Ultra Technologies Sipcot, Ranipet, Tamil Nadu

Elastomeric Waterproof Coating (Ultra Cote- 2P) is a two-component acrylic modified cementitous coating to waterproof and resurface concrete & masonry. Elastomeric Waterproof Coating (Ultra Cote- 2P) is simply applied by stiff brush, roller or trowel to form a waterproof flexible coating. Elastomeric Waterproof Coating (Ultra Cote- 2P) provides an affective barrier to waterborne salts and atmospheric gases. Fluid applied Elastomeric Waterproof Coating (Ultra Cote- 2P) provides hard-wearing, seamless waterproof membrane for roofs& foundation protection. Applications As a waterproof lining for water-retaining structureFor coating seawater channelsTo provide foundation protectionAs a waterproof coating for roofsTo protection the concrete surface from carbonation& chloride attacks Advantages 1MM COATING PROVIDES anti-carbonation coverResists up to 70 meter head pressureExcellent Bond strengthSuitable for contact with drinking waterBreathable & flexible coatingResistance to carbon dioxide and chloride ion diffusion Properties Pack A : Milky white liquidPack B : Grey powderMix Ratio : 2:1(B: A)Density : 1.8kg/m3Water penetration : Nil 7 back at 2mm diffCoverage : 1.8 kg/m2/1mm Packing : 15 kg Applications In Surface Preparation, removes all grease oil, dust particles. The surface should be free from any contaminant surface should be wet. Directions Elastomeric Waterproof Coating (Ultra Cote- 2P) is pre-weighed and mixed using clean bucket. Do not add extra water. Apply the mixed material on a prepared wet surface using brush (or) roller. Apply the second coat after 3 hours of 1st coat. Storage : Keep in a cool & dry place Safety : Avoid contact with eyes, mouth, and skin. Splash water immediately if spilled.

Elastomeric Waterproof Coating (Ultra Cote-PUS) is a two-component acrylic modified cementitous coating to waterproof and resurface concrete & masonry. Elastomeric Waterproof Coating (Ultra Cote-PUS) is simply applied by stiff brush, roller or trowel to form a waterproof flexible coating. Elastomeric Waterproof Coating (Ultra Cote-PUS) provides an affective barrier to waterborne salts and atmospheric gases. Fluid applied Elastomeric Waterproof Coating (Ultra Cote-PUS) provides hard-wearing, seamless waterproof membrane for roofs& foundation protection. Applications As a waterproof lining for water-retaining structureFor coating seawater channelsTo provide foundation protectionAs a waterproof coating for roofsTo protection the concrete surface from carbonation& chloride attacks Advantages 1MM coating provides anti-carbonation coverResists up to 70 meter head pressureExcellent Bond strengthSuitable for contact with drinking waterBreathable & flexible coatingResistance to carbon dioxide and chloride ion diffusion Properties Pack-A : Milky white liquidPack B : Grey powderMix Ratio : 2:1(B: A)Density : 1.8kg/m3Water penetration : Nil 7 back at 2mm diffCoverage : 1.8 kg/m2/1mmPacking : 15 kg Applications For surface preparation, removes all grease oil, dust particles.The surface should be free from any contaminant surface should be wet.Elastomeric Waterproof Coating (Ultra Cote-PUS) is pre-weighed and mixed using clean bucket. Do not add extra water.Apply the mixed material on a prepared wet surface using brush (or) roller. Apply the second coat after 3 hours of 1st coat. Safety : Avoid contact with eyes, mouth, and skin. Splash water immediately if spilled. Storage : Keep in a cool & dry place.

