Vindhya Telelinks Ltd Chorhata, rewa, madhya Pradesh

Up to 144 enhance low water peak single mode fibres in full compliance with ITU-T-G.652.D (also available with G655 G656 G657 SM Fibre and OM1 OM2 OM3 & OM4 MM Fibre) 246812 fibre per tube combinations are available in 6812 element construction Non metallic anti-buckling FRP rod as Central Strength Member (also available with Steel rod) Loose buffer tubes fully filled , S-Z Stranded Cable core fully filled with jelly (also available in dry core) Glass yarn can be used as peripheral strength member S-Z core wrapped with polyester tape water swellable tape UV Stablized HDPE inner sheath, Black Insect & termite resistant PA-12 outer sheath, Orange

Each conductor consists of a round wire of annealed high conductivity copper. Each conductor is insulated with solid mediumhigh density polyethylene insulation. Two insulated conductors are twisted with uniform lay to form a pair. The length of the lay of the pairs is so chosen that the cross-talk is minimum.10 or 20 No's of twisted pairs are laid up to form a group which constitutes a unit. Each unit should have an overlapping for color ID. In case of cables having more than 100 pairs, 5 units of 10 pairs or 20 pairs are laid up to constitute 50 or 100 pairs of super units respectively.

Each conductor consists of a round wire of annealed high conductivity copper. Each conductor is insulated with solid mediumhigh density polyethylene insulation. Two insulated conductors are twisted with uniform lay to form a pair. The length of the lay of the pairs is so chosen that the cross-talk is minimum. Suitable for installation in Hilly areasareas where digging is not possible

Conductor - Each conductor consists of a round wire of annealed high conductivity copper.Each conductor is insulated with Foam Skin Solid PE insulation. Foam Skin insulation consists of an extruded inner layer of uncoloured foam, covered by an extruded outer layer of coloured skin with required colours to meet the specification. For Solid insulation each conductor is insulated with Solid mediumhigh density polyethylene insulation.Two insulated conductors are twisted with uniform lay to form a pair. The length of the lay of the pairs is so choses that the cross talk is minimum. Armoured & Unarmoured construction —Availability of standard conductor sizes ranging from 0.4 mm to 0.9 mm diameter —Available in sizes up to 2400 pairs Suitable for installation in ducts— —Direct Burial application for armoured cable

Light Weight & Excellent Tensile Strength Prevent Cable buckling Most Suited for Multi-Loose Tube, Uni Tube, Slotted Core & Ribbon Cable Designs Used as central or peripheral reinforcement in fibre optic cable Dual Advantage : Reinforcement during installation as well as reduce stress on signal carrying optic fibre conductor Prevent sagging in aerial installation Cost effective solution as a strength memberIt is manufactured using E-glass fiber with heat resistant thermal resin system. It is available in various coatings including EAA, Tuff, Mega Bond and HDPE, which allows easy handling, Tuff coating provides very smooth surface, whereas Mega bond is suitable for where high adhesion to up jacketing is desired.

In power theft prone areas. As replacement of bare lines in rural areas, in woods, other localities & narrow street where space is limited. As replacement of bare lines where reliability of supply is of prime importance and where high degree of stability of supply voltage is of importance. In hilly terrains where cost of erection of overhead lines of under ground cable becomes very high. In hilly terrains where cost of erection of overhead lines of under ground cable becomes very high. As reinforcement of existing system without increasing voltage. For temporary supplies.

Aerial Bunched Cables are suitable for the following functions In power theft prone areas. As replacement of bare lines in rural areas, in woods, other localities & narrow street where space is limited. As replacement of bare lines where reliability of supply is of prime importance and where high degree of stability of supply voltage is of importance. In hilly terrains where cost of erection of overhead lines of under ground cable becomes very high. In hilly terrains where cost of erection of overhead lines of under ground cable becomes very high. As reinforcement of existing system without increasing voltage. For temporary supplies.

The phase conductor and neutralstreet lighting conductors is of H2 or H4 grade aluminium complying with the requirements of IS 8130:1984 and conforms to flexibility class 2 of IS 8130:1984. The size of the street lighting conductor is16 mm2. Safest system because phase conductors are insulated, no risk of danger of accidental touching live conductor. Less fault rage on account of good protection against line and ground fault by high winds or falling trees or bird especially in hilly areas & forests as encountered in rural distribution networks. High insulation resistance to earth in all seasons and polluted atmospheres. Negligible leakage currents and low losses. Multiple circuits of power and telephone cables could be strung in the same set of poles or any other supports like walls etc.

Thickness : 1.2 mm