Wire Making Machines Dealers in Kothrud, Pune

• Voltage: 220V
• Automatic Grade: Automatic
• Brand Name: Crimpone
• Warranty: 1 Years
• Model: C1-25SE
• Series: E Series

Servomotor driven ball screw mechanism gives highest accuracy, repeatability and speed for crimping process. C1-25se's side feeding channel is perfect for odd shaped parts. Crimpone e-serie crimping machines are fully electric, powered by servomotor driven revolutionary ball screw mechanism that gives you highest accuracy, repeatability and speed. Without oil.   No oil means no leaking problems, no hustle with oil change and no filtration problems. Just pure power, accuracy and speed.   Features Capacity to Work 24x7 for Continuous Production Eco-Friendly - No-Pollution due to Oil Wastage Zero Maintenance - Breakdown Free Machine Pressure Monitoring - Precise and Repeatable Cost Effectiveness - Great Savings on net Operating Costs Sturdy Machine - Less Effects of Surroundings on Machine Life and Performance Capacity to Stand Against any Extreme Environmental Condition Unmatched Crimping Repeatability upto

• Capacity: 300 kg.

The CO2 welding wire is available on a spool of almost 300 kg. The wire is wound on smaller spools with accurate length measurement & weight measurement. The winding is done in layer form. The bigger spool is driven by servo drive & motor. The wire is let off by the big spool & is pulled by a servomotor on smaller spool. The wire length is measured by encoder on a measuring wheel. The operator enters wire diameter, the density of material & the required weight of smaller spools. The weight measurement is done indirectly by measuring length. The wire is guided by a linear axis so as to form a uniform layer with an angle entered by operator.

Impulse Welding is an ultra modern way of metal joining, which replaces many other techniques such as riveting, soldering or conventional a welding. The actual welding takes only a few Milliseconds (Tentatively 5 to 8 mSec) so only the very welding zone is heated up while neighboring zones remain practically cold. There is no distortion, tarnishing, discoloring or annealing of metal around the welding zone. Welding time is so short that sufficient melting heat is produced in the welding zone before heat dissipation starts, unavoidable with longer welding times. This also means that the total amount of heat applied is small as possible as – hardly higher than necessary for the weld itself. The welded parts stay practically at room temperature. The high currents from Impulse Welders make this method applicable even for metals of high electrical and thermal conductivity such as copper, silver, gold and even platinum. With Impulse Welding machines, electrode cooling is not required even at very high production rates. Electronically stabilized charging with proper feedback keeps the voltage across the capacitor absolutely constant and gives constant welding energy even at power line variations giving highly reproducible welding results. In the Impulse Welding the required welding energy is stored in a CAPACITOR BANK, being charged during the intervals between welds. As the charging of the capacitors takes place at quite slow rate, there is a great saving on power supply requirements as compared to conventional ac welding machines. There is no sudden heavy burden on the mains supply creating problems to other machines and environment. Production speeds are limited only by the time required for job feeding mechanism, which is sufficient time for recharging the required capacitor banks, because of negligible short welding times. Welding performance is dependent on Welding Energy and Applied Pressure. With Capacitor Discharge welding machine, the Energy is maintained constant and the pneumatic Weld Head maintains the required pressure. A special pneumatic Weld Head is provided for welding very fine wires. This special unit applies very low pressure for fine wire welding, which is adjusted for different type of jobs, depending upon the size, type conductivity and type of the material to be welded. A Simple Manual Weld Held can also be provided for non critical applications.Potential Free contact is provided for inert gas purging (both post & past time) operation. Separate Manual operation is possible for trials and testing.   ADVANTAGES :  • Welding without oxidization, distortion annealing or discoloration• Welding close to heat sensitive parts.• Good welding results with metals of high electrical and thermal    conductivity.• Welding of parts of different cross sections and materials.• Very high productivity• High repetitive rate possible• Long Electrode life, with no cooling requirements• Welding of both Ferrous and nonferrous metals.• Welding not affected by Power Line fluctuations• Welded parts can be of less tolerance and may not need cleaning.• Power supply connection just 5 Amps     Welding of Fine Wires is another task. The Welding Energy as well as pressure during weld is very critical for welding. We have developed a special pneumatic fixture with adjustable differential pressure, so as to take care of the above requirements. With this fixture and the machine we can weld 40-44 SWG Pt to PtPtRh15% or PtPtRh13% wires, without the requirement of any skilled personnel. The production cycle can be about 6 seconds each.

Ceramic wire drawing cones, rings & guides are commonly used for drawing and production of non-ferrous wires in the wire and cable industries. As Zirconia/Alumina exhibit high toughness, high hardness, good abrasion and corrosion resistance, this makes them ideal choice material for wire drawing applications.Techno Cera wire drawing cones, rings & guides are manufactured in various shapes and sizes & ground to precise dimensions as per customer requirements 

• Brand Name: NRE
• Voltage: AC380V
• Features: Excellent repeatability
• Capacity: 0.1 kg to 50 t
• Operating Temprature: 50 Deg C
• Power: 400W
• Storage Temperature Range: -10 Deg C To 70 Deg C
• Accuracy: 0.1%

• Brand Name: UMI
• Color: Blue, white
• Country of Origin: India
• Model Number: UNIST
• Certification: ISO
• Function: Computerized
• Blue: white

We have created a niche as the most eminent spring tester manufacturer and exporter from india. We provide a wide range of spring testing machine which is incorporated from the high grade quality raw material. Our automatic spring testing machine encompasses both brilliant performance and excellent quality. Our spring testing machine saves the precious time of users and gives result quickly. We are also manufacturers of Complete Lab Testing Equipments

• Features: High strength, robust construction, Excellent repeatability

• Voltage: 220V/1PH/50HZ
• Material: Metal & Steel
• Type: Spiral Wire Forming Machine
• Weight: 100-200KG
• Condition: New
• Power: 60/50HZ
• Computerized: Yes

We are the main supplier of this product.

wire drawing parts, advanced ceramics, Ceramics, ceramic choke beans

precision layer winding machines, automatic packing lines

CNC Coil Winding Machines, cnc laser welding machine, Digital Counters

edm wire cut machine

Ceramic, Tiles, adhesiv mosaic, glazed, galicha