Acrylic Polymer Waterproof Coating (Ultracrete-L) is an acrylic Polymer based waterproof coating. Acrylic Polymer Waterproof Coating (Ultracrete-L) is used for waterproofing of basements, toilets, terraces, roofs etc., general concrete repairs and protection of concrete against corrosion, salt attack. Features Combines a tough, hard-wearing surface with waterproofingAllows trapped vapors to escape without peeling and blisteringCan be applied in uniform thickness to horizontal & vertical surfaceDevelops excellent bond to most building materialsPrevents salt penetration into concreteHighly durable in continuous wet condition Surface Preparation The surface shall be cleaned to remove all dust, loose particles and free from oily surface. All concrete surfaces should be pre-wetted.Depressions are filled and leveled using Ultra Crete, cement & fillers Application Acrylic Polymer Waterproof Coating (Ultracrete-L) is mixed with neat cement in the ratios of 2 part cement: 1 part polymer.The mix has to be stirred thoroughly without any lumps formation.The mix has to be applied by brush on a prepared surface.Two or more coats are recommended.Second coat should be applied by wetting the first coat.After 6 hours of application, moisture curing to be done for next 24 hours for 2 � 3 times. Coverage : For slurry coats � 1 � 1.2m2 @ 0.4mm/2 coats Brush Topping Ultracrete : 0.5 KgCement : L 1.0 Kg (0.75 m2)Silica Sand 60/80 : 1.0 Kg Note : Please consult or refer detailed individual application sheet for different waterproofing systems.

Coal Tar Modified Epoxy (Ultrapoxy-CR) is a solvent free two pack high build Epoxy Resin System. Coal Tar Modified Epoxy (Ultrapoxy-CR) is specially designed for high chemical resistance coating for concrete structures. We make Coal Tar Modified Epoxy (Ultrapoxy-CR) available at the best prices in the market. Features / Advantages Solvent free and durable coatingCan be easily applied by brush or rollerExcellent adhesionAbrasion resistantHigh Chemical resistance over wide range of chemicalsCan be applied to get a 250-300 microns thickness in two coats Typical Applications For lining effluent tanks, chemical storage tanksChemical resistant floorWalls of battery rooms & chemical industriesHeavy oil spillage areas of chemical and mechanical industrial floors Technical Details Solid content : 100%Mix ratio : 3:1 by weightPot Life : 45 minutes at 30oCTack free time : About 4 to 6 hours at 30oC.Initial cure : 24 hours at 30oC.Full cure : 7 days at 30oC.Over coating time : 24 hours Directions For Use Surface Preparation The surface has to be dry, sound & free from loose particles. This can be achieved by grit blasting or sand blasting or grinding and water jetting. The surface should not have moisture content of more than 4%. The surface should not contain any laitance, grease, oil or any other contamination.Mixing The pre-weighed ready to use components of Coal Tar Modified Epoxy (Ultrapoxy-CR) are mixed thoroughly with a mechanical stirrer with rpm of 300-350. The mixing should be done till it gets a homogenous color of the mixed material. Applications The material is applied on the well prepared surface by a standard paintbrush, good quality lamb wool roller or sprayed with airless spray equipment. Care should be taken to ensure continuous film and proper material consumption. Coverage : The coverage will be 2.5- 3.5 m2/kg per coat Storage And Shelf Life : 1 year (Store the material at a cool and dry place at 25oC) Cleaning Of Tools & Equipment : Clean with solvents Packing : 20Kg Precautions Should be applied with gloves and care should be taken to see that it does not fall on eyes. Splashes on to the skin have to be cleaned only with plenty of water only and medical advice has to be taken.

