded or Pilot operated pressure regulators are used. Relief valves: Creep relief Valve: A slight weeping of pressure regulator/ increase in downstream due to rise in downstream surrounding temperature result in increasing the downstream pressure to dangerous level, such creep pressure is blown off through creep relief valve. Safety Relief Valve: The safety relief valve set at higher pressure than slam shut off valve so that the safety relief valve will operate when slam shut off valve fails to operate.

The Samson make Type 41-23 self-operated universal pressure reducing regulator is a standard size regulator (1/2" - 4") designed to work in all general industrial applications. A pressure reducing valve is used for controlling the downstream pressure (p2) to an adjusted set point. The design of a pressure reducing regulator valve is to close when the downstream pressure rises above a set value.These valves are self-operated in that the downstream pressure being controlled is tapped downstream of the Pressure Reducing Valve and transmitted via a control line to the operating diaphragm of the Type 41-23 where it is converted into a positioning force.   Special features of Pressure Reducing Valve: Low-maintenance proportional regulators requiring no auxiliary energy Frictionless plug stem seal with stainless steel bellows Control line kit available for tapping the pressure directly at the valve body Wide set point range and convenient set point adjustment using a nut Exchangeable set point springs and actuator Spring-loaded, single-seated Pressure Reducing Valve with upstream and down stream pressure balancing by a stainless steel bellows Soft-seated plug for high shut-off requirements Standard low-noise plug Special version with flow dividerSt I or St III (NPS 2½ to 4/DN 65 to 100) for further noise level reduction All wetted parts free of non-ferrous metal   Application of Pressure Reducing Valve: Pressure regulators for set points from 0.75 to 400 psi (0.05 to 28 bar) Valves in NPS ½ to 4 (DN 15 to 100) Pressure rating Class 125 to 300 (PN 16 to 40) Suitable for water,gases, and vapors up to 660 °F (350 °C)

Pressure Regulating Valve is ideal for application where downstream pressure requirement is constant. They are used in various process lines, Stream, Nitrogen Blanketing systems, Fuel control systems and LPG distribution systems. Rutcon PRV provides a reliable and economic solution for Pressure Regulation. Sizes : ½� to 8� (15mm to 200mm) Higher sizes available on request Ratings : ANSI B 16.5 150# and 300# other standards available on request. Application : Used in fertilizers, chemical, and pharmaceutical plant etc. and other process industries commonly used for burner fuel oil pressure regulation, nitrogen blanketing system, etc. Design & Performance Features Used for long trouble free serviceValve Disc is reversible and can be changed quickly for renewed lifeSelf actuating type, does not require any auxiliary energyRange of body & diaphragm material combinations to meet majority of requirementsPressure balanced design, any fluctuations in the inlet pressures has negligible effect on the regulated pressure

Brass (IS 319) - Standard (AL MS S.S. also available). Finish Nickel plated-Standard. (TinCadmiumChrome also available) Threads BSC - Standard (In PGMetricNPTBSP-also available) Ref. Standard IS 2148 - 1981 CMRI Certificate No CMRITCPH638, Application Flamepoof used in flammable gas vapor area (Gas l, llA and llB)

steam pressure reducing stations, Steam Boilers

High Pressure CNG Solenoid Valves, lpg filters, LPG Filter Solenoid Valves

Fittings, Bolts, Nuts, Studs, Fasteners, Pipes, tubes, Flanges

Multifunction Valves Thirty Degree Multifunction Valve, CNG Kit For Car