Silicone Sealants Dealers in Pandesara, Surat

We are offering boss 122 description for general purpose applications. Boss 122 rtv silicone sealant is an one part acetoxy cure adhesive sealant that is suitable for general construction sealing and adhesive applications. This product will adhere to clean metal, glass, many types of wood, silicone resins, vulcanized silicone rubber, ceramics and plastic surfaces. A primer may be required for optimum adhesion to some substrates. Cured sealant stays rubbery from -60°f to 400°f. Boss 122 rtv silicone sealants ideally suited for sealing , glass windows, shopfront, aluminium joints, showcases, bus body building and automobiles. Benefits: ease of use, one-part sealant, no mixing required. Good weatherability virtually unaffected by sunlight, rain, ozone, and temperature extremes. Long life reliability, cured sealant stays rubbery from -25 to 110°c without tearing,cracking, drying out, or becoming brittle. Wide temperature gunnability can be applied in any season. Typical properties uncured specific gravity 0.97±2 colors clear, white, black sagslump nil tack-free time 10-15 min curetime at 75°f (24°c) and 50% rh (38¢ thickness) 24 hours extrusion rate 275 gmin cured physical elongation >400% durometer hardness, shore a, points 17 tensile strength, mpa 1.8 dynamic movement capability cycled at 18' hr.,18min.% ± 25 silicone sealant, high flow silicone sealant, ge sealant marine silicone, drum pump silicone sealant,,black silicone sealant waterproof, silicone sealant specialists, anabond 666, silicone glazing sealant, food grade silicone sealant, silicone sealant specialties, silicone sealant drying time, structural silicone sealant, silicone rubber sealant, silicone sealant for fiberglass, aquarium silicone sealant, silicone boat sealant, flexible sanitary silicone sealant, high temp red rtv silicone sealant, silicone sealant applicator tool, silicone joint sealant.

• Packaging Size: 600ml
• Surface of Application: Wood, STEEL, Glass, Ceramic, Plastic
• Form: PASTE
• Brand: 3M
• Brand Preference: 3M
• Grade Standard: Industrial Grade, Chemical Grade
• Application Industry: Weatherproofing, Construction, Joint filling
• Features: Water Resistant, Moisture Resistant, Impact Resistant
• Chemical Resistance: Acids, Water
• Gap Fill: UPTO 25MM
• Appearance: SOFT PASTE
• Skin Over Time: 2HRS
• Curing Time: 2MM PER 24 HRS
• Is It Eco Friendly: Yes
• Shelf Life: 6MONTH