Coal Tar Modified Epoxy (Ultrapoxy-CTE) is a high build two pack waterproofing and anticorrosive system based upon epoxy resin, coal tar and amine curing agents. These agents in Coal Tar Modified Epoxy (Ultrapoxy-CTE) are specially chosen for their ability to withstand high degrees of corrosion and also for mild chemical attacks. We offer Coal Tar Modified Epoxy (Ultrapoxy-CTE) at the most competitive prices in the market. Features / Advantages Easily applicable by brush or trowelSeals localized cracks and surface porosityBonds strongly to most of the building materialsNo primer is requiredCures to a tough elastic waterproof filmExcellent resistance to chemical aggression Typical Applications Protective, waterproofing system for building roofsAnticorrosive coating for mild steel structures Technical Information Nature : Two-component LiquidColor : BlackMixing ratio part by weightPart I (B) : 90Part II (H) : 10Solid content: Part I : 65%Pot life at 30oC : 3 ½ - 4 hoursInitial hardness at 30oC : 24 hoursFull cure at 30oC : 6 to 7 daysCoverage : 30-35 sq. ft. / literRecoat ability : 12 hours Below 20oC these timings may be increased Direction for use Surface Preparation : It is essential that Coal Tar Epoxy is applied to clean dry substrate in order to achieve maximum adhesion between the coating and substrate. All loose particles should be removed by brushing scraping or acid etching.Mixing : Coal Tar Epoxy is supplied in pre weighed packs which are ready to use on site. DO not add extra solvents or thinner, thorough mixing is essential.Cleaning : Tools and equipment can be cleaned immediately with solvents like xylene, acetone etc.Storage and Shelf Life : 12 months shelf life if stored below 35oC and 50% R.H. Packing 1 liter5 liters20 liters Direction for use Bare Steel : All surfaces shall be free of rust, mill scale, and contaminants such as oil, grease, dirt, and salts. Before any surface preparation is attempted, oil and grease must be removed by employing SSPC- SP1 solvent cleaning. Precaution Danger!Flammable!Contains xyleneKeep away from heat, sparks and flame. Avoid breathing vapor.Use with forced air ventilation in confined areas.Avoid contact of resin or hardener with skin or eyes.In case of eye contact, flush immediately with plenty of water and consult a physician.Do not take internally.Not to be applied when air and surface temperatures are below 50oFMust be top coated with appropriate coating when used in corrosive environmentsCaution when opening containers- gassing may occurNot for immersion or for exposure to acids & alkalis without proper topcoats

Acrylic Polymer Cementitious Coating (Ultrafix) is an acrylic polymer based cementitious ready to use tile adhesive for ceramic, mosaic, marble and cement tiles. Acrylic Polymer Cementitious Coating (Ultrafix) can be applied in tile on tile form. We make Acrylic Polymer Cementitious Coating (Ultrafix) available at the best prices in the market. Features Excellent Bond StrengthLonger pot life up to 2 hoursGood Waterproofing Water curing and soaking is not requiredFast laying of tiles that reduces labor costEco FriendlyTile fixing permanent Technical Data Color : GreyForm : Dry PowderBond Strength : More than 20 kg / m2Coverage : 1.8 mo / 2mm / 6 KgWater powder Ratio : 28±2% Application Surface Preparation : The surface must be free form dust, grease and oil. No need to soak tiles.MixingAdd 280 � 300 ml water by weight of Acrylic Polymer Cementitious Coating (Ultrafix) depending on the climatic condition.Mix the powder to water until a uniform paste is obtained. Spread out the paste to a uniform thickness by notched trowel.Place tiles firmly on Acrylic Polymer Cementitious Coating (Ultrafix) bed ensuring good contract with tile. Packing (In HDPE bags) 20kg50kg Advantages Of Ultrafix Over Plain Cement Sand Mortar Thick bed is required (8-10mm) for plain mortar, where as thin bed is sufficient (2-3 mm) for CTA. (Cementitious Tile adhesive)Curing is required for plain mortar. In case of CTA no curing is requiredAdhesive strength of plain mortar is very less (less than 4kg/cm2). In case of CTA adhesive strength is around 10kg/cm2 i.e., 2-5 times higher than the normal mortar.Failure rate is nil in case of CTA when properly applied Function Of Tile Adhesive Tile Adhesives are slightly flexible in nature.This flexibility accommodates the irregular expansion and contraction of two different types of materials, i.e., adhesive and tile. On the other hand conventional cement sand mortar or cement paste does not exhibit any flexibility. This results in delaminating of tiles from the concrete or plastered surface.

