Back Back
Window Air Conditioning Test Rig
DESCRIPTION: The Window AC test rig is designed and manufactured such that the students can understand construction and working of a window type air conditioner and conduct the trial on it to evaluate performance of the same. The window AC is fixed in a rigid angle frame, with its cover cut half open to reveal the internal parts of the AC. The required pressure and temperature tapings are drawn for measurement of pressures and temperatures at salient points. Energy meter is provided for recording compressor energy consumption. A sling psychomotor is provided for measurement of inlet and outlet Dry-bulb& wet bulb temperature. With the help of manometer, velocity of air and consequently the flow rate of air can be determined. Technical Specifications:
...more
wind tunnel
250,000 Per Piece
Voltage : 230V
Color : Blue
Country of Origin : Made in India
Power : 5 HP
Phase : Three Phase
...more
Whirling Of Shaft Apparatus
50,000 Per Piece
features : 1. unique model on which various nodes can be observed for different shaft size2. on this equipment, various nodes can be observed by changing end conditions.3. easy to demonstrate.4. guards for fixing the nodal positions. introduction :this equipment is used to study the phenomenon of whirling of shafts for different end conduction's. whirling frequency may be also determined by this equipment for various nodes. specification :1) shafts made from steel & of the following nominal dimensions. dimensions mm-in length mm-4.76mm or (3/16)" 900 or (36)6.35mm or (1/4)" 900 or (36)8 mm or (5/16)" 900 or (36)2) drive 'tullo' make single phase ac/dc fractional hp 6000 rpm.3) dimmerstat for controlling of z ampps speed. range of experiments : display of the various modes of whirl for a range of shafts with -a) both ends directionally freeb) one end fixed and the other free.modes of vibration can be studied & the frequency can be measured in each case. experimental procedure :the speed of rotation of shaft can be measured by use of a stroboscope ( not supplied with the unit.) when the shaft is in the second mode of whirl., the strobo may used for accurately determining the nodal position. tachometer cab also be for speed measurement ( not supplied with product.) space requaired : 1) a floor space area of 40 cm x 180 cm is sufficient for this unit.2) weight = 70 kg.it is necessary to change the shafts after each experiment. During whirling the shaft is subjected to permanent deformation. service requaired : 1) ac 220 v., 50 hz. Supply2) hand technometer3) stroboscope * * hand technometer & stroboscope are in the scope of supply but however it can be made available at extra cost on purchasers request. almost care is taken for preparing this literature, but still if there are any mistakes, those may be excused. we reserve our right to change or modify the equipement without notice.
Brand Name : Labline
Finishing : Powder Coated
Driven Type : Electric
Packaging Type : Wooden Box
...more
Water Cooler Test Rig
The apparatus consists of a storage water tank, embraced by evaporator coil of the cooling unit, cooling cycle comprises of a hermetically sealed compressor, air cooled condenser, a capillary tube as expansion device and an evaporator coil. The trainer is designed for the study of features of a Water Cooler Trainer. It has a facility to measure various parameters like temperature at different points, pressure at different points, refrigerant flow rate, etc. Various measurements provided enables students to determine the theoretical and actual COP, power consumption, actual cooling capacity refrigerant flow and compressor volumetric efficiency of compressor. SPECIFICATIONS: 1) Cooling Cycle- Compressor - Hermetically sealed type, having the capacity of 1/3 ton of refrigeration using R-134 refrigerant. Finned tube type air cooled condenser with forced air flow. Filter cum drier for refrigerant. Capillary expansion device. Evaporator coil embraced on stainless steel water tank,Provided with glass wool insulation. 2) Water drain tap and float operated inlet water tap are provided for water tank with insulated lift door at top.
