V Blocks Dealers in Pune

MRM – 475, 475 H, 575, 575H, 676, 676H, 856, 856H, 876, 876H, 976, 976H These Magnetic –Vee blocks are invaluable and versatile in tool – making and inspection, in quality control and tool – room. Due to their extremely high magnetic power they can be used for drilling and grinding (both wet and dry) and even for light milling work. The  - Blocks have a total of three magnetic surfaces. Top and bottom each with 90-degree v – angle and end surface opposite from switch. All three magnetic surfaces as well as the two sides are carefully ground. Their accuracy for flatness, parallelism and square ness is within 0.005 mm or 0.0002 inches for all work, which requires accurate positioning. When turned ‘ON ‘ all three magnetic surfaces are activated simultaneously. The permanent magnet holds the work firmly in the V and the block holds itself firmly on a ferrous surface. Coolants or other fluids cannot damage the magnetic system, being shielded from penetration of moisture.

• Brand Name: Ultra
• Magnet Grade: N35, N38, N40, N42
• Accuracy: 0.005 mm upto 150 mmL and 0.010 mm for 200 mmL
• Hardness of V face: 58Hr

The "Crystal" Roller Bearing 'v' Block are accurately assemble and precision ground on the bottom faces. Four high precision ball bearing on the top. Thus, providing self aligning wearing hard accurate support which will not damage even the most delicate work piece. "Crystal" Roller Bearing 'v' Blocks are very useful in tool room, machine shop, assembly, inspection for checking and marking odd shapes job , round job, crank-shafts etc. Due to the Roller bearing the work pieces are not damaged. It has equal bearing properties. Bearing become excessively without causing inaccuracy can be replaced easily. Due to its design feature, the Roller Bearing 'v' Block are supplied in matched pairs.

• Material: Cast Iron
• Brand Name: Micro Flat Datums
• Color: Green and Silver
• Shape: V
• Size: 80 x 63 x 80 mm
• Clamping Range: 7-80 mm

MagTech Magnetic ‘V’ block’ is basically a clamping device. Hence, it is used in Standard Room Tool Room and Shop Floor also for Drilling, Grinding Light Milling operations. The 'V’ Block has a total three magnetic surfaces. Top, bottom with 90 degree angle and end surface opposite from switch. Magnetic surfaces are activated by mechanical ON-OFF switch. All three magnetic surfaces and the two sides are carefully ground. The main ‘V’ angle and bottom surface are provided with hardened steel plates, that ensures extra wear resistance. The accuracy of flatness and parallelism and squareness is within 5 microns for 4” & 6”; as well as 10 microns for 8” ‘V’ blocks. The following photograph can explain the product and its utilization briefly. 'V’ Blocks are required for Quality Control, Tool Room and Standard Room. Our Magnetic 'V’ Blocks have high magnetic pull, hence they can be used for drilling and grinding (both wet and dry) and even for light milling work. When turned "ON" all three magnetic surfaces are activated simultaneously. The permanent magnet holds the work firmly in the 'V’ and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease even after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.  

V Blocks are designed to hold round parts. They fit into the holes of the FIXTO Table and other clamping accessories Features : • Modular Type  

• Features: Easy usage, Non-corrosive, Low maintenance, Simple design, Enhanced durability,

The Roller Bearing 'V' Blocks are accurately assemble and precision ground on the bottom taces. Four high precision ball bearing on the top. Thus, providing self aligning wearing hard accurate supports which will not damage even the most delicate work piece. "Crystal" Roller Bearing 'V' Blocks are very useful in tool room, machine shop, assembly, inspeciton, for checking and marking odd shapes jobs, crank-shafts etc.

• Material: Alloy Steel
• Magnet Grade: N52, N40, N42, N38, N35

  Non Magnetic 'V' Block (With Clamp)Non-Magnetic 'V' Block is Basically Used for Clamping of Non-Magnetic Material. The 'V' Block has Two 'V' Angles of Different Sizes to Inspect The Jobs of Varying Dimension. Material Used For Manufacturing of This Product is Alloy Steel. It Prvides Accuracy Within 3 Micton. These Blocks Are Hardened And Ground Hardness 60 to 63 HRC. These 'V' Blocks Are Mainly Used in Tool Room And Standard Room Size (In mm) L x W x H 25 x 20 x 25 40 x 40 x 50 80 x 63 x 63 100 x 80 x 80 50 x 50 x 50 63 x 50 x 50 63 x 100 x 100 70 x 140 x 140

v block, Air Ventilator, Roofing Sheets, Magnetic V Block, exhaust systems

v block, snap, Calibration, Magnet, chuck, repair, tool, Jig

v block, glass edge polishing machine, Pneumatic Grease Pump

Magentic V Block, air angle grinder, pcd insert, Collet Stud

Precision V Block, Hard Jaws for Hydraulic Power Chucks, Double Clamp Vise

Magnetic V Blocks, pushpull gauge, Torque Wrench