Lab Incubator Dealers in Solan

• Temperature Range: Ambient +5.0°C to 60.0°C
• Temperature control accuracy: ±0.5°C of set point
• Temperature uniformity: ±0.5°C
• PUF Insulation Density: 40kg/Meter³
• Control type: Time proportionate digital / Microprocessor PID, Auto tune
• Temperature display: 3½ digit LED With motorized fan blower for air circulation Inner full length acrylic door
• Input voltage: 230Volts AC, 50 Hz. To provide Calibration/ Validation certificate

Introduction : National BOD Incubator Construction Of Stainless Steel Sandwich Type 75 MM Thick PUF- filled Body. PUF Insulation Density - 40kg/Meter³, Inner MOC of Chamber - S.S.304/316, Outer MOC of Chamber- S.S. 304 & Wire Meshed type S.S. Trays are Provided (MOC - S.S.304/S.S. 316).Double walled PUF- filled S.S. Door is provided along with Silicon Gasket for air tight sealing. Mechanical lock & Key provision is provided for Door. Master Sensor for temperature is provided for Controlling of chamber. The Control Panel, cooling system, & Air circulation blower are provided with attention of all standard parameter. Mounted on heavy castor wheels for easy movementTechnical Specification : To provide Calibration/ Validation certificate Outer cabinet mild steel powder coated & SS 304 grade dull matt finish. Inner chamber made of stainless steel 316/ 304 grade. Inner chamber stainless steel mirror finish. To provide all documents With DQ, IQ, OQ documentation. Optional Accessories : PLC based system - PLC with HMI 3.7” touch screen Magnetic door lock feature. GSM system - alarms sent to predefined mobile numbers. Controller with printer interface to connect to EPSON Dot matrix line printer. Date, time a n d temperature. Micro processor based PID controller in lieu of above digital temperature. Controller with Auto tune facility Digital timer of 999 minutes with automatic heater cut-off for timed cycle. High temperature safety cut-off with audio/visual alarm.   Temperature Mapping Incubator : Performance qualification with temperature mapping on site. Performance validation test consist of one cycle at any one-temperature point for 2 hours period. This is done to demonstrate the uniformity of temperature within the chamber is acceptable and that the items within chamber receive a uniform temperature condition. Data is collected in printed format from up to six different points within the chamber. Temperature uniformity is considered acceptable if the deviation is less ±1ºC of set temperature. Note : Every National B.O.D. Incubator is validated prior to dispatch at the factory. Those customers who do not require on site mapping may request for Free copy of factory mapping cycle data sheet.

• Power Supply: 220 volt
• Warranty: 1 year
• Temperature: 0-50Deg C
• Use: Labs
• Hertz: 60Hz, 50Hz
• Uniformity: ± 0.5°C at 20°C
• Accuracy: ± 0.2°C at 20°C

We are reliable Manufacturer, Supplier and Exporter of BOD Incubator from Baddi (Himachal Pradesh). Highly versatile and working efficiently, we make available the BOD Incubator that is a low temperature incubator. Our BOD Incubator is demanded by the clients for producing Biochemical Oxygen and for preserving insulin, lever extracts, vaccines and other related chemicals. Construction : Robust Construction. Outer cabinet is made of M.S. Sheet, duly pre treated & finished with epoxy powder coated paint for lasting finish. Inner chamber is made of highly polished stainless steel. It has provision for allowing wide range of shelf positions & spacing. SS trays are also provided. The outer chamber may also be provided of mat finished Stainless Steel. Chamber is duly insulated to minimize heat loss. Two doors are provided. Outer door is insulated and is fitted with magnetic tape for air tight closing for no temperature loss. Door is provided with lock and key. Inner door is made of transparent acrylic/ glass for inspecting the specimens inside chamber, without opening the door and with minimum temperature loss. Temperature Control : The heart of the ESTEEM B.O.D. Incubator is the excellent and reliable solid state temperature controller cum indicator digital display, range from 5oC to 50oC �± 0.5oC. Hermetically sealed, Dan Foss / Emerson Copeland high performance compressor works efficiently to lower the inside chamber temperature. Heating elements are placed in the path of moving air duly insulated from the body. Cooling coils also lie in the air circulation path. Air is circulated by a double shaft self-cooled, blower to keep the uniform temp. Through out the inner chamber. A safety thermostat is provided, which switches off the heaters in the event of failure of the normal temp. control system to protect the specimens from excessive heat. A highly insulated CFC free PUF System is provided to avoid loss of energy. Control Panel : All controls and circuitry are housed at the top of the incubator and therefore protected from spillage. Separate indicator lamps for mains, heating and cooling are fitted. Temperature setting is by finger touch fine and coarse for the user to set any desired temp. A Voltmeter is provided on the panel to read the incoming voltage. Fitted with automatic built in stabilizer. Illumination : Our units are provided with door operated illumination system comprising of fluorescent lights Front Panel : Front panel of our units comprises of on/off switches heating, cooling and mains indicator lamps, temperature controllers and voltmeters Temperature Control : Temperature Sensitivity Spatial Deviation In Temperature Readability Temperature range Temperature Sensor Temperature Controller Display Adjustable alarm limits

• Type: Incubators
• Material: Aluminum, Metal, Mild Steel, Stainless Steel, Steel
• Shape: Rectangular, Square
• Application: Industrial Use, Medical Use
• Color: Black, Blue, Green, Purple, White
• Voltage: 110V, 220V
• Condition: New, Used
• Frequency: 50Hz, 60Hz
• Temperature: 0-50Deg C, 100-150Deg C, 50-100Deg C
• Volume: 100-150ltr, 150-200ltr, 200-250ltr, 250-300ltr, 300-350ltr
• Automation Grade: Fully Automatic, Semi Automatic
• No of Shelves: 2 Shelves, 3 Shelves

Dry Bath Incubator is a microcontroller based instrument designed to control the heating of thermally conducting block. The block is fabricated to fit in 24 test tubes of 12mm dia. The test tubes contact the walls of the block to provide constant precise temperatures to the test tubes contents. The output of the heater is controlled by means of a precision temperature sensor and highly sensitive automatic electronic temperature controller. It is widely used in samples cultivation, preservation and reaction, DNA amplification, pre- degeneration of electrophoresis and solidification. It is used in the clinical, pharmaceutical, chemical, food safety, environment and quality inspection etc.

Medical Waste Shredder With Autoclave, Foreign Body ENT Set, Mortuary Freezer

Wiley Mill, Wet Sieve Shaker, Capillary Tubes, filter holder