Cartridge Heaters Dealers in Thane

Anupam's "component heaters" that are used to heat up many different applications. Primarily used in mould, these heaters fit snug inside a cavity and helps heat solids by reaching high temperatures. Cartridge heaters have the versatility of being able to carry thermocouple inside to help control temperatures of the heater more accurately. Various diameters allow for it to be used in any cavity and can be custom designed with any cold section. Lead wires extend from the end to your controls.   APPLICATION Packaging Machinery Heat Sealing Labeling Machines Hot Stamping Plastic Iinjection Glue guns and Wax pots Shoe Machinery Heating of gases and liquids FEATURES Stainless steel sheath for oxidation resistance. Unique winding design allows faster heating and longer life Fine grain high purity magnesium oxide (MgO) fills any voids around the resistor wire to optimize heat transfer, dielectric strength and life of the heater. Resistor wire is joined to the leads by placing each end into nickel chromium which, upon crimping, affords a positive and consistent junction.

Our clients can avail from us quality Cartridge Type Heaters that are made of SS 304 metal sheath and are filled with thermally conductive magnesium oxide (MgO). This ensures maximum thermal conductivity, high electrical resistance and better life. These heaters come in parallel coil design, which make it unique. The parallel coils of low watt density are utilized for making up the rated wattage, which results in uniform cartridge heating and eliminates the chances of total burn out. The cartridges are always factory sealed & tamper proof, and these cartridges can easily be replaced online without removing the heater body or taking a shutdown. We offer these heaters in two models - horizontal & vertical.

• Power Source: Electric
• Application: Industrial Use

High watt density split sheathed cartridge heaters uses less power, runs more efficiently and survives more that of cylindrical type conventional cartridge heaters. Due tornits elongation capability it clutches the mould when energized leaving no air gap and contractsrnwhen it cools down parting the following advantage.  maximizes heat transferrn easy maintenancern reduces the cost of operation

cartridge heater is manufactured in ss, brass pipes with high purity mgo (magnesium oxide powder),high quality in chrome wire.cartridge heater is inserted into close fit hole of dies mould or plates. cartridge heater are manufactured in any diameter and length.mgo powder insulation assures high electric strength and fast heat transfer and low oxidation of the resistance wire. it is used to heat rubber molding dies, hot plates, plastic injection moulds, sealing jaws of packaging & pharmaceutical machines. cartridge heater with built in thermocouple temperature sensors for runner less mould are available.   application : for die heating of plastic, rubber & packing machines in ss, brass tuhes. .

Cartridge heaters are most frequently used for heating metal parts by insertion into drilled holes. The ‘D’ heater is designed especially for platen, die or mould commercial heating applications where the holes are poorly drilled or worn through age. Independent expansion of each section of the when energized, creates intimate contact with the wall of the hole. Split Sheath design Improved conductive heater Easily inserted and removed from long holes Incolloy Sheath for long life at extreme temperatures Compacted to maximum density for excellent element to sheath heat transfer and dielectric strength

Our range of high density cartridge heaters are among the most versatile and widely used cartridge heaters throughout the industry These are valuable for alleviating problems created by high wall densities, high wattage, excessive vibration poor fit or where short heater life is a constant problem. These are also widely used to heat the plastic injection molds, dies hot platens, platens and many more.Below mentioned are its specifications:• Actual Diameter inches -002 (Upto dia 58") a 004 (above 4a %)• Actual Diameter MM-050 (Upto dia 16mm) & 80(above Dia 20mm)• Resistance Tolerance-NEMA standard plus 10 % minus 5 %• Wattage Tolerance-NEMA standard plus 5 % minus 10 %   Application Areas:• Designed for High Watt density• The use of high purity Mgo insulation assures high dielectric strength fast heat transfer efficiency• Swaging increases the high thermal conductivity and uniform heating• Shock and Vibration resistant• Available also with built in thermocouple

LEI™ cartridge heaters provide excellent heat transfer and are normally sheathed in Brass or Stainless Steel tubes. These heaters are designed for push fit into holes of nominal diameters. They are used for heating Dies, Molds, Platens and various other applications demanding localized heating.   LEI™ Cartridge heaters are available in 2 Types: Low and Medium Density Cartridge Heaters. High Density (Swaged) Cartridge Heaters.

Cartridge Heaters, Air Heaters, Water Heater, Thermocouples, preheater

Anupam Electroheat’s Low & Medium Density Cartridge Heater is developed for heating applications not requiring high watt densities and sheath temperatures not exceeding 300°C. These Cartridge Heating Elements are designed in maximum watt densities of 30 to 45 watts per square inch depending on applications. Such a Cartridge Heating Elements of various sheath diameters can be used in any assembly, equipment or machine. The Low & Medium Density Cartridge Heater can be absolutely customized to suit customer’s needs. Such Cartridge Heating Elements can be an economical option for customers not requiring high process temperatures. Cartridge Heating Elements are designed & calibrated perfectly to ensure that optimum conductivity between the resistance coil and the Cartridge Heater is achieved. The Low & Medium Density Cartridge Heater design consists of a helically wound resistance coil made from nickel-chrome wire, evenly stretched and strung through holes in a round ceramic insulator. The element assembly is inserted into a Chrome Nickel Steel. This alloy provides the best combination of physical strength and resistance to heat oxidation up to 450°C. Specially selected grain size and high purity magnesium oxide is used to fill all remaining space inside the ceramic insulator to increase thermal conductivity, dielectric strength, and provide longer operating life of the Cartridge Heater.  

High Density Cartridge Heaters, Ceramic Heater Plate

Cartridge Heaters, Ceramic Band Heaters, Nozzle Heaters

Cartridge Heater, Ceramic Band Heater, Tubular Heater, Coil Heater

Cartridge Heater, CI Bush, round heater

Cartridge Heaters, hot runners, Ceramic Heaters, Sensors

High Density Cartridge Heater, MS Welding Work, Electric Water Heaters

Cartridge Heaters, Ceramic Heaters, Mica Heaters, Tubular Heaters

Cartridge Heaters, Air Heaters, Ceramic Heaters, Industrial Heaters