Kallpam Trading Nanpura, Surat, Gujarat

The building construction materials are mostly mineral based and they have high porous surface structure which readily absorbs water. The exterior facade get damaged and discolored by rain and atmospheric pollutants. The latest advancement in construction industry is the use of insulating masonry and lightweight blocks and plasters which retain water and moisture. Any absorbed moisture must be able to escape to the atmosphere to protect interiors. To overcome these problems there is need of a coating which must have very high water - vapor permeability, low water absorption, attractive decorative appearance and extreme durability. The Water Dilutable Epoxy Coatings, offered by us, meet all these requirements with mineral like matt finish. Clients can avail from us Water Dilutable Epoxy Coatings of the well-known Hydraepoxy Brand. We make available Water Dilutable Epoxy Coatings at the most competitive prices to the clients. Benefits Water based - nontoxic, nonhazardous nonflammable.Penetrates maximums into the concrete and cement plaster surface, seals porosity and micro crevices.Forms hard, tough and strong film which reduces water permeability.Easily applicable on damp surface and withstand hydrostatic pressure of water.Resistant to water, salt water, soapy water and toilet acid solution.Supplied in off white color and can be over coated by water and solvent based paints. Prevents the growth of microorganisms e.g. fungus Withstands a temperature range of -25c to + 80c. End Uses Water proofing of cement concrete water storage tanks from inside.As a primer on interior / exterior damp walls before painting. Water proofing of bathroom and toilet sunken portions before tiling. Sterile coating on walls of dairies & breweries, pharmaceuticals and food industries. Coating for aquaculture farms and hatcheries. Coating for cement concrete bio-gas plant from inside. Direction For Use Surface Cleaning The surface must be strong and clean, free of dirt, paint oil, sludge, loose cement and plaster, fungus and moss. Clean the surface by wire brushing and emery paper. Remove the dust by broom or compressed air or wipeout with wet cloth. Remove the old paint by scrapping. Mixing Mix part A and part B thoroughly in their individual original containers. Transfer both into a suitable mixing container and mix by spatula or hand to a homogenous paste. Add water slowly, slowly with continuous mixing to get a free flowing, soft brushable paste. Application Apply the mixed material by brush. For filling small joints grooves and cracks use putty. Putty can be prepared by mixing 1kg. HYDRAEPOXY with 2kg. Ordinary Portland cement grade 53 grey or white. if the groove is more than3mm., 2kg. cement and 2 kg. 60/80 mesh silica sand can be mixed with 1 kg of HYDRAEPOXY. For coating of aquaculture farm and hatherles HYDRAEPOXY can be given desired weather durable color shades. Coverage Capacity Coating-First Coat : 50-60sqft./kg.Second coat : 60-70sqft./kg.Putty with cement (3kg.mix) : 40 -50sqft./3kg. Washing Of Tools : Brushes and other tools to be cleaned with water when HYDROEPXY is in undried condition Shelf Life & Storage Instructions : One year from the date of manufacturing if stored in unopened containers at cool & dry place. Packing : 1 kg plastic tins. (Part A & Part B)

Clients can avail from us Ultimate Waterproof Coating which is a thermal insulating, an elastomeric, resilient and waterproof coating. ULTIMATE is a single component, water based high solids, elastomeric acrylic resin based coating. Ultimate Waterproof Coating is an advanced acrylic technology product manufactured by combination of pigments, reinforcing fillers and an Australian thermal non-conductive material. On application, Ultimate Waterproof Coatings form a waterproof elastomeric seal in the form of monolithic uniform membrane, which provides protection from ageing, ultraviolet rays and normal weathering. It reflects heat as well as it does not allow the heat flux transmission. Ultimate Waterproof Coating reduces building maintenance cost as well as saves air conditioning energy up to 25 %. Its performance is more effective than that of the conventional waterproofing and protective products available in the market. Benefits Single component, easily applicable by brush, roller or spray.Adheres strongly to a wide variety of sound substrates such as concrete, metal, modified bitumen wood, polyurethane foam etc.Water vapor transmission decreases maintenance cost.Water seal increases longevity.Ultraviolet light protection maintains aesthetic appearance.Heat - non - conductive property saves air conditioning energy cost up to 25%.Unique non-conductivity (to heat) properly keeps the building warm in cold season