...more
Vapour Absorption Refrigeration Trainer
DESCRIPTION: “Vapour Absorption Refrigerator” earlier known as “Electrolux” refrigerator is an self contained refrigerator working on absorption technology. In the absence of a compressor or pump, the circulation takes place by density difference. The system is pre-charged with three fluids namely water, ammonia and hydrogen. Hydrogen is used as an “inert gas” and does not undergo any phase change and heat transfer processes. Its purpose is to keep the pressure of the system constant. It uses an electrically operated generator, where, the ammonia vapours dissolved in water are separated and pure ammonia vapours enter the condenser. In the condenser, the high pressure vapours reject its latent heat to the surroundings and get liquefied. The liquid ammonia expands through expansion device where its pressure and temperature is reduced and cold low pressure vapour enters the evaporator where it absorbs heat from the space to be cooled and then vaporized ammonia absorbs in water. This strong solution then enters the generator and the cycle repeats. Technical Specifications:
...more
Universal Vibration Apparatus
Application : Laboratory , Industrial
Country of Origin : Made in India
Universal Governor Apparatus
38,000 Per Piece
Country of Origin : Made in India
Type : DC Motor
Power : 0.5 HP
Phase : Single Phase
Voltage : 220 V
...more
Stefan Boltzmann Apparatus
38,000 Per Piece1
1 Piece (MOQ)
The apparatus is designed to determine the Stefan Boltzmann constant. The apparatusconsists of a hemisphere fixed to a backelite plate. The outer surface of which forms the jacket to heat it. Hot water to heat the hemisphere is obtained from a heater in hot water tank which is fixed above the hemisphere. The copper test disc is introduced at the centre of hemisphere. The temperatures of hemissphere and test disc are measured with the help of thermocouples and temperature indicatior. A times is provided to measure the temperature of disc at the interval of 5 seconds.
Brand Name : Labline
Finishing : Powder Coated
Driven Type : Electric
Shape : Square
Color : Grey
Condition : New
Automatic Grade : Manual
Speciality : Easy To Use
Usage : Laboratory
Certification : ISO 9001:2008
Voltage : 220V
Packaging Type : Carton Box
Weight : 20-30kg
Machine Weight : 100-1000 Kg
Phase : Single Phase
Warranty : 1 Year
Country of Origin : India
Corrosion Resistance : No
...more
Single Stage Air Compressor Test Rig
DISCRIPTION :- The test rig comprises of a Single Stage Air Compressor fitted with an air tank with orifice, pressure gauges and an energy meter to measure the input. A digital Temperature indicator measures the temperatures at various points. The compressor is mounted on air receiver along with the motor, and is provided with air relief valve (safety) and a pressure switch. The unit determines volumetric efficiency and isothermal efficiency at various discharge pressure SPECIFICATIONS :- 1)Single stage, single cylinder air compressor driven by a 1 hp. motor, with receiver and pressure safety valve. 2) Digital multi channel temperature indicator to measure the temp. at various point. 3) Pressure gauge to measure discharge pressure. 4) Energy meter to measure input power 5) Orifice with water manometer to measure quantity of air sucked in. SERVICES REQUIRED : 1) Floor space of 2.5 x 1.5 m 2) 440 V, 15 A, 3 ph. Ac supply with neutral and earthing connection. 3) A hand tachometer. (It can be supplied at extra cost)
...more
Reynolds Apparatus
36,500 Per Piece
Refrigeration Control Display Board
DESCRIPTION: The display board consist nearly all the components used in refrigeration system. The arrangement of parts such that, all the parts are visible and the construction can be easily understood. The components are mounted rigidly on the powder coated steel frame. Nomenclature helps to identify each component. TECHNICAL SPECIFICATIONS:
...more
Pressure Measurement Apparatus
The unit consists of a water flow pipe, in which an orifice is fitted to create the pressure difference. Various pressure measurement devices are fitted to enable the students to have good insight of the devices. Following devices are provided on a vertical board. SPECIFICATIONS1. Pressure gauge.2. Vacuum gauge (not provided with conventional type equipments.)3. U-tube manometer.4. Differential manometer. 5. Single tube manometer. A technical manual accompanies the unit.
...more
Pitot Tube Apparatus
The Unit should consist of Pitot tube for1" pipe line Pipe Line for Pitot tube 1 HP High Head Monoblock. 1 Mtr. height Double Column Differential Manometer Measuring Tank: 500 x 500 x 400 mm Supply Tank :- 1000 x 700 x 300 mm Instruction Manual
...more
Pipe Friction Apparatus
47,200 Per Piece
Material : Mild Steel
Country of Origin : Made in India
Petrol Engine Test Rig
Engine – Automotive petrol engine. Four stroke three Cylinder Four Cylinder, water cooled, developing 15 BHP at 2500 RPM, Provided with battery and self starter.Arrangement to cut off the ignition to conduct Morse test The test rig enables to determine I.H.P.B.H.P., specific fuel consumption, Air fuel ratio Volumetric efficiency and heat balance sheet at different loads and speeds.
