Balaji Group of Industries Kotharia, Rajkot, Gujarat

Types: BSP | NPT Material M.S. | SS-304 | SS316

Features: Investment Casting SS 140 | 304 | 316 Availabe Sizes: 1/2 | 3/4 | 1 TYPICAL APPLICATIONS   DRIP, TRACER: The FS600 Thermodynamic stream trap is commonly used as a drip trap on steam mains and steam supply lines. Supplied with integral Strainer and these traps can be used on tracing applications; however, thermostatic traps are normally recommended for this service. Ideal for outdoor application that Are subject to freezing and for superheated steam conditions   HOW IT WORKS The thermodynamic trap has cyclic on-off operation with a disc that is pushed open by incoming condensate and closes lightly when steam tries to escape.   FEATURE   Integral strainer protect trap from contamination   Hi pressure applications up to 600 PSIG   Hardened stainless steel seat and disc for extended service life even at high pressure   Singltrap will operate over the entire pressure range of 3.5-600 PSIG [Not recommended for use below 10 PSI]   Suitable for superheated steam   Freeze proof when trap is piped in a vertical orientation for complete drainage of condensate   Tree-hole balanced discharge extends life of the seat area   Trap will function in any orientation (horizontal preferred)   SAMPLE SPECIFICATION The steam trap shall be all stainless steel thermodynamic type with hardened integral seat and disc with integral strainer.   INSTALLATION Trap can be installed in any position; however horizontal is preferred. Installation should include isolation valves. Do not weld or damage can occur to the seat area.   MAINTENANCE If trap fails, close isolation valves and remove cap. clean disc and seating surfaces and replace cap and disc with grove side toward seat.

Salient Features of Spring loaded Disc Type Non Return Valve: • Investment Casting Body Construction • Compact & Rugged Design • Stronger, liter and Smaller than Conventional Swing Check    valve, Hence less Expensive to install and maintain • Single Disc Type • Spring Loaded Disc to Prevent Reverse Flow in Pipe Line • Easy To Installation Between Two Pipe Flanges • Metal To Metal or Soft Seat Option • Maintenance Free Design • Zero leakage (in Soft Seat) • Full Port Opening • Less Pressure Drop • wafer, Flangeless, Sandwich Type • Shorter Length, Required Minimum Space • Offer any 3rd Party or Client Inspection pring Loaded Wafer Disc Check Valve: Flowset Spring Loaded Disc Check Valve - Non Return valve feature a wafer type, compact and rugged design cast carbon steel (ASTM A216 GR.WCB) or stainless steel (ASTM A 351 GR.CF8/CF8M CF3/CF3M/SS304/SS316/SS304L/SS316L) construction and are suitable for any process liquid, air, gas, steam etc. the signal disk check valve (water type signal disk check valve)consists of four main components: the body, disc, a star guide and a spring. The disk check valve are opened by the pressure of fluid and closed through compression spring as soon as flow stops thus preventing reverse flow. The design of wafer design, sandwich Type, flangeless single disk spring loaded check valves allows them to be installed between any flanges of different standard and in any position; including vertical pipelines where the fluid flows downwards. wafer type spring loaded disk check valves is also available with zero leakage by the use of soft seat . flowset valves & Automation has cover disk check valves up to 4”( DN100)size and pressure rating up to PN40.

Features: Black Steam Fitting Availabe Sizes: 6MM | 8MM | 15MM | 20MM 25MM | 32MM | 40MM | 50MM

technical specification body:- bar strok ss 202 / 304 / 316 seals:- ptfe teplon pressure:- 350 kg-cm [5000 psi] temperature range:- 200 °c leakage:- bubble titght endes:- screwed [ m ] / [ f ] bsp [ npt on request] media:- air / water /oil /gas available sizes 1/4 | 3/8 | 1/2 .

Investment Casting Ball Valve | Forging Ball Valve | Flanged Ball Valve | C.I Casting Ball Valve Available Sizes 15MM | 20MM 25MM | 32MM 40MM | 50MM Material / Pressure CF8M | CF8 Pressure---2000 PSI

All types of industrial valves 

Material : Carbon Steeel

Usage : Oil Fitting

Brand Name : Flowset

Valve Size : 1/4 to 300 mm

Color : White

Number Of Way : 2way

Type : S/e

Mounting Type : Bonnet

Packaging Type : Carton

Weight : 20kg

Country of Origin : India

Features Reduced Or Full Port Compact Outside Screw & Yoke Spiral Wound Gasket Of Stainless Steel Bolted Bonnet or Welted Bonnet Socket Weld Or Threaded Ends Integral Hardfaced Seat Applicable Stabdards Basic Design, BS 5352 & Ansi B16.34 Socket-Weld (S.W) Ansi B16.11 Threaded End (S.E) Ansi B1.20.1 Valve Test And Inspect :API 598 Standard Material: A105N, LF2, F5, F11, F22, F304, F304L, F316, F316L.

Valve Size : 1/2inch

Features Reduced Or Full Port Compact Outside Screw & Yoke Spiral Wound Gasket Of Stainless Steel Bolted Bonnet or Welded Bonnet Socket Weld Or Threaded Ends Replaceable Hardfaced Seats Applicable Stabdards Basic Design, BS 5352 & Ansi B16.34 Socket-Weld (S.W) Ansi B16.11 Threaded End (S.E) Ansi B1.20.1 Valve Test And Inspect :API 598 Standard Material: A105N, LF2, F5, F11, F22, F304, F304L, F316, F316L.