and cool in hot season.Prevents growth of moss, fungus and algae. Repels airborne pollutants and dirt that makes the substrate look new for years after application. Lightweight-puts less stress on the building.Nontoxic-safe for the environment and the people, applying it. High reflective-light reflection value of 92 at 700nm.Attractive color shades available, if required. Grades Ultimate HL : zontal surface. Has extra elastomeric resilient property to meet the coefficients of expansion and contraction, wear tear erosion & abrasion resistant.Ultimate VL : ertical surface. Has elastomeric membrane property to meet the movement. End Uses Building roof, terraces and exterior walls, industrial - factory roofing - concrete, asbestos, tin etc. Cold storages, Electronic exchange building roofs, hospital buildings, etc. Direction For Use Surface Cleaning Surface preparation is very important to get the best result and to avoid failure. The substrate must be sound enough, clean and free of dirt, grease, oil, sludge, moss, blistered cement coating, loose plaster etc. Thoroughly wire brush the surface to remove saturated dirt and lose particles. Wash the surface to remove dust. Allow the surface to dry completely. Sealer / Primer Coat The concrete or cementitious substrates are highly porous. It is necessary to make the substrate less Absorptive so that the top coats film thickness remains same. Krishna SEALER is highly elastomeric acrylic emulsion polymer without filled system has extra ordinary penetrating power which seals the porosity. Micro crevices of the substrate. It provides strong adhesion to the substrate and top coating. Due to non-filled system it overcomes the problem of linear stress and strain created in the substrate. Apply one coat of SEALER as a primer coat by brush. Apply the top coat after one hour but within four hours of drying of SEALER coat. Application Seal the cracks of parapet wall and roof substrate by creating a groove of 3mm size, with acrylic sealant. Allow the sealant to dry for 24 hours before applying a sealer / primer. Mixing Mix the content of pack in its original container by stirring with the help of a wooden stick to a uniform, homogenous free flowing paste consistency. Apply the first coat of Ultimate by brush or roller generously. Allow the coating to dry for attest 3 hours before applying second coat. Minimum two coats are recommended. If required, additional coat may be applied. Allow the coating to dry / cure on its own, external curing is not required. Cleaning : Tools and equipment to be cleaned with water immediately after the use. Storage & Shelf Life : Store the material in cool dry place. Shelf life of the unopened container is one year from the date of manufacture. Packing : 1, 4, 20 Liter packs Precaution Do not apply on wet or damp substrate.Do not apply in rain.Do not dilute more than 20% with water.

The building construction materials are mostly mineral based and they have high porous surface structure which readily absorbs water, the exterior facade get damaged and discolored by rain and atmospheric pollutants. The latest advancement in construction industry is the use of insulating masonry and lightweight blocks and plasters which retains water and moisture. Any absorbed moisture must be able to escape to the atmosphere to protect interiors. To overcome these problems there is need of a coating which must have very high water - vapor permeability, low water absorption, attractive decorative appearance and extreme durability. ACRYSIL – the Silicone Resin Emulsion Paint meets all these requirements with mineral like matt finish. The quality Acrysil Silicone Resin Emulsion Paint that we offer is economically priced. Benefits Ready to use Brushable, roller and sprayableAttractive color shades. Excellent water repellency - there is no swelling, flaking or darkening of the finish even after heavy rain and water pressure. High permeability to water vapor and carbon dioxide - open pored surface property ensure a controlled water and gas equilibrium. There is also no effect on thermal conductivity or insulation or carbonation. Very good resistance to weathering, industrial emissions and microbial attack - the surface remains permanently dry. Paintability - because of chalky matt texture, can be easily painted. Solvent free - water born excellent environmental compatible. No dirt pickup No fire hazards. End Uses ACRYSIL is an attractive and protective duel function coating that lasts for more than a decade. It is recommended for old as well as newly built residential, municipal, industrial, conservational & repair of historic buildings. Direction For Use Surface Preparation The surface shall be free of dirt, dust and earlier paint. Thoroughly clean the