...more
orificemeter apparatus
FEATURES :1) Rust proof powder coating to the tank.2) Mercury Manometer for Reading. 3) 0.5 H.P. Motor operation.INTRODUCTION : Venturimeter & Orifice meter is a device used to measure the flow in a pipe line. Venturimeter has converging & diverging section while Orifice meter is made up of thin circular plate & has a hole then a convergent section. DISCRIPTION :- The equipment consist of Venturimeter & Orifice meter fitted in two different pipe lines & connected to a manifold. The tapping on Vanturi & Orifice are connected to a differential manometer. A measuring tank is supplied to measure discharge.
...more
Orifice Meter Apparatus
Venturimeter & Orifice meter is a device used to measure the flow in a pipe line. Venturimeter has converging & diverging section while Orifice meter is made up of thin circular, The equipment consist of Venturimeter & Orifice meter fitted in two different pipe lines & connected to a manifold. The tapping on Vanturi & Orifice are connected to a
...more
Orifice and Mouthpiece Apparatus
47,200 Per Piece
Voltage : 230V
Country of Origin : Made in India
Brand Name : Supersonic
...more
Orifice & Venturi Meter Apparatus
We are offering orifice & venturi meter apparatus. Specification :- 1) sump tank with flow - 1000 mm x 300mm x 400 mm 2) measuring tank - 300 mm x 300 mm x 600 mm 3) mercury manometers (differential) 4) each line provided with flow control value for setting of different flow rates. 5) pressure tubes of different pipe lines are connected to common manometer through cocks. 6) easy to operate and replacement of venturimeter & orifice meter. 7) flow control value at the end of each line assures full running of pipe.
...more
Notch Apparatus
specifications : m. S. Storage tank (channel ) of size 300 mm x 300 mm x 1200 mm length provided with four sets of baffles and sieves for steadying water supply, fixing arrangement for interchangeable notches. baffles for steadying water supply. arrangement for fixing interchangeable notches. supporting stand for the equipment. measuring tank of 600 mm x 600 mm x 300 mm capacity with drain valve & gauge glass. sump tank size 750 mm x 750 mm x 600 mm. set of 2 brass notches: ( as requirement extra provided with extra cost)1)rectangular notch.2) ‘v’ notch.600 range of experiements : 1) to determine co-efficient of discharge (cd) through.a) rectangular notch.b) v notch. service required : 1) water supply arrangement @ 2 to 10 l.p.s.2) suitable drainage arrangement. Floor space : 3m x 1m.
...more
Motorized Gyroscope Apparatus
40,000 Per Piece
1 Piece (MOQ)
features: demonstrates relationship between applied torque & precision rate along with direction of rotation. gyroscopic couple easily verified by an arrangement of weights. precisely balanced rotor. completely portable & suitable for class room demonstration. observe the relationship t = i. W. Wp introduction : now a days gyroscope is a very important tool used for various controls in high technology vehicles.therefore study of gyroscope is of high importance for modern engineering student. description: the motorised gyroscope consists of a disc rotor mounted on a horizontal shaft rotating in the ball bearings of one frame. The rotor shaft is coupled to a motor mounted on a tri union frame having bearings in the yoke frame which is free to rotate about vertical axis. Thus a disc can be rotated about three perpendicular axes. Angular scale and pointer fitted to frame help to measure precession rate. specification: disc rotor – 30 cm dia, 10 mm thick approx. drive – ac/dc single phase motor. Fractional hp 6000 rpm. overall size – 30 cm base diameter, 5 cm height approximate weight – 30 kg. range of experiments : observation of gyroscope behavior( two laws or stability) experimental justification of the equation t= I w wp space required : a bench area of approximately 1 m x 1 m at working height is required to accommodate both the gyroscope and its control unit. service requaired : ac 220 v , 50 hz supply hand technometer. ** hand technometer is not supplied along with the unit but it can be made available at extra cost. please specify clearly while ordering. almost care is taken for preparing this literature, but still if there are any mistakes, those may be excused. we reserve our right to change or modify the equipment without notice.
