Auto Repair Equipment Dealers in Manpada, Thane

We are offering tunnel car wash systems. tepo-auto model no. Tp 901 tunnel car wash machine dimension – l 1100 x w 380 x h 300cm capacity – 550 x 225 x 210cm conveyor length – 1180cm operation area – 1200 x 400cm electricity – 380 v3 phase power – 25kw water supply – 4.5cm 2x water consumption – 90 kgcar wash speed – 45 carhour long brush – 4 x pcs. short brush – 4 x pcs roof brush – 1 x pcs. dry blower – 1 set

We are offering automatic car wash machine. the automatic wash process involves a tunnel with an array of equipment to take care of different parts of a car for absolute cleaning with the help of the conveyor belt system. It includes soft foam brushes, high pressure water jets, under chassis wash, conditioners, soap, wax and polishing ingredients and an air dryer, which gives you a better and a shinning car in few minutes.

• Name: bevelling machine
• Product Name: pipe 8
• Usage: header

pipe 8

• Material: SS
• Brand: Microtech
• Max Flow Rate: 100 LPM
• Usage/Application: Industrial
• Power Source: Electric
• Automation Grade: Semi-Automatic
• Motor Horsepower: 10 HP
• Phase: Three Phase
• Discharge Pressure: 1000 PSI
• Frequency: 50 Hz

We offer entire range of power packs for all types of industries.

The power pack is used as a power source for VCB panels in substations where station battery supply is not available. Power Pack gets charged from line connected PT (burden 200VA). It can supply DC connected loads for operating Closetrip coils and other essential loads such as auxillary supply to protection relays etc. Types : 1)Power pack with Battery Back up

• PRESSURE: UPTO 400 BAR
• FLOW RATE: UPTO 500 LPM
• INPUT POWER / MOTOR: UPTO 60 HP
• OIL RESERVOIR / TANK: UPTO 3000 LITERS
• MOTOR – PUMP MOUNTING: UPTO 20 HP – FLANGE MOUNTING ABOVE 20 HP FOOT MOUNTING
• ACCESSORIES: STD.

FEATURE Tank • Tanks are fabricated from mild steel or Stainless Steel and also from Die Cast Aluminium • Tanks are Designed with sufficient thickness to ensure strength and rigidity and Minimum weld joints • Tank Top Plate is Mild Steel, Stainless Steel or Aluminium of sufficient thickness to ensure rigid support to the whole assembly • All joints like top plate assembly to tank, pipe entries from top plate etc. are sealed using suitable elastomer • Manhole covers are provided in front of the tank to facilitate cleaning and maintenance • Baffle Plate is provided inside the tank to isolate pump suction from turbulence of return line • Following standard accessories are provided : ·         »  Oil collection tray on the top in periphery   ·         »  Drain Valve ·         »  Air breather ·         »  Oil level Gauge ·         »  Inspection Cover • Following Optional accessories are provided : ·         »  Oil Level Switch   ·         »  Temperature Gauge ·         »  Temperature Sensor, Digital Temperature Switch ·         »  Flow Meter and Flow Switch ·         »  Electrical Terminal Box • Mild Steel Tanks go through a 7 tank cleaning process after which they are Phosphated and powder coated Tubing • Cold Drawn seamless tubes as per DIN2391 are used for piping • Ermetto bite type ferrule fittings are used for low pressures and weld-on-nipple or SAE flanges are used for high pressures • Tubes are suitably for oil velocity and pressure • All pipes are well supported using suitable clamps aesthetically laid out. • All pipes are pickled, Zink Plated and cleaned with kerosene before assembly • Hoses are used at locations prone to vibrations. Motor – Pump Unit • The unit is either mounted vertically with pump immersed inside the tank for positive suction and low noise level or horizontally for ease of replacement as per choice • Generally 15HP and above installations are Horizontal and on anti – vibration pads and a common plates • Large pump-motor assemblies are also mounted at the side of the tank for positive suction. They are provided with isolation ball valves, flexible bellows • The units are coupled with bell housing and flexible drive couplings • Location Markers are provided for ease of re-assembly   Hydraulic System • System is design for the operating logic with multiple flow and pressure controls as desired. • System is Design with adequate care to ascertain the right sizing and selection of component taking into account the application and duty cycle • Tank is sized to take care of oil level fluctuation and heat dissipation • Systems are designed with energy conservation with the help of high – low circuits, accumulators and variable delivery pumps • Systems are designed to start on “No Load” and Idle running with Venting Fecility. • Systems are designed with Pilot Check valves in Pressure holding circuits, Reducing valves for separate Low Pressure setting, Sequence valves and Pressure Switches for Sequencing circuits, Pressure Compensated Flow control valves for precise speed controls, Counter Balance valves for falling load support, Catridge valves for high flows and smooth operation, Pressure Switches, Pressure Transducers and Hose Burst valves for Safety as per the requirement of applications • Systems are also designed for Closed Loop applications with Proportional valves for high accuracy and automation controls. Systems are also designed with Hydro – Static Drives • Systems are Manifolded to a large extent for following adventages ·         »  Compact Construction   ·         »  Reduction of tubing and number of leakage points ·         »  Improve the System stiffness and Performance ·         »  Facilitate maintenance • Systems are provided with good quality pressure guages with isolator for safety. In addition, extra guage points also provided with minimess coupling to fecilitate maintenance   System is Designed using all standard makes such as Yuken, Vickers, Denison, Bosch – Rexroth, parker, Dowty, Siemens, Bharat Bijlee, Hydroline, Bhagwati, stauff, Waree, Wika, GIC, Shridhan, etc. • All Fasteners used in the system are 8.8 class or bette

The Pumps are designed and manufactured indigenously under strict quality control and also supported by a prompt after sales services. The Pump units are complete with Prime Mover (Electric Motor Diesel or Gas Engine), Speed Reduces (Pulley drive Gear Box), Control Panel, Standard accessories like relief valve, pressure gauge and regulating valves. Mountings either on Base plate Oil field Skid, or Trailers depending on customer requirements.

automotive dash board instruments, Electronic Hour Meter

We are Offering Base Jack.size :1. Pipe Od 38 Mm2. Pipe Od 34 Mm3. Solid Dia 32 Mmbase Size 150x150x6 (mm)

Wheel Balancer, garage equipments, lpg cng kits, Plasma Cutter, post lifts

Car Washer, car glass repairing services, Car Repair services

Wheel Aligner, Car Audio System, Car Parts and Accessories, car seats

Engineering Equipment, Engineering Goods

Adjustable Base Jack, Single Wheel Barrows, double wheel barrows

Hydraulic Power Packs, Cable Cutters, Crimping Tools, hydraulic shears

Engineering Equipment, Ferrous Castings, hydraulic component, Pipe Fittings

Engineering Equipment, steel plant products

Engineering Equipment, Carbon Fiber Wrap, Decorative Paints

Engineering Equipment

car lifts, Lifting Equipment

Engineering Equipment

Engineering Equipment, Engineering Products, Engineering Goods