Control Panels Dealers in Kupwad, Sangli

• Type: Electrical Control Panel Board
• Voltage: 110V, 220V, 440V
• Material: Mild Steel
• Power Source: Electric
• Phase: Single Phase, Three Phase
• Warrenty: 1 Year, 2 Years
• Autoamatic Grade: Automatic, Fully Automatic, Manual, Semi Automatic
• Brand Name: BFPL
• Surface Treatment: 7Tank Pre Treatment + Powder Coating

low voltage electrical switchboards & control panel.

HT outdoor and indoor switch-yard, Panels VCB/ SF6 panels, control systems, HT capacitor control panels Transformer protection systems Ring main units (Change over control panels), Relay panels Bus ducts, Unitized outdoor and indoor substation Control and Relay Panels for H.T. Switchgears controls

• Size: Multisizes
• Type: Electric Control Panels
• Application: Boiler Control
• Color: Brown, Grey
• Voltage: 110V, 220V
• Material: ABS
• Power: 1-3kw, 3-6kw
• Power Source: Battery
• Phase: Double Phase, Single Phase
• Warrenty: 1 Year
• Autoamatic Grade: Automatic, Fully Automatic, Manual

Gennext make ATS controller is designed to monitor Mains supply under voltage, over voltage, single phasing and reverse phasing and provides auto start signal to AMF controller on Mains disproportion.   FEATURES ATS controller is used to transfer the load from mains to DG and From DG to Mains very smoothly. It senses 3 phase Mains and DG supply. It reduces LVM, Timers and hence reduces the panel wiring It gives the protection for mains like UV/OV/SPP/RP and unbalance voltage. Settable power on delay, Trip delay, Load transfer delay and cool down delay. It shows Mains Phase and Line voltage readings LED indication for Mains ON, DG ON, Load ON Mains, Load ON DG Autostart input for DG mounted Amf controller. Site voltage calibration possible. Size: 96×96×85mm Cutout size:92×92

For optimum utilization of available power the reactive power consumption should be reduced or nullified i.e. power factor should be unity, hence, most of the Power Distribution companies have policy to penalize the industrial and commercial consumers for not maintaining power factor above certain limit (generally above 0.90 value). However, due to reactive power drawn by capacitive or inductive load in the consumer premises the power factor is either lagging or leading, thus to maintain it within limit i.e. for compensating or supplying required KVAR, the capacitors (in case of lagging PF) or reactors ( in case of leading PF) are connected across the system. For stable load the fixed KVAR compensation is required , while for variable load the KVAR requirement also changes as per the load duration cycle, thus in such case the Automatic Power Factor control Panel is installedElectric Power quality is a term that has captured increasing attention in power engineering in the fresh years. The power quality is mainly depends on the needs of the equipment that is being supplied. Usually the term it refers for maintaining a sinusoidal waveform of bus voltages at rated voltage and frequency. The waveform of electric power at generation stage is purely sinusoidal and free from any distortion. All the Power conversion and ingesting equipment are also designed to function under pure sinusoidal voltage waveforms. However, lots of devices that distorted the supply waveform. These distortions may spread all over the electrical network. In fresh years, there has been an increased use of non-linear loads, which has resulted in an increased fraction of non-sinusoidal currents and voltages in Electric Network. Classification of power quality areas may be made according to the source of the problem such as converters, magnetic circuit non linearity, arc furnace or by the wave shape of the signal such as harmonics, flicker or by the radio frequency interference.     High and Low Voltage Capacitor Panel Application : For Improving Lagging Power Factor of peak loads Systems   Specification : • Multistage controller• Auto/manual controller• P.F. Closer to unity/Targeted• Thyristor/Contractor Switched• Zero voltage switching as per controller• Suitable for variable load.

• Parameter: :
• Rating: Mains Supply
• :: Up to 480V AC 3 Phase, 50Hz
• Output: :
• Up to 435V AC 3 Phase, 50Hz: Capacity
• :: 20Amp (Max)

Three Phase Voltage Correction/Protection Unit   High voltage trip feature protects your machine from high input voltages. This unit will make your machine work/run at High input voltage up to 270V. And if input voltage goes above 270V then High Voltage trip circuitry will turn off the output and protect your machine from high voltage. If you connect your welding machine directly to input without this protector, the high input voltage will damage your machine. Power ON time delays of 10sec suppresses high voltage transients and power surges for safety of your machine. Voltmeter for output voltage indication. Indication for Input supply. Indication for Power ON Time Delay. Indication for High Voltage Trip. It makes user easy to carry or move welding machine with protector to any place.  

• Material: MS
• Application: For Submersible Pump Controller
• Phase: Single Phase
• Voltage Rating: 220/240 V
• Automation Grade: Automatic
• Motor Power: 2 HP
• Brand: Super
• Rated Current: 2000 Amp

Electrical Panels, conventional type machine, Electrical Panel

POWER CONTROL CENTERS, Control Panels, switch boards, starters, Switchgear

Control Panel Board, Motor Control Panel, Power Factor Control Panel

Control Panels, Cables, Solar Lanterns, SOLAR PANELS, Switchgears

lt control panels

Draw Out Panel, electrical product, Load Break Switch, Stainless Steel Panel

Surgeon Control Panel, Video Colposcope, Binocular Loupes

Control Panel Boards