Windris India Private Limited Sahakar Nagar, Pune, Maharashtra

  • Third Rail Shoegearsgraphs

    Third Rail Shoegearsgraphs

    Request for Price

    We are specialised in customised innovative solutions in the field of third rail shoegears for suburban rail, metros and rapid transit rail.Thanks to its large cross-section, the third rail can transmit high current densities. It is always used when an overhead wire for roof-mounted pantographs cannot or should not be installed. The maximum vehicle speed with third rail shoegears is approximately 120 km/h. Deployment and retraction can take place manually or by remote control, i.e. through mechanical or pneumatic systems. The contact to the conductor rail can be made from the top or the bottom or even from the side.Our third rail shoegears are in everyday use in local rail networks of the big cities regions and metropolitan areas. STEMMANN-TECHNIK develops a perfect system for every vehicle type, for every vehicle model and railway network. We realise individual customizations for any application professionally and in time.

    ...more
    Get Best Price
  • Third-Rail-Shoegears

    Third-Rail-Shoegears

    Request for Price

    We are specialised in customised innovative solutions in the field of third rail shoegears for suburban rail, metros and rapid transit rail. Thanks to its large cross-section, the third rail can transmit high current densities. It is always used when an overhead wire for roof-mounted pantographs cannot or should not be installed. The maximum vehicle speed with third rail shoegears is approximately 120 kmh. Deployment and retraction can take place manually or by remote control, i.e. through mechanical or pneumatic systems. The contact to the conductor rail can be made from the top or the bottom or even from the side. Our third rail shoegears are in everyday use in local rail networks of the big cities regions and metropolitan areas. STEMMANN-TECHNIK develops a perfect system for every vehicle type, for every vehicle model and railway network. We realise individual customizations for any application professionally and in time.

    ...more
    Get Best Price
  • Stinger Systems

    Stinger Systems

    Request for Price

    Stinger systems serve to supply energy to parked vehicles in the maintenance area, e.g. for charging the battery or other maintenance work, which has to be carried out while the vehicle is electrified. Furthermore, with our Stinger systems, it is possible to move the vehicles within the depot or maintenance facility from a control panel. The connection terminals of our third rail shoegears can be used as Stinger terminals by installing a contact spike. According to customer requirements, we manufacture and assemble complete systems, including conductor lines, plug and cable connections, controller devices and contact spikes on the railway wagon.

    ...more
    Get Best Price
  • Slipring Assemblies

    Slipring Assemblies

    Request for Price

    Slipring assemblies for energy- and data transfer are being used for all products which do not allow any stationary current supply due to their rotary movement. Thus, the applications range from current transmission at slowly moving round reamers in purification plants to explosion-proof slipring assemblies with media lead-through for oil production vessels.

    ...more
    Get Best Price
  • Slip Rings Assemblies

    Slip Rings Assemblies

    Request for Price

    Slipring assemblies for energy- and data transfer are being used for all products which do not allow any stationary current supply due to their rotary movement. Thus, the applications range from current transmission at slowly moving round reamers in purification plants to explosion-proof slipring assemblies with media lead-through for oil production vessels.

    ...more
    Get Best Price
  • slip ring assemblies

    slip ring assemblies

    Request for Price

    Slipring assemblies for energy- and data transfer are being used for all products which do not allow any stationary current supply due to their rotary movement. Thus, the applications range from current transmission at slowly moving round reamers in purification plants to explosion-proof slipring assemblies with media lead-through for oil production vessels. The slip ring assembly, contact blocks and power transmissions for data or signaling can be configured and customized for every requirement. We can draw on a wide range of standardized series and advanced technologies to achieve the optimum technical and economical solution for each customer. Even for complex requirements and extreme operating conditions.

    ...more
    Get Best Price
  • Slip Rings

    Slip Rings

    Request for Price

    Slipring assemblies for energy- and data transfer are being used for all products which do not allow any stationary current supply due to their rotary movement. Thus, the applications range from current transmission at slowly moving round reamers in purification plants to explosion-proof slipring assemblies with media lead-through for oil production vessels.