Investment Casting Ball Valve | Forging Ball Valve | Flanged Ball Valve | C.I Casting Ball Valve Features Forging A105 800# Smooth Oprating PTFE SS Ball SS Pin Availabe Sizes 15MM | 20MM | 25MM 40MM | 50MM

forge elbow is first class finis and soketweld and screwed menufectured by balaji group of industris "FLOWSET"

Type : socketweld and screwed

Brand Name : "FLOWSET"

Material : mild steel

Shape : 45 digree

Technics : presure

Connection : socketweld and screwed

Head Code : 0.5

We are offering forge globe valve. Features : reduced or full port compact outside screw & yoke spiral wound gasket of stainless steel bolted bonnet or welted bonnet socket weld or threaded ends integral hardfaced seat applicable stabdards : basic design, bs 5352 & ansi b16.34 socket-weld (s.w) ansi b16.11 threaded end (s.e) ansi b1.20.1 valve test and inspect :api 598 standard material: a105n, lf2, f5, f11, f22, f304, f304l, f316, f316l.

We are offering forged gate valve, features : reduced or full port compact outside screw & yoke spiral wound gasket of stainless steel bolted bonnet or welded bonnet socket weld or threaded ends replaceable hardfaced seats applicable stabdards : basic design, bs 5352 & ansi b16.34 socket-weld (s.w) ansi b16.11 threaded end (s.e) ansi b1.20.1 valve test and inspect :api 598 standard material: a105n, lf2, f5, f11, f22, f304, f304l, f316, f316l.

We are offering forg check valve, horizontal check valve lift check valve - class 800 forged steel check valve features : reduced or full port lift or swing chek valve spiral wound gasket of stainless steel bolted cap socket weld or threaded ends replaceable or integral hardfaced seat applicable stabdards : basic design, ms-sp-118 & ansi b16.34 socket-weld (s.w) ansi b16.11 threaded end (s.e) ansi b1.20.1 valve test and inspect :api 598 standard material: a105n, lf2, f5, f11, f22, f304, f304l, f316, f316l.

Features Bolted Bonnet Or Welded Bonnet Spiral Wound Gasket Of Stainless Steel Integral Hardfaced Seat Compact Outside Screw & Yoke Applicable Stabdards Basic Design BS 5352 & Ansi B16.34 Face To Face Ansi Inspect :API 598 Flanged End (F.E) Ansi B16.5 Valve Test And Inspect :API 598 Standard Material: A105N, LF2, F5, F11, F22, F304, F304L, F316, F304L

Features Bolted Cap Spiral Wound Gasket Of Stainless Steel Lift Or Swing Check Valve Integral Or Replaceable Hardfaced Seats Applicable Stabdards Basic Design, MS-SP-118 & Ansi B16.34 Face To Face Ansi B16.10 Flanged End (F.E), Ansi B16.5 Valve Test And Inspect: Api 598 Standard Material: A105N, LF2, F5, F11, F22, F304, F304L, F316, F316L.

Description of Parts TEST PRESSURE Hydrostatic proof tests are carried out as per BS 5146, MSS SP 72 ANSI B 16 34

Salient features of spring loaded disc type non return valve: • investment casting body construction • compact & rugged design • stronger, liter and smaller than conventional swing check valve, hence less expensive to install and maintain • single disc type • spring loaded disc to prevent reverse flow in pipe line • easy to installation between two pipe flanges • metal to metal or soft seat option • maintenance free design • zero leakage (in soft seat) • full port opening • less pressure drop • wafer, flangeless, sandwich type • shorter length, required minimum space • offer any 3rd party or client inspection.

We are dealing in ci ball valve, Our main products include different Flow set valves like Globe Valve, Gate Valve, Disk Check Valve, Ball Valve, Needal Valve, Steam Trep Valve, Socket etc. Now, we are looking forward to expand our business by extending our reach up to new markets and clients.

Size : 1.1/2inch, 1.1/4inch, 1/2inch, 1inch, 2inch, 3/4inch

Material : Cast Iron

Application : Gas Fitting, Oil Fitting, Water Fitting

Color : Sky Blue

Feature : Blow-Out-Proof, Casting Approved, Investment Casting

Pressure : High, Low, Medium

Number Of Way : 2way

Country of Origin : India

Features Reduced Or Full Port Lift Or Swing Chek Valve Spiral Wound Gasket Of Stainless Steel Bolted Cap Socket Weld Or Threaded Ends Replaceable Or Integral Hardfaced Seat Applicable Stabdards Basic Design, MS-SP-118 & Ansi B16.34 Socket-Weld (S.W) Ansi B16.11 Threaded End (S.E) Ansi B1.20.1 Valve Test And Inspect :API 598 Standard Material: A105N, LF2, F5, F11, F22, F304, F304L, F316, F316L.

Available Sizes 15MM | 20MM | 25MM | 32MM 40MM | 50MM | 65MM 80MM | 100MM Material / Pressure C.I Casting, Nylon Ring, Ms Ball MS Pin, Commercial Bage