surface. Any repairing of plaster is required must be carried out prior to application of ACRYSIL. No primer is required, because silicone itself bonds strongly to mineral materials. Do not apply on existing oil paints or non - permeable coating like epoxies or polyurethanes. Wash the surface if possible to open the pores for better performance. Mixing : For priming coat dilute the paint 25 - 30 % by volume with clean water, mix thoroughly to a uniform liquid and apply by good quality brush. Application : For top coats dilute the paint 15 - 20 % by volume with water and apply by good quality brush or roller. Two coats are required for better hiding and protection. Cleaning : Tools can be cleaned with water immediately after use. Storage & Shelf Life : Store the ACRYSIL at cool and dry place away, from sun heat in original sealed containers. Shelf life is six months from the date of manufacture. Packing : 1, 4, 20 liters plastic or metal tins

Clients can avail from us premium Performance Protective Coatings available under the brand name Multi Crete. Performance Protective Coating (MULTI CREATE) is a two component hydraulic binder based product which is very effective for solving sealing problems on porous substrates. Performance Protective Coating is composed of a "Powder" consisting of hydraulic binder, chemical inert aggregates and waterproofing additives as one part and Resin Emulsion as the second part. The two components are mixed together to obtain a plasticized cement rendering. Once applied, Performance Protective Coatings constitute perfectly leak tight coating resistant to strong water pressure. Performance Protective Coatings work even against the normal negative pressure. The cured coating has the appearance of white, slightly rough rendering. Benefits Reacts in contact with water by crystallization.Bonds strongly to most of the building materials.Can be applied on a damp substrate.Forms micro porous coating which allows breathing of the substrate.Can be applied both indoor-outdoors, horizontal vertical surfaces in uniform thickness. Unaffected by UV light.Does not corrode reinforcing steel.Resists high positive water pressure and normal negative water pressure. Acts by perfectly plugging pores in concrete and masonry. Highly durable even in continuous contact with water. Resistant to water, dilute acid and alkali solutions.Non - dangerous and odorless.Resistant to fungus and microrganism growth. End Uses MULTICRETE is used as a protective performing coating in building - terraces, toilets & bathroom basements. It also acts as protection against corrosion and salt. It is used for sealing under positive water pressures in water reservoirs, water tanks, built up pits of all kinds, agricultural silos, swimming pools, sea water pools etc. Direction For Use Surface Preparation: Surface preparation is very important to get the best results and to avoid failure. The substrate must be clean and free of dirt, grease, sludge, fungus, cement coating blistered and loose plaster etc. Moisture is necessary for the effectiveness of MULTICRETE, therefore the substrate must be dampened with water, However, streaming water must be diverted by creating drains.Do not apply in rain. Before application of MULTI CRETE, seal the crack with any suitable sealant.Sealer / Primer Coat The concrete or cementitious substrates are highly porous. It is necessary to make the substrate less absorptive so that the top coats film thickness remains same. Krishna SEALER is highly elastomeric acrylic emulsion polymer without filled system has extra ordinary penetrating power which seals the porosity. Microcrevices of the substrate. It provides strong adhesion to the substrate and top coating. Due to non-filled system it overcomes the problem of linear stress and strain created in the substrate. Apply one coat of SEALER as a primer coat by brush. Apply the topcoat after one hour but within four hours of drying of SEALER coat. MixingAdd the powder (part 1) in to the liquid (part II) and mix manually until a homogenous semi - liquid without lumps, is obtained. The consistency of the mixture should be enable to give a good and smooth application by brush. ApplicationApply the first coat of MULTICRETE generously in order to plug the pores and shrinkage cavities. Within 24 hours, dampen the surface and then apply the second coat. Apply a third coat in the same way, if necessary. Moisten or wet the surface frequently for three to four days. Cleaning : Tools and equipments to be cleaned with water. Storage & Shelf Life : Store in cool dry place. Shelf life of the unmixed material is one year from the date of manufacture. Packing : 10, 20, 70 kgs duel packs. Precaution Do not apply over hot or dry substrate.Do not apply in rain.

