Power Panels Dealers in Sangli

Automatic Power Factor Control Panel controls power factor up to unity. Automatic Power Factor Control Panel helps achieve and maintain unity power factor and gain incentives on electrical bills as much as 7%. Typical application of Automatic Power Factor Control Panel is seen in Dairy Plants, Colleges, Hotels, Bazzars, Shopping Malls, Resorts, Sugar Industries, and Spinning Mills etc. Benefits of Automatic Power Factor Control Panel Reduce electricity bills Control maximum demand Maintain good power factor up to unity Avoid penalty and gain maximum 7% incentives on electrical bills Control reactive power

In Most Of The Industries, Due To The Fluctuating Load Conditions, The Power Factor Also Varies Accordingly. Hence It Is Practically Difficult To Maintain A Penalty Free Power Factor With Fixed Compensation Of Capacitors. This Results In Low Power Factor And Leads To Higher Kva Demand And P.F. Penalties. Due To Variable Load Conditions And Cumbersome Manual Switching Of Capacitors The Power Factor Can Not Be Maintained At Desired Levels. As Close Monitoring Of Power Factor Is Required All The Time To Avoid Penalties And To Minimize The KVA Demand, Automatic Power Factor Correction Panels Are The Best Solutions. The Panel Are Manufactured Using Micro Controller Based Control Relay To Control The Capacitor Switching. All The Settings Are Done By Finger Tip Key Pad With Options To Select “FIFO” Of “CYCLIC” Order And Many More. The Panels Are Made Based On Study Of Your Load And Perfect Tuning Is Possible To The Requirement Of Your System. ADVANTAGES • Avoids Power Factor Penalties. • Reduces KVA Demand • Avoids Leading Power Factor. • Avoids Over Excitation Of Generators. • Minimizes Line Losses. • Minimizes Transformer Losses. • Protects Motors, Switchgears From • Improves Voltage Conditions.

For optimum utilization of available power the reactive power consumption should be reduced or nullified i.e. power factor should be unity, hence, most of the Power Distribution companies have policy to penalize the industrial and commercial consumers for not maintaining power factor above certain limit (generally above 0.90 value). However, due to reactive power drawn by capacitive or inductive load in the consumer premises the power factor is either lagging or leading, thus to maintain it within limit i.e. for compensating or supplying required KVAR, the capacitors (in case of lagging PF) or reactors ( in case of leading PF) are connected across the system. For stable load the fixed KVAR compensation is required , while for variable load the KVAR requirement also changes as per the load duration cycle, thus in such case the Automatic Power Factor control Panel is installedElectric Power quality is a term that has captured increasing attention in power engineering in the fresh years. The power quality is mainly depends on the needs of the equipment that is being supplied. Usually the term it refers for maintaining a sinusoidal waveform of bus voltages at rated voltage and frequency. The waveform of electric power at generation stage is purely sinusoidal and free from any distortion. All the Power conversion and ingesting equipment are also designed to function under pure sinusoidal voltage waveforms. However, lots of devices that distorted the supply waveform. These distortions may spread all over the electrical network. In fresh years, there has been an increased use of non-linear loads, which has resulted in an increased fraction of non-sinusoidal currents and voltages in Electric Network. Classification of power quality areas may be made according to the source of the problem such as converters, magnetic circuit non linearity, arc furnace or by the wave shape of the signal such as harmonics, flicker or by the radio frequency interference.     High and Low Voltage Capacitor Panel Application : For Improving Lagging Power Factor of peak loads Systems   Specification : • Multistage controller• Auto/manual controller• P.F. Closer to unity/Targeted• Thyristor/Contractor Switched• Zero voltage switching as per controller• Suitable for variable load.

• Parameter: :
• Rating: Mains Supply
• :: Up to 480V AC 3 Phase, 50Hz
• Output: :
• Up to 435V AC 3 Phase, 50Hz: Capacity
• :: 20Amp (Max)

Three Phase Voltage Correction/Protection Unit   High voltage trip feature protects your machine from high input voltages. This unit will make your machine work/run at High input voltage up to 270V. And if input voltage goes above 270V then High Voltage trip circuitry will turn off the output and protect your machine from high voltage. If you connect your welding machine directly to input without this protector, the high input voltage will damage your machine. Power ON time delays of 10sec suppresses high voltage transients and power surges for safety of your machine. Voltmeter for output voltage indication. Indication for Input supply. Indication for Power ON Time Delay. Indication for High Voltage Trip. It makes user easy to carry or move welding machine with protector to any place.  

high tension control panel, Bus Ducts Installation Services, MCC Panel Board

Cables, Digital, Heavy Duty Capacitors