Concrete Etching Agent (Ultra Cleaner) is a composition of acid base material, inhibitors of corrosion and dispersing agents. Basically, Concrete Etching Agent (Ultra Cleaner) is a bluish liquid. The company makes Concrete Etching Agent (Ultra Cleaner) at competitive prices in the market. Advantages Safe with metals, wood, glass, plastic and rubberNo corrosive actionPenetrates oil and grease Uses For the removal of hardened concrete from tools, machinery and equipment, or rust and mill scale from steelwork.For the removal of mortar and plaster runs, droppings and stains from brickwork and concrete surfacesSuitable for etching of concrete floors and surfaces prior to application surface coatings Properties Appearance : Bluish liquidSpecific gravity : 1.075+0.002 Application Instructions Cleaning brickwork A tiny trial area should be cleaned first to determine the most suitable Ultra cleaner cleaning agent dilution.Pre-wet the brick-work, and rub the affected areas, using a sponge, with a solution of Ultracleaner cleaning agent and water.Strength of the solution required will vary but should be between 1:1 and 1:4 (by volume of Ultracleaner cleaning agent to water).Immediately wash down thoroughly with clean water when the action was finished. The Large Equipment Cleaning (Barrows, concrete mixers, Readymix trucks, etc.) Ultra cleaner cleaning agent should be liberally applied to the deposits by a soft broom and allowed to soak overnight if possible.If the surfaces of the deposit can be cracked by mechanical means, it will speed up the operation.In many cases more than one application may be required.On final stage, dissolved deposits and loose material should be wire brushed and washed away with clean water. Small Tools Cleaning Use Ultra cleaner with a dipping methodThe tools should be soaked in one night, then taken out and washed with clean water to remove all loosely adhering materials.Care should be taken to avoid prolonged contact between Ultracleaner and zinc or aluminium parts of tools like rivets, etc. Concrete Floors Cleaning Pre-wet floors and then, using a stiff bristle broom, brush the affected areas with a solution of Ultracleaner and water.Strength of the solution required will vary but should be between 1:1 and 1:4 (Ultracleaner cleaning agent to water)Immediately wash down thoroughly with clean water Removal Of Rust And Mill Scale Pre-wet the floors and then, using a stiff bristle broom, brush the affected areas with a solution of Ultracleaners and water.Strength of the solution required will vary but should be between 1:1 and 1:4 (ultra-cleaner to water). When the action has finished, wash down thoroughly with clean water. Wire brush again to remove remaining loose material and finish by thoroughly washing down with clean water.Repeat if necessary.High degree of rust or scale can be removed by soaking in the Ultracleaner solutions for 1 hour. Etching concrete floors For etching surfaces to remove laitance and give a mechanical key before applying resin or other coating, Ultracleaner cleaning agent should be diluted with water and applied at the rate of approximately 1 liter per 2 sq. meters.The dilution will depend upon the condition of the floors and the degree of etching required, but normally it will be between 1:2 and 1:4.When the action has finished, wash down thoroughly with clean water. Note : As treatment with Ultracleaner can alter the surface finish of concrete, the minimum concentration necessary for effective removal of stains should be employed. The surface should be washed down with water immediately after the treatment is complete. Packing ( in barrels) 1 liter5 liters20 liters200 liters Shelf life : At least 1 year in original sealed containers under normal warehouse conditions Precautions Health & SafetyUltracleaner cleaning agent is acid based and should be handled with care. It attacks zinc, aluminium and putty.If in doubt about its effect on a material, test a small area before application.Avoid contact with skin. Rubber gloves and goggles should be worn.Wash spillages with plenty of water.Enclosed areas should be well ventilated.If contact with eyes occurs, wash immediately with water and seek medical advice.Fire : Ultra cleaner is non-flammable. Additional Information Technical data and guidance can be provided on a wide range of admixtures, concreting aids, grouts, repairs and the range of industrial flooring systems which includes nonmetallic floor hardeners, epoxy floor coatings and self-leveling floor toppings, epoxy heavy duty abrasion resistant screeds.Separate data sheets are available on these products.