We offer Injection Grout which is a cementitious, high flow, expansive, non-shrink injection Grout. The Injection Grout is made available the popular brand Keminject - K5. Injection Grout (KEMINJECT-K5) is single component cement based expansive grout. Injection Grout is a very fine powder material when mixed with water exhibit flow like water and on curing instead of shrinkage shows positive expansion. The non-shrink characteristic makes it suitable for injection grouting of concrete structures such as buildings, bridges, dams, tunnels etc. On curing for 28 days it equals the strength of M-40 concrete. Benefits i>Single component, easily miscible with water.Very low viscosity after mixing with water helps in penetration of micro cracks of the concrete.Bonds strongly to old and new concrete internally.Provides 100% filling of cracks and pores.Expands on curing by the way of duel shrinkage compensation.Strength is much higher than the neat cement paste.Not only fills/seals the gaps, cavities and cracks, provides strength to the structure by consolidating it.Provides cent percent water proofing after grouting.Arrest incoming & outgoing water.Color - same as cement.Non toxic, non hazardous. End Uses: Injection grouting of Building structures - roof, basement, water tank, swimming pool, toilet, bathroom etc. Bridges, dams & tunnels Direction For Use Preparation For Injection Grouting Drill hole on the crack at every one meter in down direction, of the size depends on grouting nozzle size. The depth of the hole shall depend on thickness of the structural part. Clean the dust by air and then by water. Fix the proper size nozzle by using fast setting cement and / or epoxy sealant to cure for at least 24 hours before grouting. Mixing Take clean water as per the w/p ratio into a plastic container (50 liter size). Start adding grout powder with continuous stirring to homogenous free-flowing thin slurry. Grouting Start injecting the mixed slurry by using grouting pump at a pressure of 3-5 kg /cm2 till the material starts oozing out through next nozzles. Remove the grouting connection, close to nozzle. Start injecting through next nozzle. Continue the same process. Cleaning: Clean the tools and equipments with clean water immediately after use. Storage & Shelf Life: Shelf life is six months when stored in original packing at a cool & dry place away from moisture & water. Packing : 5, 25 hassein polythene lined bags. Precautions: Do not dilute more than the recommended w/p ratio.

We offer Duraflex Waterproof Coatings that are aesthetic, as well as water and weatherproof, durable coatings. The Duraflex Waterproof Coatings are far better than plastic emulsion paints, which are in use for aesthetic look on interior as well as on exterior. Duraflex Waterproof Coatings that we deal in are protective, dust repellent and resistant to growth of microorganisms. Duraflex Waterproof Coating is a single component emulsion coating based on specially formulated emulsion polymer, inert fillers, UV durable lightfast color pigments and many other additives. Benefits Single component, suitable for application by brush or rollerAdheres strongly to a wide varieties of sound substrates such as cementitious, wooden, metals & tones etcBreathable, allows water vapor transmission hence decreases maintenance cost. Dust repellent, no adherence of dust to the coating and it can be easily cleaned. Resilient- it is so flexible with recovery properties so that it bridges the cracks due to changes in environmentWater seal increases longevity.Ultraviolet resistance maintains aesthetic appearance.Prevents growth of algae, fungus and moss.Repels airborne pollutants and dirt that makes the substrate look new for years after application. Non-toxic, safe for the environment and the people applying it. Attractive color shades available, if requiredCoverage depends on the roughness and porosity of the surface End Uses : Building facades from interior and exterior, sloppy roofs, manglory tiles, stone cladding, asbestos sheets, mosaic tiles, and wooden substrates. Direction For Use Surface Preparation Surface preparation is very important to get the best results and avoid failure. The surface must be sound enough, clean, free of dirt, oil, grease, sludge, moss, blistered cement coating, loose plaster etc. Thoroughly wire brushes the surface to remove saturated dirt and loose particles. Wash the substrate to remove dust. Sealer / Primer Coat The concrete or cementitious substrates are highly porous. It is necessary to make the substrate less absorptive so that the top coats film thickness remains same. Krishna SEALER is highly elastomeric acrylic emulsion polymer without filled system has extraordinary penetrating power which seals the porosity. Microcrevices of the substrate. It provides strong adhesion to the substrate and top coating. Due to non-filled system it overcomes the problem of linear stress and strain created in the substrate. Apply one coat of SEALER as a primer coat by brush. Apply the topcoat after one hour but within four hours of drying Application Mix the paint in the individual original container thoroughly to a uniform shade and consistency. Then dilute the required quantity with recommended dilutation ratio with water, to a homogenous solution. Consume the entire diluted paint at one stroke. Allow the coating to dry for at least 5 to 6 hours before applying successive coats. Cleaning : Tools and equipment to be easily cleaned with water immediately after use. Storage & Shelf Life : Store the material in a cool and dry place. Packing : 1,4, 20.Lts. packs. Precaution Do not apply in rain.Do not over dilute with water.

