Ratchet Set Dealers in Wadhwan, Surendranagar

We have come up with best quality Flexible Shaft With Casings. Casing is generally essential for shaft lengths that go over 8 inches. Casing is also recommended for dirty, dusty, or corrosive environment or when the shafts are run at high speeds in exposed areas which can cause an injury. Flexible Shafts With Casings are used for all kinds of applications. The protective casing keeps the grease in the assembly and doesn’t allow dirt and dust in the rotating shaft. Also, the casing guards against potential injury from the rotating shaft coming into contact with the operator. Flexible Shaft With Casings come with either Oilite Bearing couplings or Ball Bearing. They come with either Ball Bearing or Oilite Bearing couplings. Ball Bearings are typically used for higher speeds and greater loads. Oilite Bearings are used for slower speeds, control applications, and lighter loads. Both Oilite and Ball Bearings Assemblies are available in ten (10) different diameter sizes: .130, .150, .187, .250, .312, .375, .500, .625, .750, and 1.000. 1. Is the application "Bi-directional" or "Uni-directional"? Uni-Directional (Power-FLEX™) These shafts are designed for continuous operation, maximum torque carrying ability, and torsional stiffness in only one direction of rotation: either clockwise or anti-clockwise when viewed from the driving end. The performance of a Uni-directional shaft will fall off dramatically if operated in the opposite direction.Bi-Directional (Steady-FLEX™) These shafts are designed to rotate in both clockwise and anti-clockwise directions. They have more balanced physical properties that allow them to operate in either direction of rotation. 2. What are the torque requirements of your Application? This is the maximum continuous torque (in-lb or N-m) that you will be transmitting through the shaft, will determine the diameter of the shaft required for your application. Start up torques-or short duration peak torques- may safely be 20% higher. If you are measuring your load in Horsepower, you must convert to in-lb using the Torque-Horsepower conversion chart , or use the following formula : Torque = HP x 63,000RPM 3. What Will Be The Minimum Bend Radius During Operation? There is a direct relationship between operating torque and operating radius; as the radius gets smaller the torque capacity of the shaft reduces (indicated in the shaft's Torque vs. Radius Chart) since in tighter bends the wires rub against each other more forcefully increasing the friction, heat, and stress. The minimum radius can be calculated using the following formula : R = x ² + y ²4x 4. Using The Charts To Select Correct Shaft Depending on your application's direction of rotation (see diagram above) and measurement units, click on the appropriate chart to choose the correct Flexible Shaft for your application : Uni-Directional (English Units) Chart Uni-Directional (Metric Units) Chart Bi-Directional (English Units) Chart Bi-Directional (Metric Units) Chart Locate the column with your minimum bend radius in the charts. Start at the top, go down the column until you find the corresponding shaft diameter that is rated for your least torque load. If you click the link below the chart, you can see more specifications for that shaft. 5. Choosing bending stiffness or torsional stiffness If two or more types of shafts of the same diameter meet your torque requirements, it is desirable to choose the shaft with the lowest bending stiffness, since it correlates to lower "torque to rotate" which is a measure of the internal friction in the shaft. If torsional deflection i.e. the shaft twisting under load is a concern, then look at the corresponding torsional stiffness values for the shafts that meet your torque and minimum radius requirements . From these, choose the shaft that best fits your deflection needs. 6. Operating Speed This is the maximum continuous speed in RPM's for a shaft under load. Check the Specification Charts to see that your speed is within the design limits of the shaft. As the speed increases the level of power transmitted can increase as the torque load is reduced proportionally to the increase in the shaft speed. From this you can see that Flexible Shafts like to be run fast so as to reduce torque load. Excessive speed, especially in tight bend radii for extended periods, can cause heat buildup and premature failure. 7. Length Determine the proper length (in inches) of the overall shaft assembly by closely approximating all bends and offsets. Measure the length along the centerline of the shaft. 8. Casing A Flexible Shaft casing is recommended when assembly lengths exceed 8 inches or speeds exceed 50 RPM. Casings serve many purposes such as : Protect the shaft from moisture, dust and dirt while retaining lubricationPrevent injury to the operator by contact with an unprotected rotating shaft at high speedProvide a continuous guide for the enclosed shaft for smooth operationPrevent the shaft from helixing, or looping, during operation under torsional loadsControl the bending of the enclosed shaft by guiding it into more natural and gradual bends while limiting how tight a bend radius it can achieve Ready-Flex® Flexible Shaft with Casing assemblies are available in both Oilite and premium low friction Ball Bearing couplings. Click on the type that fits your requirements and determine which bore diameter you need . Ordering Your Ready-Flex Part numbers are created as shown below. Have your part number ready and call us (732) 752-8300 or email us at support@sswhite.net to order.

We bring forth an exclusive assortment of Auxiliary Shafts. Auxiliary Shafts are available with us in varied dimensions and can be customized as per the demands of the clients. They are powder coated and come with a fine finishing. Auxiliary Shafts are corrosion resistant, abrasion resistant, and durable.

standard flex shaft, Shaft with Fittings, shaft with casing and fittings

auto parts shaft, Bearing Ring, all type of cnc job works

flexible shaft

Axle Shafts, Auto Radiator, Axle Shaft, fork legs, Knock Sensor, Mudguard