Biomass Dryer Dealers in Rajkot

In the Flash Dryer system, Input Biomass (with Higher Moisture) feed in a screw Conveyor mix with hot air. Hot Air which is generated from furnace passes with wet Biomass in duct line. Due to ID Blower developed negative pressure in full system up to duct line.Moisture liberated from biomass due to more than 100.C Temperature inside system. Due to maximum Contact time and surface area moisture evaporate and separated threw blower discharge. At the bottom of Cyclone dry biomass collected and discharged threw RAV- rotary air lock valve. Moisture (Steam) and flue gases pass to ID fan to Bag house or Chimney. Application : Flash Dryer is used for Drying Biomass like sawdust, Bamboo dust, sugarcane bagasse etc. Output Capacity of Flash Dryer : Output Production Capacity - 1500 Kg/Hr. ( If input Moisture % Max. 30%) Input Moisture Percentage - 30% Output Moisture Percentage - 10% Water Evaporation Capacity - 400 Kg/Hr. Output Capacity : If moisture percentage is more then 30% Output prouction capacity will be propotionally less. Output drying capacity is depend on input material moisture % System Specification : Type of Dryer - Flash Type Dry Threw - Hot air System Pressure - Negative/suction Fuel in Furness - Solid coal ( Briquettes/Fire Wood) Technical Specification : Blower - 25 HP Rotary Air Lock Valve - 1 HP Screw Conveyor - 3 HP Atomization for Operating : Feeding conveyor speed is operating as per cyclone outlet set point temperature. Servo control valve is operated as per desire temperature for system. Land Area & Size ( Approx) : Length - 20 Feet Width - 15 Feet Height - 20 Feet Silent Futures of Radhe Engineering Co. - Flash dryer : Maximum travel length with Hot air. Completely atomized feeding threw VFD drive as per operating parameters High capacity ID Blower Servo control valve to mix blend fresh air to desire input temperature from furnace Dust collecting system to as for control dust pollution. Temperature sensor at all required location to support atomization as a set point.

• Techinical Specification:  
•  : MOISTURE EVAPORATION CAPACITY
• :: 45Okg./hr.
• OUTPUT: :
• 1500 kg./hr.: MAXIMUM INPUT MOISTURE
• :: 35.00%
• OUTLET MOISTURE: :
• 15.00%: CENTRIFUGAL FAN MOTOR
• :: 15 HP
• VIBRATING SCREEN: :
• 2 HP: SCREW CONVEYOR MOTOR
• :: 2 HP

• size: 30 x 15 or 25 x 25
• Moisture Evaporation Capacity: 450 Kg. /Hr.
• Output: 1500 Kg. /Hr.
• Maximum Input Moisture: 35%
• Outlet Moisture: 15%
• Centrifugal Fan Motor: 15 Hp
• Vibrating Screen: 2 Hp
• Screw Conveyor Motor: 2 Hp

Turbo Dryer is also known as Column Turbo Dryer (CTD) which is utilized for the Drying Purpose for all such Raw Material which is having high moisture content up to 30-35% such as fibrous material such as Bagasse, Jute, Coir Pitch, EFB Palm Waste etc from which moisture evaporates at the acceptable limit of 12%.

• Moisture Evaporation Capacity: 450 Kg. /Hr.
• Output: 1500 Kg. /Hr.
• Maximum Input Moisture: 35%
• Outlet Moisture: 15%
• Centrifugal Fan Motor: 15 Hp
• Vibrating Screen: 2 Hp
• Screw Conveyor Motor: 2 Hp

Turbo Dryer is also known as Column Turbo Dryer (CTD) which is utilized for the Drying Purpose for all such Raw Material which is having high moisture content up to 30-35% such as fibrous material such as Bagasse, Jute, Coir Pitch, EFB Palm Waste etc from which moisture evaporates at the acceptable limit of 12%. GENERAL DESCRIPTION The system consists of screw conveyor, vibrating screen, feeding hopper vane guide, conveying line including insulated drying column and conveying line through which wet or moist material is conveyed with hot air.  A powerful low pressure open wheel centrifugal fan assures significant resilience time for removal of excess moistures. Material is conveyed to cyclone and discharged through air tap duct. WORKS Hot air temperature is kept according to the requirement from moisture of material. Your flue gas temp of 150 deg cent will not serve the purpose as material, even at 30-35 % moisture level, will require 300-350 deg centigrade. Also, for 50 % material, the temp may be used at about 500-550 deg cent. Flow rate will be around 10,000 cmh. The dryer is flexible at the joints, i.e., at the bends. So, you can take a 90 deg turn at any of the joints. Hence, including HAG, the dryer size could be 30 x 15 or 25 x 25 ft. with a height of about 29 ft. We recommend to use Hot Air Generator as Source for evaporating moisture from Biomass so that the Briquettes manufactured from such Biomass will be proved to be good Biofuel in Boilers  We use a SS chicken mesh at the outlet of furnace, which is sufficient to arrest any leftover spark in the flue gas, after it has travelled through 2-3 ups & downs in the Furnace. With 50 % input and 14 % output of Bagasse, CTD dryer will give an output of approx. 1500 Kgs/hr.

• Output Production Capacity: 1500 Kg/Hr.
• Input Moisture Percentage: 30%
• Output Moisture Percentage: 10%
• Water Evaporation Capacity: 400 Kg/Hr.

In the Flash Dryer system, Input Biomass (with Higher Moisture) feed in a screw Conveyor mix with hot air. Hot Air which is generated from furnace passes with wet Biomass in duct line. Due to ID Blower developed negative pressure in full system up to duct line. Moisture liberated from biomass due to more than 100.C Temperature inside system. Due to maximum Contact time and surface area moisture evaporate and separated threw blower discharge. At the bottom of Cyclone dry biomass collected and discharged threw RAV- rotary air lock valve. Moisture (Steam) and flue gases pass to ID fan to Bag house or Chimney.

• Color: Black, Blue, Brown
• Power: 12-15kw, 15-18kw, 18-21kw
• Warranty: 1-5 Years
• Features: Longer Life, Good Quality, High Strength
• Use: Industial

• Material: Mild Steel
• Automation Grade: Automatic
• Capacity: 1000-1500 kg/hr
• Country of Origin: Made in India
• Automatic Grade: Automatic
• Design: Standard

We make available fine quality Biomass Rotary Drum Dryer which has the robust structure. Our well-structured warehouse is properly maintained and installed with diverse amenities required for the safe storage of the products. Moreover, we keep on updating the unit for enhanced safety. Our experts ensure that payments are made on time and for that, we have online payment processing system to evade security issues. We have well maintained payment logs available for the convenience of our customers.

Biomass Dryer, Biomass Briquetting Machine, Biomass Hammer Mill