Clients can avail from us Cementitious Grout that is non-shrink, expansive, high early strength, and high workability (flow) general purpose cementitious grout. The Cementitious Grout is made available under the brand name Kemgrout – GP. Cementitious Grout (KEMGROUT – GP), offered by us, is a nonmetallic, cement based grout with good (workability flow) and positive volumetric expansion. Cementitious Grout is chloride and iron free hence no corrosion & loss of cohesive strength due to corrosion by oxidation particles. The high early strength of cured grouts allows the immediate installation & operation of the machine or equipment. The grout sustains the high dynamic and static loads transfer by the running machine & equipment. The grouting height provision of the grout is 110 - 120 mm. Benefits Non metallic - no cohesion loss due to corrosion. Chloride free - no corrosion of steel. Good workability and flow-ensure larger contact. Non-shrink - duel shrinkage compensation - ensures volume stability. High early & ultimate compressive strength. Excellent bond between machinery and foundation. Nontoxic Nonhazardous End Uses Grouting of bolt pockets & base plate of any machine & equipment.Boilers, pump sets, generators, turbines, stanchion bases & motors etc.Grouting of columns in precast constructions. Directions For Use Surface Preparation: The concrete surface including bolt pockets shall be free of oil & greaseThoroughly wire brush the surface to remove dirty & dust. Remove Oil & grease, degreasing with xylene, Toluene or Trichloroethylene solvent. Hack the concrete surface for improvement in bonding.Wash the surface with water till it cleans to a original concrete substrate. Saturate the surface with water prior to grouting.Shuttering / Formwork Provide wooden or steel leak proof formwork to withstand operational stressers. Seal the gaps of formwork and concrete surface with Kemgrout -gp grout in thick mortat consistency by mixing with less quantity of water. Allow it to cure for 3-4 hours before starting of group pouring / placement.Mixing Grout mixer or freefall type concrete mixer is recommended.Selection of the grout / concrete mixer capacity will depend on the volume of mixed grout required. The mixer vessel / pot shall be clean & dry. Charge 80% of mixing water. The water must be clean, cold and chloride free. Start the mixer. Start addition of grout powder slowly & continuously for about a minute. Add 25-30 nos. of 5-10 cm size stones or coarse aggregate (clean & dry) for lumpsfree efficient mixing of grout. Add balance 20% of mixing water and mix for 4-5 minutes. Now the grout is ready for pouring / placement.Placement / Pouring Pour the mixed grout through a 10 cm wire mesh kept on a pouring vessel (200 liter fitted with 2 inch ball value at bottom end of the drum) keep the grout agitating by wooden baffle. make sure that the surface is saturated with water & damp .Excess water if any remove by hand pump or cotton waste. Pour the mixed grout from one side only to avoid air/gap entrapment. Provide 100 mm minimum exposed area (shoulder) of grouts at pouring end and 50 mm on the other end. Cover the grout exposed area by plywood or polyethylene (HDPE) sheet for retrain & evaporation of water. Incase grouting bed height exceeds 110 MM, mixing of 50 % by weight of 5 - 10 mm coarse aggregate (clean & dry) is recommended. Provide atleast 10 - 12 hours gap between two subsequent grouting operations. Grout Quantity Estimation Quantity of powder grout required in kgs. = 2.1 - 2.2 x volume of grouting void in liters.(Consider about 5% in kgs. wastage and other contingencies while calculating the requirement) Cleaning Of Tools & Equipments : Easily cleaned with water immediately after the use. Storage & Shelf Life : Store the material away from moisture, water & cover it by tarpaulin in unopen condition. Shelf life is 6 - 7 months from the date of manufacture Packing: 30 kg woven sack with a plastic liner.