Condition : New
Voltage : 110V
Type : Motorized Gyroscope
...more
Liquid Thermal Conductivity system
FEATURES : 1. Thermal conductivity of LIQUID can be determined by guarded hot plate method.2. Thermal conductivity can be determined over the mean temperature range of 300C to 800C.3. Ideal for group studies and demonstration.4. Most useful for Research Laboratories.5. Institutions and Oil manufacturers. DESCRIPTION : The apparatus is based on guarded hot plate method. It consists of guarded hot plate and cold plate. a thin horizontal layer of Liquid, under test, is sandwitheched between hot and cold plate. Hot & Guard plates are heated by specially designed electrical heaters. Hot & Cold plates are circular in shape and are made from good conducting materials. A circular trough is formed on cold plate to hod the liquid during testing. A coolant water will circulate through cold plate contunously. Fe-CN thermocouples are used for temperature measurement. The test setup is covered with insulating material bags in enclosure box. SPECIFICATION : 1) Test Setup Hot Plate Assembly. old Plate Assembly.Ring Guard heater Assembly. Top Guard heater Assembly. Coolant water circulation system. Thermocouples (Fe-CN) on Hot plate, cold plate and guard heaters. Insulation bags. Enclosure box with leveling screws. Power supply arrangement for Hot plate & Guard heater. 2) Control Unit Main ON/OFF Switch. Dimmers for Hot plate and Guard heater Power Control of 2 Amp. Capacity each. Voltmeter and Ammeter for Power measurement. Multy hannel Temperature Indicator 0-1000C with high accuracy. Power supply cables. SERVICE REQUIRED : 230 V. A.C. Single phase stabilized power supply.Coolent water supply at the rate of 10 to 15 lit/min. An instruction Manual is supplied with the product. Which describes the equipment and experimental procedure. Almost care is taken for preparing this literature, but still if there are any mistakes, those may be excused. We reserve our right to change or modify the equipement without notice.
...more
Kaplan Turbine Test Rig
Country of Origin : Made In India
Voltage : 230 V
Usage/Application : Industrial and Technical Training
...more
Journal Bearing Apparatus
The apparatus consists of a plain steel shaft encased in a bearing and directly driven by a small electric motor. The bearing is freely supported on the shaft and sealed at the motor end. The bearing contains twelve equispaced pressure tapping around its circumference and four additional ones along its topside and on a vertical radial plane. All are connected by light and flexible plastic tubes to the rear manometer panel so that pressure head of a oil at all sixteen points can be clearly observed at all times.The bearings can be loaded by attaching various weights to the arms supported beneath it. A label is conveniently provided at the front of the apparatus.
...more
Dynamic Balancing Machine
INTRODUCTION: The apparatus enables the students to experimentally balance a rotating mass system and to verify the analytical relations. FEATURES: Independent analysis of Static and Dynamic balancing. Adjustable balance weights with variable moments. Accurate measurement of balance weight position both radially and longitudinally. DESCRIPTION: The apparatus consists of a steel shaft fixed in a rectangular frame. A set of four blocks with a clamping arrangement is provided. For static balancing, each block is individually clamped on shaft and its relative weight is found out using cord and container system in terms of number of steel balls.For dynamic balancing, a moment polygon is drawn using relative weights and angular and axial positions of blocks are determined. The blocks are clamped on shaft is rotated by a motor to check dynamic balance of the system.The system is provided with angular and longitudinal scales and is suspended with chains for dynamic balancing. RANGE OF EXPERIMIENTS: Static balancing of system using steel balls. Dynamic balancing of a simple rotating mass system. Observation of effect of unbalance in a rotating mass system. SPECIFICATION: Drive Motor – F.H.P. Universal motor. Balancing Weights – 4 nos with different sized drills for varying the unbalance. Cord and container system with precision steel balls for relative weight measurement. SERVICE REQUIRED : 1. 230 V.A.C. Single phase electric supply. SPACE REQUIRED : 1. 0.75 m X 0.5 m space area at working height.2. Weight 30 kg.(approximately)
...more
Reviews & Ratings
Write a ReviewBe first to Rate
Rate ThisOpening Hours
Share your Correspondence Details to receive messages from SUPERSONIC ELECTRONICS
Post Free Ad