Floor Hardener (Ultrafloor-SOF) is a �Ready-to-use, shake-on-floor Abrasion Resistant Floor hardener. Floor Hardener (Ultrafloor-SOF) is used for wearing surface for industrial floors. Floor Hardener (Ultrafloor-SOF) is recommended for factory floors and warehouse surfaces that require abrasion resistant floor. Features Wear resistance & high abrasion resistant floor surface.High impact resistanceIncreased surface densityIncreases to resistancePenetration by oil, grease, hydraulic fluids and many industrial chemicals Application Procedure Base concreting The base concrete should be sound and placed.The water: cement ratio should be kept to a minimum consistency by using ULTRAFLO- N to produce a fully compacted concrete without excess water coming to the surface. Care must be taken to level the surface throughout the trowelling operation. Application Floor Hardener (Ultrafloor-SOF) should be sprinkled in two equal stages evenly on the surface of the freshly laid concrete as soon as the surface water has evaporated.Immediately after sprinkling of ULTRAFLOOR-SOF trowelling should be carried out either by hand or power float, when the surface has sufficiently stiffened as second trowel ling should be given to close any pores and remove any undulation in the surface.This should be followed by a final hand trowelling to remove any disc marks.The floor must be thoroughly cured. Coverage Coverage varies on types of floors. Medium duty : 5 Kg/m2Heavy duty : 7 Kg/m2Extra Heavy duty : 9 Kg/m2 Packing : Available in 50 Kg HDPE Bags

Integral Waterproofing Compound (Ultra Super) is a normal setting cement integral waterproofing compound with normal plasticizer in liquid form. The Integral Waterproofing Compound (Ultra Super) is a blend of specialized active ingredients to make concrete waterproof when there is permeability. Uses : Used in RCC / Concrete intended for water tank, roof deck, basement, lift pit. Features Permeability of concrete is improved.Due to increased cohesion, segregation and bleeding is reducedImproved workabilityImproved surface finish Application : Add measured quantity to mixing water. Then add solution to the cement sand mix. Technical Data Color : Brown liquidS.G. : 1.06 ±0.02Chloride Content : 0.1%Dosage : 200 ml per 50 Kg Cement.

Mineral Admixture (Ultra Tuff-MS) is a dry, compacted, silica fume based high performance product. The Mineral Admixture (Ultra Tuff-MS) is used to produce high quality concrete by reacting chemically within the concrete to increase the amount of calcium silicate hydrate gel formed. This way, the strength of the Mineral Admixture (Ultra Tuff-MS) is improved and the concrete is produced by filling the voids between cement particles. The reduced permeability of concrete produced with Mineral Admixture (Ultra Tuff-MS) greatly limits the ingress of chlorides, sulfates and aggressive chemicals promoting reinforcing at steel corrosion and open distresses in concrete. Advantages Improved durability and compressive strengthLow permeabilityFreeze and their resistanceBetter Chemical resistanceBetter flexural strengthCorrosion protection Uses Basement structures.Parking decks.Bridge decks.Marine Structure.Pre-stressed concretePrecast concreteReady Mix concrete Direction for use : It is recommended to be used with a high range water reducer to provide better workability while maintaining the desired low water-cement ratio. Dosage : Used at the rate of 5-10% by weight of cement, depending in the amount of strength increase and impermeability required. Packing : 25 Kg HDPE Bags.

The company offers Liquid Alkali (Ultrashot- LAF). The Liquid Alkali (Ultrashot- LAF) is a concrete admixture based on liquid free accelerator. The Liquid Alkali (Ultrashot- LAF), offered by the company, has an excellent accelerating property. Added to that, the Liquid Alkali (Ultrashot- LAF) has numerous uses as well as features. Uses : Can be used to either produce a workable flowing concrete without loss or strength to enable reduction to be made which results in a dense, water light concrete with higher, easy and ultimate strength. Advantages Improved workabilityHigh early strengthImproved durabilityBond strength of concrete to reinforcement is increasedReduces corrosion of embedded steel.Increased compressive strength Technical Data Form : Straw color liquidS.G. : 1.35 ±0.05Chloride content : NILCompatibility : Can be used with all types of cement.Method of use : Mixed with gauging water and then added into concrete mix.Dosage : Max 7 % by weight of cement.Packing : 250 by DrumStorage : Store in a normal ambient