We are offering silicone sealant. Silpruf® highly flexible building silicone sealant product description silpruf® is a one part, neutral cure, low modulus silicone sealant. After application, the sealant reacts with atmospheric moisture at room temperature to form a highly elastic rubber seal for building joints and glazing. It is unaffected by weathering conditions such as sunlight, uv radiation, rain, and temperature extremes. This excellent weather ability and its high movement accommodation enables the sealant to perform even after many years of exposure. Silpruf® silicone sealant may be used to seal assemblies of masonry, concrete, metals, plastics, wood and other common construction materials. Silpruf® is specially designed for use in butt joints or lap shear joints in weather sealing and glazing applications subjected to movement. The low modulus characteristic reduces strain on the substrate surface and the elastomeric quality allows excellent recovery from extension and compression cycling. key performance properties • one component, ready to use product • capability to cure at room temperature and ambient humidity conditions • primerless adhesion to most common building materials such as: masonry, concrete, treated wood, metals, most plastics and glazed surfaces. • excellent uv, ozone and chemical resistance typical applications • expansion joint sealing of precast concrete, brickwork, stone, granite, etc. • weather sealing • glazing systems : glass, polycarbonate, acrylics (plexiglass and perspex) and upvc • in factory sealing applications where a low odour is required limitaions silpruf® should not be applied to : • areas where abrasion or physical abuse is encountered in horizontal joints • locations subjected to continuous water immersion • unprepared or wet surfaces • concrete surfaces which contain residual oils or other bond breaking contaminants. typical product data unsured properties form paste color white/black/grey specific gravity 1.4 application rate, g/min 150 tooling time, min 30 tack free time, hours 9 full cure, days 10-14 (depending on temp., rh, and bead thickness) application temperature, “c -30 to +60 cured properties hardness, shore a 20 tensile strength, mpa 1.6 elongation at break, % 700 movement accommodation 50% elastic recovery >95% temperature resistance, 0c -50 to +100 specifications typical product data values should not be used as specifications. Assistance and recommendations are available by contacting ge bayer silicones india (gebsi). instructions for use expansion joint design silpruf® silicone sealant should be no thicker than 10mm and no thinner than 6mm. The width to depth recommendations are given below: width (mm) depth (mm) running meters per cartridge* 12 6 4.17 20 10 1.50 25 10 1.20 30 10 1.00 40 10 0.75 50 10 0.60 *300 ml cartridge joint filler (backup) materials the recommended joint filler materials are flexible polyurethane or polyethylene foam rod. If the joint is too shallow to allow foam rod, use a polyethylene tape. The depth of the silpruf® silicone sealant bead is regulated by the depth of the back up material. The back up rod should be 25% - 50% greater than the width of the joint, thereby extending continuous pressure against the joint walls. surface preparation clean all concrete, masonry and stone joints of all contaminants and impurities. Concrete with release agents or water repellents on the surface, loose gravel, old sealants and other surface treatments and protective coatings are examples of materials which must be removed from the joint surfaces to obtain proper sealant adhesion. The substrates should be cleaned where necessary by grinding, blast cleaning (sand or water), mechanical abrading or combination of these methods to provide a sound, clean surface for sealant application. Dust, loose particles, etc., should be blown out of joints with oil-free compressed air or vaccum cleaned. Clean all metal, glass and plastic surfaces by solvents such as isopropyl alcohol (ipa), methyl ethyl ketone (mek). masking the use of masking tape is recommended to ensure a neat job and to protect adjoining surfaces. Do not allow masking tape to touch clean surfaces to which the silicone sealant is to adhere. Masking tape should be removed immediately after tooling of the sealant is accomplished and before the sealant begins to cure. Method of application install backup foam, masking tapes as specified. Apply silpruf® silicone sealant in a continuous operation, horizontally in one direction and vertically from the bottom to the top of the joint opening. A positive pressure adequate to properly fill and seal the joint width should be employed. Tool and strike the silpruf® silicone sealant with light pressure to spread the material against the back-up material and joint surfaces. A tool with a concave profile is recommended for tooling. In glazing, tool the sealant at the sill so that precipitation and cleaning solutions will not pool. As the silpruf® sealant cures, methyl alcohol vapours are released from the sealant surface. The odour of methyl alcohol will completely disappear when the cure is completed. excess sealant should be cleaned from glass, metal and plastic surface while still uncured, using solvents such as toluene, xylene, naphtha etc. On prrous surfaces, the excess sealant should be allowed to go through the initial cure. It should then be removed by abrasion or other mechanical means. handling and safety these products are manufactured for industrial use only. Uncured product contact irritates eyes. In case of contact with eyes, immediately flush with water for 15 minutes. If irritation persists, get medical attention. Uncured product contact may irritate the skin. To clean from the skin, wipe very thoroughly with a dry cloth or paper towel, before washing with soap and water. By-product released during application and curing may irritate the skin and eyes. packaging and storage silpruf® is available in 300 ml plastic cartridges. Shelf life is 6 months from the date of manufacture, if stored in the original unopened container at normal room temperature. limited warranty gebsi warrants that its product will conform to gebsi specifications at the time of application or use. The product must be stored in accordance with gebsi recommendations, and used or applied before the earliest of (1) the indicated “use before date”, (2) one year from date of purchase, or (3) expiration of such other period or recommended storage time stated in the gebsi product literature. If notified, in writing, of a claim within one month of the product’s use or application, gebsi will, at its option, replace or refund the purchase price of any gebsi product which does not satisfy the foregoing warranty

Dextrin Powder, Inks

Silicone Sealant, spray, clay products

Silicone, NATURAL, ebonite rollers for printing, Packaging

Mild Steel Angles, MS ROUND BAR, MS FLAT BAR, Ms Beam, MS Angles, TMT Bars