    ...more
    Get Best Price
  • RTG Electrification Systems

    RTG Electrification Systems

    Request for Price

    The RTGs equipped with a diesel-electric-drive are used in harbours all over the world. By means of these RTGs trucks and so-called “prime movers” are loaded resp. unloaded with the containers of the container ships. Continuously increasing fuel costs, the required time for refuelling oft he cranes, increased maintenance costs for the diesel-electric-drives with the corresponding downtimes as well as tightened environmental regulations led tot he requirements of the crane manufacturers and port operators to as far as possible replace the standard drive by a flexible power transmission. STEMMANN-TECHNIK now has met this demand also by the successful retrofitting of RTGs by means of conductor lines. The advantages of the retrofitting are: Enormous reduction of the amount of diesel-fuel needed. Contrary to the permanently operated diesel-motor, only the actually required amount of energy is used with the external energy supply. Reduction of time and costs due to the shorter maintenance intervals of the diesel-electric-drive. Reduction of costs and work by reduction of the stops for refuelling. Significantly less emissions by the lesser use of the combustion engine and thus better environmental conditions at the site. Depending on the customer’s requirements and in cooperation with the operators at the site STEMMANN-TECHNIKwill find individual possible solutions to retrofit the RTGs from diesel-electric-drives to electrical power supplies by means of conductor lines or motor cable reels.

    ...more
    Get Best Price
  • Roof-mounted Pantographs

    Roof-mounted Pantographs

    Request for Price

    roof-mounted pantographs for tramways, trains, special vehicles, suburban railways, metros, traction units (emus) and locomotives are developed for different overhead line-systems and speeds, whereas the raising to and lowering from the overhead line is realised by an electrical or a pneumatic drive acc. to customer’s requests. the continuous contact force to the overhead line at higher speeds is realised either by mechanical aero foils or by an especially developed electro-pneumatic control. if requested an emergency dropping device is quoted which lowers the pantograph as quickly as possible at collisions with the overhead line.

    ...more
    Get Best Price
  • Onshore Power Supply for Cruise Ships

    Onshore Power Supply for Cruise Ships

    Request for Price

    The market for ship cruises is continuously growing over the past years. During the last 10 years the number of passengers only in Germany has tripled and currently this trend does not seem to end soon. The frequency of calls at the ports world-wide is constantly rising. As a logical consequence of these growths the problem of exhaust emissions in the ports is increasing. At an average a cruise ship is at the pier 40 % of its operating time. During this time the onboard systems need to be supplied with power. This usually is produced by the ship’s own diesel generator sets.

    ...more
    Get Best Price
  • Onshore Power Supply

    Onshore Power Supply

    Request for Price

    The emissions caused in the port area are a growing problem due to the increasing capacities of the ports. For keeping the vessel functional in the quay area of a port normally the required power is produced by means of auxiliary diesel engines and generators while the main engine is switched off. In the future, a power supply by means of onshore power supply units will replace the diesel-powered vessel generators to a large extent. The implementation of emission limit values and environmental specifications in general additionally expedite this development. We offer systems and system components for feeding onshore power into the onboard power grid and thus contribute to reducing the emissions of air pollutants, noise and carbon dioxide in the port area.

    ...more
    Get Best Price
  • High Power Charger

    High Power Charger

    Request for Price

    Increasingly strict regulations to reduce pollution in the cities lead to a rapid change of the infrastructure and public transportation network to electric mobility. These are, for example, charging stations for cars or electric bus terminals. Electric busses ensure sustainable urban mobility. The retrofitting of bus routes solely driving with electric buses assumes a rapid development. Solutions are, for example, implemented together with local utility companies by rapid charging stations HPC (High Power Charger). Our charging pantograph is a key component of these charging stations.

