Plastic Coatings in Rajkot

If you are looking for a trusted company that provides excellent Arc Spray Coating service in Ahmedabad, rely on us. We have a team of diligent professionals, which has expertise in providing Arc Spray Coating service for different types of surfaces. We use highly advanced arc spray coating systems that ensure durability of the products. We provide Arc Spray Coating service to the clients as per the details given by them.

We are recognized as one of the most prominent Industrial FRP Lining Manufacturers Suppliers in the country. We are able to carry out the FRP Lining at site on the surface like RCC, MS, wall, floor, etc. The MOC, we are carrying out on FRP Lining, is as follows : Isopthalic ResinVinyl Ester ResinBisphenol ResinEpoxy Resins

• Grade Standard: Chemical Grade
• Form: Liquid
• Types: Penetrants
• Application Surface: Wood
• Surface Of Application: Stone
• Appearance: Clear liquid
• Best Before: 12 Month
• Method of Application: Brush Or Air Less Spray
• Active ingredient: ca. 55 %
• Specific gravity: at 20 degree C ca. 0.95g/ cm 3
• Pack Type: Plastic Can
• Size: 1 liter

These are solvent or water based, fusion inhibiting, refractory coatings to be applied on mould walls or cores primarily to give good surface finish and consistent casting quality. This is achieved by Enabling better molten metal flow characteristics thus enabling better filling in intricate mould cavities Preventing surface defects such as metal penetration, sand burn-on (fusion), carbon pick up, sand expansion defects (such as veining, rat tail, finning etc.) or lustrous carbon defect. Preventing mould wall erosion and thus subsequent inclusions in molten metal Improving stripping characteristics of castings

We are offering a wide range of FRP lining to our valued clients. We offer a excellent quality products to the clients.

Protective Coatings, energy savings, high temperature leak-resistance, insulation, fire protection and low friction. Ultra-Therm ULTRASLIDE - HT Ultraslide - S Ultracoat FP Ultra -ZCOAT Duraback Ultra Protect - SPL XTRA GRIP

• Finish: Flat
• Colour: White, Clear & Gray
• Clean – Up Thinner: Soap and Warm Water
• Sp. Gravity: 1.4-1.5
• % Age Solid: <65
• Flash Point: None
• Practical Coverage: 60-100 sq. Ft/gallon, depends on the surface, method of application and the thickness of the film.

A premium quality 100% Acrylic elastomeric coating specially formulated for waterproofing to form a seamless membrane, which is resistant to sunlight, heat, water and most chemicals, typically used as waterproofing and as a topcoat for roof coating to protect the UV rays for reducing heat at bottom. It provides superior protection to built-up and gravel roof systems, may also be used on galvanize steel, concrete and urethane foam roofing, it gives outstanding durability because of its UV protec Features Forms a flexible coating that protects against UV rays, Heat and pounded Water May also used on metal, wood, Concrete and Masonry Surfaces May also used on Galvanized Steel Surface Preparation Surface must be clean, dry and free from dust, grease, mildew and wax remove any loose and peeling parts and prime with America’s colour primer. If surface is glossy should be sanded to a dull finish If mildew is present the surface should be washed with chlorine bleach solution (20% household bleach and 1% liquid detergent in warm water) If Concrete is new then allow for 30 days prior to application The PH of Concrete should be less than 10, check by PH paper, if Surface is not within the 10 PH and large amount of efflorescence. (efflorescence is seen as a white salty deposit on the concrete surface) are present then the concrete should be acid etched prior to painting ( etching solution is 1 part of commercial HCL and 3 parts of water mix) and apply uniformly the wash with clean water and allow to fry the surface. The Concrete must be dry prior to coating (less than 12% moisture content) but f the surface is totally dry then spray little water on the concrete prior to painting will help the paint to penetrate into the concrete. Latex base sealer or Primer must be applied first to reduce the exposure to alkali conditions

We are offering surface coatings hand anodizaing aluminum component coatings are a special process and a demanding science. The company established facilities to hard anodize fully machined forged aluminum components. Hardness in the range of 400 – 450 hv can be achieved on the surface, making the product virtually wear proof and anti file. The plating thickness ranges from 0.015mm to 0.060mm. The company also specializes in providing different colours in anodize plating. Apart from hard anodizing the company also performs the following plating. tin plating. (immersion process) graphite coating. (spray process) graphite screening. (screen printing process)

Epoxy Polyester Powder Coating, Powder Coating Powder, Powder Coating

high temperature refractory coatings, Binders Foundry Coating

We are doing frp lining any metal and as per customer specification.

surface coatings, concrete repair, mortars, industrial flooring

Epoxy Polyester Powder Coating, Epoxy Powder, epoxy polyester powder

Protective Coating, Anti-carburizing paint

Wall Coating, acid proof cements, Stone Flooring, acid proof cement mortar

ss powder coating

Epoxy Coating, of epoxy floorings, Epoxy Painting, water proofing services

building coating, Waterproof Materials, Construction Chemicals, Plasticizer

Epoxy Coating, Tile Adhesive, surface treatment, Sealant, Floor Hardener

Frp Lining, Cooling Towers, Air Ventilator, plain sheets, erp door

PU Coating, Paints, Water Based Paints, designer paints, Wood Coatings

Powder Coating, Auto Parts, Casting Parts, Aluminum Casting Parts

industrial coating, ceramics tiles, decorative arts, Paints

Powder Coating, Powder Coating Services, Powder Coating furnace

Epoxy Coatings, acrylic polymers, conctrete admixture

stainless steel powder coating

Coating, Monel Sand Casting, Springs, Precision Investment Castings

Epoxy Coating, Automotive Paints, Synthetic Enamel, Primers, Paints

Coating

Powder Coating, power coating, plastic coating, polyethylene coating