Non Shrink Grout (Ultra Grout-50-70) is a non-shrink, non-ferrous grout that is easily mixed for grouting at any consistency i.e. dry-pack, plastic or pourable. Non Shrink Grout (Ultra Grout-50-70) does not contain any iron particles, chlorides or gypsum and will not corrode, shrink, rust or ravel even under constant moist conditions. When mixed according to instructions, it produces a high compressive strength due to a technology that reduces the water-cement ratio. Benefits Retain its workability for 2 hours.Ready to use, just addition of water is required.High density, increases bond to metal, wool and other construction materialsWill not rust, bleed.Requires no special treatment.Clean finishDensity increases wear ability, permeability withstand heat & thermal shock.Water tight, resist freeze & thaw water conditions and salt penetration.Resists a variety of oils & ChemicalsContains no free lime will not produce efflorescence. Applications Ultra Grout is recommended for grouting the following. Heavy equipped & machinery basesStructural columnsPump & equipment basesPower Line stations.Pre-case Tee jointsRe-pointing mortar jointsStructural cracksBearing PlatesRail posts, seating boltsPost tensioned cablesPatching Water Requirements Plastic : 0.14Flowable mix : 0.16Fluid mix : 0.18 Mixing and Proportions Add required water to get consistency. For uniform mix, use paddle or drum type mechanical mixers. Do not mix more than 5 minutes. Place grout after mixing. The working time of grout is 2 hours. Surface Entrapments First remove all dust, oil, grease or contaminants from surfaces to be grouted, and then remove all loose material. Metals which will come in contact with grout must be derusted or freed of paints, oils & greases. To avoid entrapment of air, provide air relief openings where required. Prior to placement of grout, thoroughly soak or dampen all concrete areas to be grouted. Then remove excess water from voids & holes. Forming For machinery bases and column base flats, follow standard forming procedures, which permit complete and proper placement of fluid grout, including use of head forms. All support elements should be anchored to prevent movements. Do not remove supports until grout has sufficiently hardened. Wool surfaces, which absorb moisture, should be pretreated with forming oils. Specifications Ultra grout needs the following: ASTMC_1107 � Standard SpecFor packaged dry, hydraulic cement grout ( Non-shrink)CRD-C 621-89, specification for non-shrinking grout.CRD-C 614, method of test for time of setting of groutASTM � C � 109 standard test method for compressive strength Properties Appearance : Cementitious grey powderWet density : 2200±20 Kg/m3Expansion : Min 1.0%Modules of elasticity : 4.5 x 10 Packing : Available in 50 Kg HDPE BagsShelf life : When stored in original, unopened pack, one year.

Polysulfide-Based Joint Sealant (Ultraseal-PS) is a two pack Polysulfide-Based Joint Sealant for vertical and inclined expansion/contraction joints. When two packs of Polysulfide-Based Joint Sealant (Ultraseal-PS) are mixed, it forms tough, flexible, durable rubber like material with strong adhesion properties on most building substrates and joints. Standards ASTM-C-920.BS-4254 Features Long lasting elasticityHigh movement capacityExcellent adhesionGood chemical and fuel resistance Uses : Used to form long lasting weather resistance and waterproof seals in joints subject to regular movement. It is used in underpasses, tunnels, basements, pre-cast concrete elements, bridges, runways and rigid pavements. Surface preparation : All surface must be clean, dry and free from any loose particles, grease, or oils. Correct joint designs should be followed use primer on both inside surfaces of the joints. Joint Design Minimum joint depth- 8mmMaximum joint width �40mmWidth to depth ratio up to 10mm �1:1For 10 to 40mm width : Depth ratio �2:1 Mixing : Mix both packs of sealants at the ratio of 92:8 by weight by paddle type mixture to a smooth uniform consistency place t he uniformly mixed sealant into the joints by tapping. Technical Data Pack A : White pastePack B : Black pasteMix ratio : 92: 8Movement capacity : +25%Pot life : At 30oC - to 6 hoursCuring time : 21 daysDensity : 1550kg/cm3Shore : A hardness �20-25Service temperatures : Up to 80oCApplication temperature : 5 to 40oCShrinkage : Up to 0.5%Chemical resistance : Dilute acids, alkalis, ATF fuel, kerosene, diesel, petrol, lubricating oil, white spirit.Storage condition : Keep in a dry place and away from extremes of heat.Shelf life : One year if unopenedPacking : 1 & 3 kgs