    ...more
    Get Best Price
  • Frost Ground Contacts

    Frost Ground Contacts

    Request for Price

    The mechanical structure of our frost® ground contacts fulfils the applicable national and international standards and directives. The material pairings are continually optimized. In the construction or in the direction of working of the carbon brushes, a distinction is made between axial and radial operation contact systems. In the area of standard applications, the traditional round-brush constructions have been replaced by multi-brush constructions. The reasons for this are the higher possible current transmission and the somewhat simpler construction of the contacts. We further developed the successful principle of the multi-brush contacts and derived the successful frost® pressure system from it.

    ...more
    Get Best Price
  • festoon systems

    festoon systems

    Request for Price

    Cable Festoon Systems are used for reliably transporting power supply lines. Our Cable Festoon Systems take flexible energy- and power supply lines to exactly where they are needed, also over longer distances. Power lines, data lines or supply tubes with water, compressed air, etc. can be transported over a pre-defined distance, if necessary several times over in one system. Depending on the location, C-rails (profiled guide rails), iron girders or tension cords can be used as track for the trolleys.

    Capacity : 1000 kg.

    ...more
    Get Best Price
  • ePower Charging System for Electric Ferry

    ePower Charging System for Electric Ferry

    Request for Price

    Operators of short distance eletric ferries choose our charging system to save fuel and reduce CO2 pollution. The closed tower design protects the system components against external influences and fits into the mooring area. As soon as the ferry approaches the rolling gates of the pantograph tower (country side) and the housing (ship side) open automatically. Parallel to the docking of the ferry the loading station is activated by means of an onboard remote control. As soon as the ferry reaches its docking position the charging pantograph connects during seven seconds to the onboard contact bars and the loading of the battery starts. The charging system is able to compensate the tidal range and any movement of the ferry.

    ...more
    Get Best Price
  • crane electrification systems

    crane electrification systems

    Request for Price

    The RTGs equipped with a diesel-electric-drive are used in harbours all over the world. By means of these RTGs trucks and so-called “prime movers” are loaded resp. unloaded with the containers of the container ships. Continuously increasing fuel costs, the required time for refuelling oft he cranes, increased maintenance costs for the diesel-electric-drives with the corresponding downtimes as well as tightened environmental regulations led tot he requirements of the crane manufacturers and port operators to as far as possible replace the standard drive by a flexible power transmission.

    ...more
    Get Best Price
  • Conductor Lines

    Conductor Lines

    Request for Price

    Optimal power supply and uninterrupted data communication are the pillars of modern production.STEMMANN-TECHNIK conductor lines guarantee both, effectively and safely.Efficient work processes are often only made possible by flexibly connected current collectors /data adapters along the lines. Using solid components and sophisticated system technology, we ensure the right power is available at all times – precisely where it is needed.Data connections for computerized processes are permanently stable and remain uninterrupted. Our conductor line systems also increase safety for people and the environment. Particularly when manually transporting power- and data lines within the work area is obstructive or even hazardous.All conductor lines are planned by us as complete systems. We carry out the projects on site, including suspension, control cabinets and all other necessary components – even in underground conductor line channels if necessary. The design and quality of our conductor line systems guarantee easy assembly and low maintenance operation.

    ...more
    Get Best Price
  • Charging REEL

    Charging REEL

    Request for Price

    Designed for ceiling, wall and underfloor assemblies Perfect adaptation to your e-fleet Professional design ensures reliable and durable operation Individual cable routing and plug supply systems

    Outer Diameter : 430 mm

    ...more
    Get Best Price
  • Charging PANTO bus

    Charging PANTO bus

    Request for Price

    Increasingly strict regulations to reduce pollution in the cities lead to a rapid change of the infrastructure and public transportation network to electric mobility. These are, for example, charging stations for cars or electric bus terminals. Electric busses ensure sustainable urban mobility. The retrofitting of bus routes solely driving with electric buses assumes a rapid development. Solutions are, for example, implemented together with local utility companies by rapid charging stations HPC (High Power Charger). Our charging pantograph is a key component of these charging stations.

