Band Heaters Dealers in Thane

• Temperature: 250° C
• Length range: 25mm to 500mm
• Specific watt density: 3.5 W/cm2

Mica band heater, Mica Band Heaters are constructed by winding a nickel-chrome resistance ribbon around mica insulation and encapsulated in a stainless steel sheath. It is then formed to the desired diameter for installation over a dies, barrels and nozzles. They are available in an extensive variety of sizes and shapes with options for holes, notches and cut-outs. A number of threaded terminals, wire lead options and terminal boxes offer great flexibility for field wiring. Heater Constructions One Piece Construction: To be used when a heater can be slipped over a barrel without having to expand the heater extensively. Two Pieces / Multiple Segment Construction: Two piece or multiple segment bands make installation far more convenient and are recommended for applications over a 14" diameter. Spring loaded clamping is recommended. Ensure Heater ID same as OD of cylinder/nozzle Eliminate contamination of oil, plastic, dirt etc on cylinder surface to avoid carbonizing & shortening heater life Secure firmly to avoid Air gap and also to compensate for normal expansion, re-tighten periodically Maintain temperature controls & accessories in good working condition to avoid over heating condition Protects leads from abrasion Avoid process material leakage to terminal

Elstein HTS High Temperature Heaters are ceramic infrared panel heaters, which can be used for operating temperatures up to 900 °C and surface ratings up to 64 kW/ m².HTS series heaters are produced using a hollow-casting ceramic process and are filled with thermal insulation material. This improves the radiant power output to the material to be heated.Furthermore, there is a significant reduction in heat dissipated in the wiring space, so that additional insulation of the heating area is usually not required.Consideration The power can be controlled by using thermocouple heaters with TRD temperature controllers, TSE thyristor switching units and other accessories.IR radiation panels can be assembled using REO reflectors, REF construction sets, EBI and EBF construction elements, BSI and BSH panels as well as mounting sheets MBO.The national safety regulations must be complied with for the respective application, for example, the IEC or EN standard 60519-1, Safety in electrical heating installations.Further information and safety instructions are mentioned in the mounting sheet, which is attached to each heater.

• Condition: New
• Power Source: Electric

band heaters for plastic industry

• Application: Injection Molding Machine, Blow Molding Machine, Extrusion Line
• FEATURES: Saving Energy Up to 30%, Reduce Wattage of Heater, More Uniform Heating, Less Down time increases Productivity, Reduced Preheating time of Machine, Heater cost is recover in shorter time

Spark Enterprise Manufactures and Exports High Quality Mica Band Heaters, Which are Used in a Variety of Industries. Mica Band Heaters Provides Excellent Thermal Conductivity as Well as Conduct Heat Transfer. These Heaters Ensure Smooth Functioning and the Mica Band Heaters have a Long Life and Provide Excellent Heat Transfer.

Coil Type Nozzle Band Heaters are specially designed to prevent the failure of heaters against the leakage of plastic material at nozzle. These heaters gives higher temperature(above 250C) at nozzle point which is required for H.D. Plastics such as Nylon,ABS,Delrin  

APPLICATION For Heating Machines, shapes & tools of plastic processing industry. Technical process – oriented applications   CONSTRUCTION Sheathing – aluminized steel, rust resistant steel, or stainless steel are used with clamps & screws to affix the heater rigidly on cylinder.Heating elements – The element is wound uniformly to eliminate hot spot. For temperature upto 600°C, the heater is also available with helix coiled element insulated with grooved refractories.Spirally wound heating coil insulated with Ceramic Insulators & cover with SS sheet, made as per required sizes with termi-nal connection & fixing clamps CONNECTION In the standard model the connection boxes extend with tangential cable introduction over the total width of the band heater. Shortened connection box seated on a definite axial position is possible under observation of technical features. Construction of the connection boxes, clamping & shutter fittings, perforation & bores in radial as well as axial position is possible, depending upon requirement. Heat Resistant, insulated, metal braided cable of any convenient length. STANDARD SIZES & CAPACITIES Inner dia. - 80 mm to 300 mm Width - 35 mm to 300 mm Supply (Volts) – Any convenient Voltage under the pre condition that it should be technically feasible. Power (Watts) - Any convenient Wattages up to 40 W / Sq. inch.

Band Heaters, Air Heaters, Water Heater, Thermocouples, preheater, Ovens

Ceramic Band Heaters, Nozzle Heaters, Immersion Water Heater, Water Heaters

Band Heater, Electric Water Heaters, Tilting Furnace, nitriding furnace