The company offers the very best Water Reducing Admixture (Ultraflo-S). the Water Reducing Admixture (Ultraflo-S) is a concrete admixture based on Sulphonated Naphthalene Formaldehyde Condensate and an organic polymer. The Water Reducing Admixture (Ultraflo-S) has excellent plasticizing property and conforms to the ASTM C-494; IS 9103 � 1999. Uses : Can be used to either produce an workable flowing concrete without loss or strength to enable large water reduction to be made for the same workability which results in a dense, water light concrete with higher, easy and ultimate strength. Advantages Improved workabilityMinimize shrinkage.Improved durabilityBond strength of concrete to reinforcement is increasedReduces corrosion of embedded steel.Increased compressive strengthPossible cement saving. Technical Data Form : Brown colour liquidS.G. : 1.20 ±0.02Chloride content : NILCompatibility : Can be used with all types of cement.Method of use : ULTRAFLO-S should be mixed with gauging water and then added into concrete mix.Dosage : Max 2% by weight of cement.Packing : 25 & 200 by DrumStorage : Store in a normal ambient tent.

Concrete is the most versatile construction material and is widely used in a variety of constructions. However, along with correct composition and preparation it is essential to carry out proper curing of concrete in order to realize its advantages. A common method of curing such as, continuously spraying water on concrete surface and ponding etc. are inconvenient and also expensive. Evaporation of water from concrete will deprive it of its much needed water for hydration resulting in capillary-type pores, lower compressive strengths, chipping off on the surface and development of surface cracks. Liquid membrane-forming, concrete curing compound is based on the principle that concrete has enough water for uninterrupted hydration. Thus, the White Pigmented Curing Compound (Ultracure-WP) is an ideal option in such circumstances. The company offers the very best White Pigmented Curing Compound (Ultracure-WP) to the clients. the White Pigmented Curing Compound (Ultracure-WP) can be availed at the market leading prices. Scope Membrane-forming, ready to use, white colour emulsion of specially blended synthetic waxes, complying with ASTM C309-97For application on freshly cast concrete or newly exposed concrete surface after removal of formwork, to form a temporary membrane which will retain sufficient moisture for effective curing to take place.The membrane eventually break down and disintegrate after which the surface can be painted. It is used for concreting generally, but specially useful for large areas of concrete such as pavements, runways, bridge decks and industrial floors also for vertical or sloping surface as on chimneys, towers, silos, canal lining, columns and beams where water curing is difficult or unreliable. Uses Single application-forms moisture barrier for whole of curing period.No other curing necessary-eliminates using of water, Hessian or sand completely.Reliable-no risk erratic or poor curing and ensures cement hydration efficiently.Ensures hard wearing surface-minimizes risk of drying shrinkage, cracks and dusty surface.Protection against a �burning� of the fresh concrete surface which is exposed to strong solar radiation, further protects concrete surface against influence of aggressive atmospheric conditions.Easy and safe application, non-toxic and non-inflammableEco-friendly. Application : Should be applied following the final finishing operation and immediately after the disappearance of water seen from concrete surface. It is important not to apply the product WP hen standing water is still present on concrete. If the concrete has already lost some of its surface water then it is recommended to fog down the surface before application of the product. Application Equipment : Low pressure spray, roller equipment most preferred and generally used is a knapsack sprayer of the type commonly used in horticulture or pest control while spraying, the distance between the sprayer and the concrete surface should be approximately 1m. Thus an uniform coating is guaranteed. It should be made sure that the spraying is properly carried out. Recommended System One full coat until a continuous uniform film has been achieved Color : Bulk liquid-white Dry film-translucentTemperature : May be applied at temperatures range of 2oC to 50oCFlash Point : Not applicableSpecific Gravity : 1.0 + 0.02Thinning : Not requiredCoverage/Dose Rate : 2.5 to 5.0 m2/LitreDrying time : Approx.90 min. at 30oC Toxicity : Non-toxic Testing : Exceeds requirements of ASTM C309-97 for moisture retention in liquid membrane curing compound. Packing : Available in 20 & 200 Litre plastic bucket/barrel. Product Information : Although the basic formulation of our products generally remains unchanged. Production refinements arising from continuing research and evaluation program may occasionally result in marginal changes in properties. Technical Service Maintains a technical division with highly qualified Technical Personnel to investigate and advise on subjects related to concrete and The Construction Industry. The Division provides advice on the correct use and selection of right products at the right place.Undertakes Consultancy Service for diagnosis and rehabilitation of distressed structures.Undertakes jobs as a package for total waterproofing system with guarantee.