    Type : Charging Pantograph

    ...more
    Get Best Price
  • Cable Reels

    Cable Reels

    Request for Price

    motor- and spring-driven cable reels are designed for the power supply to movable machines. The motor- and spring-driven cable reels are manufactured in accordance with the travel distances and the power of the movable machines. Regarding the version of the cable reel it is differentiated between cylindrical and spiral version. Which one of these versions is chosen depends on the customer’s resp. Design-requirements.special designs and the required accessories are innovatively produced by stemmann-technikcorresponding to the customer’s requests.

    ...more
    Get Best Price
  • Cable Festooning Systems

    Cable Festooning Systems

    Request for Price

    Cable Festoon Systems are used for reliably transporting power supply lines.Our Cable Festoon Systems take flexible energy- and power supply lines to exactly where they are needed, also over longer distances.Power lines, data lines or supply tubes with water, compressed air, etc. can be transported over a pre-defined distance, if necessary several times over in one system.Depending on the location, C-rails (profiled guide rails), iron girders or tension cords can be used as track for the trolleys.The Cable Festoon Systems are suitable both for indoor and outdoor areas. They are optimized for the specific purpose down to the finest detail.An extensive range of accessories, including special running wheels, fastening materials or materials for buffering the vehicles completes our product range. All components are solidly built and easy to assemble.We build lightweight or heavy-duty Cable Festoon Systems (plastic or steel) with running wheels for C-rails, T-beams or tension cords. The choice of system depends on the respective site location, the type of cables to be transported and their total weight.We cater to industrial workplaces, workshops and assembly halls as well as the complex requirements of large port cranes and transport systems.

    ...more
    Get Best Price
  • Frost Ground Contacts

    Frost Ground Contacts

    Request for Price

    Get Best Price

Be first to Rate

Rate This

Select the service for which you are writing review for this business

How would you rate the business?

What would you like other to know about this business, based on your experience?

Minimum 20 characters!

About the Company

  • Primary Business Retailer
  • Secondary Business Type Manufacturer / Exporters / Wholesale Suppliers

Opening Hours

  • SUN : Closed
  • MON : 9:30 AM - 6:30 PM
  • TUE : 9:30 AM - 6:30 PM
  • WED : 9:30 AM - 6:30 PM
  • THU : 9:30 AM - 6:30 PM
  • FRI : 9:30 AM - 6:30 PM
  • SAT : 9:30 AM - 6:30 PM
STEMMANN-TECHNIK is one of the world’s leading manufacturers of components and systems for energy and data transfer in industrial and traffic engineering.
Drawing on the expertise of more than 100 years of engineering and mission-oriented research, we manufacture quality products in demand worldwide and constructing innovative special solutions made to measure.
A key to success is our high quality understanding in all areas of the company. This starts with a customer-oriented consulting to a sustainable service.
The quality of the products and services of STEMMANN-TECHNIK aims to fully meet the wants, needs and expectations from our customers.
Every project and every application we design to the smallest detail under performance aspects and economic aspects.
We ensure high quality by adhering to international standards and guidelines.
The implementation of the quality management system is carried out according to standardized methods in conjunction with flexible structures for modeling and documentation of all production and business processes.
STEMMANN-TECHNIK company was founded in Luxembourg in 1912 by engineer August Stemmann. At that time, we were already involved with producing power supplies for cranes at steel and smelting works as well as for other mobile machines.
Slip ring assemblies for rotating machines and photograph systems for railway vehicles were added later on.
Since 2014 we belong to the Wabtec Corporation, a global provider of technologies, products and services in the field of railway and industrial engineering.
Read More »

Contact Information

Windris India Private Limited

  • Sunil Kuram Bhatti
  • No. 76-81/44, Renuka Bungalow, Omkareshwar Co-Operative Housing Society, Sahakar Nagar North, Pune, Maharashtra

Find Popular Slip Ring Dealers in Pune

top