The company is a well-known Manufacturer and Supplier of Anticorrosive Coating. The Ultra Epoxy UEM 993 Anticorrosive Coating is modified epoxy resin which can be suitably formulated with hardeners like UH930, UH950, UH941 or UH940 and applied as anti-corrosive solvent-free coatings on surfaces. The Anticorrosive Coating is ideal where protection against corrosive environment is of prime importance. To name a few field of applications, the Anticorrosive Coatings are used on steel and concrete structures in chemical plants, oil refineries, marine installation, food factories, paper mill, civil structures, bridges, dams, lock gates, canal bottoms and banks, internal and external surfaces of steel or asbestos pipes storage tanks, reaction vessels and others. The solvent-less Anticorrosive Coatings can be applied by conventional brushings and trowel ling methods. In general, two Anticorrosive Coatings are applied: the first Anticorrosive Coating being the primer coat and the second being the top coat, However, the number of coats can be increased, depending upon the degree of abuse the surface is exposed to. Information On Processing Preparation Of Surface The preparation of surface over which the Anticorrosive Coating is to be applied is of primary importance for achieving the most optimum surface for better adhesion of the coating. If the surface is metallic it can be sand blasted or roughened with emery paper. The surface must be thoroughly cleaned and should be devoid cleaning may be done with solvents like tri-choroethlyene, carbon tetra chloride, toluene etc. Incase the concrete surface is too smooth, it can be roughened by treatment with dilute hydrochloric acid and followed by thorough washing with plenty of water till the washing is neutral top litmus. The surface then may be dried before application of coating.Mixing RatioPrimer CoatUltra Epoxy UEM 993 : 100 parts by weightHardener UH 941 : 80 party by weight Or Ultra Epoxy UEM 993: 100 parts by weight Hardener UH940: 50parts by weight The Resin and the Hardener can be mixed in a container manually till homogenous state is reached. The mix then can be applied as primer coat.Top Coat In preparation of the top coat, different rate of cure may be achieved with Ultra Epoxy UEM 993/ UH930/ UH950. Typical 3 ratios are indicated below as a guideline. Depending upon the actual requirement at the time of application, suitable proportions may be used. The first 2 mixing ratios are normally being used. Apart from the resin and hardener composition, some fillers like silica flour (250 mesh) can be used. In case of the coating being applied on a vertical surface, a thixotropic agent like IF9 Can be added in the mix to the tune of 5phr and thoroughly homogenized before application.Application After the surface is prepared, the primer coat van be applied by brushing or trowel ling as may be found suitable, up to a required thickness of coat. After the primer coat is applied, it may be allowed to stand at room temperature, till such time the coating becomes tacky to tough. At this stage, the top coat may be applied by brushing or trowel ling. In case, the primer coat has gelled into a hard mass, the surface may be lightly abraded with a sand paper and then the top coat may be applied. After the coating has gelled, it will take about 7 to 8 day to room temperature to attain the full cure. Such a Coating will exhibit very strong bond on to the surface and resistance against a wide range to chemicals. The heat distortion temperature of this system is slightly above 80*c.Coverage 1 kg of the mix of the above formulations will cover approximately 2 to 3 sq.m of the surface for a thickness of about 300 to 400 microns. However, the coverage will vary depending upon the porosity and degree of roughness of the surface.