Civil Engineering Test Equipment Dealers in Thane

Concrete rebound Schmidt hammer (sclerometer) – is a device for strength testing of concrete and other building materials. The most common in the world instrument for measuring the strength of concrete is the Schmidt Hammer. The device is called by the name of the engineer Ernst Schmidt, who invented the construction of the sclerometer.The method of strength testing of concrete with using the Schmidt hammer is based on the impacting the striker on the concrete surface with predetermined (normed) impacting energy and after measuring the height of the striker rebounding. The height of the striker rebounding will be proportional to the strength of concrete. The strength of concrete is determined by the calibration charts which is supplied with the instrument. Concrete Rebound Schmidt Hammer NOVOTEST SH is very ease in operation, has good reliability of design and high measurement accuracy, so that this method is the most common method of measuring the strength of concrete in the world. The strength testing with the Schmidt hammer is correspond with ASTM C 805; ASTM D 5873 (for rock); DIN 1048, p. 2; ENV 206; EN 12 504-2; ISO / DIS 8045. There are several versions of the measuring methods, which are different in impacting energy. The most “powerful” Schmidt hammer is designed to measure the strength of concrete with a thickness of 70-100mm and more, also for the strength testing of massive rocks with impact energy – 2,207J (Nm). This is the base and the most common model of Schmidt hammer, about 90% of the Schmidt hammers in the world have the same impact energy. Average “powerful” Schmidt hammer has the 735J (735 Nm) impacting energy. The impact energy is reduced threefold in compared with the base model. The main application of this instrument is measuring the strength of bricks and concrete products with a wall thickness less than 100 mm and small sizes of sample, also it used for testing the less strength stones and rocks. The least “powerful” Schmidt hammer has 196J (196Nm) impact energy. The main purpose is the strength testing the mortar of brick masonry.  Depending on requerments tasks user always need to select the correct model of Schmidt hammer. All models, independently of impact energy, are devices for non-destructive testing, so that they are not destroying the object of testing. To verify the accuracy of Schmidt hammer, is used a special calibrated anvil. Correctly functioning instrument have to display the certain value when it testing the standard anvil.Advantages Concrete Rebound Schmidt Hammer NOVOTEST SH has 3 modifications with different impacting energy, so that user can test all kinds of concrete and other building materials.

* Sterility Test Unit 47mm Stainless Steel (3 Branch Sterility) 47mm Stainless Steel (6 Branch Sterility) * Oil Free Vacuum Pump suitable for above sterility Model - SAV - 75-S Max.Flow - 45LPM, Vacuum - 27" Hg (680mm)

For immaculate quality Cloud and Pour Point Test Apparatus, you can contact us. We are nonpareil Manufacturer, Supplier and Exporter of Cloud and Pour Point Test Apparatus in Maharashtra, India. The Cloud and Pour Point Test Apparatus we make available has four compartment units with built in digital temperature controller cum indicator. Our Test Apparatus is provided with individual ON/OFF switch and controlling facility for each and every section.

• Material: Plastic, Stainless Steel
• Display Unit: Psi
• Automation Grade: Manual
• Accuracy:  ISO 10648-2
• Test Time: 10 min

We are offering for our valued client’s quality approved Fume Hood. This is designed in accordance with the set industry standards at our end. Offered fume hood can be accessed in varied sizes and dimensions for applications in different industries. Our professionals use the latest technology and optimum quality raw-material for manufacturing this product. In order to meet exact needs of our clients, this can be customized in various Features : » Smooth finish » Unique look » Innovative design   Baffle: Removable plates incorporated into the rear or top of the work chamber to form a plenum between the work chamber and the exhaust duct connection to promote uniform scavenging of fume and the point of discharge. Exhaust System: All exhaust air ductwork, fan and associated equipment installed between the point of connection to the fume hood and the point of discharge. Face Velocity: The velocity of the air passing through the work opening of the fume hood measured in the plane of the sash. Measured in feet per minute (fpm), or litres per second. Make-up Air: Air needed to replace the air exhausted from a room by the fume hood and other ventilation devices. Plenum: A low-velocity chamber used to distribute static pressure (from the fan in the system) throughout its interior. Sash: A transparent safety screen in the work opening of the fume hood, which can be positioned between the operator and the work chamber for protection. The opening can be adjusted vertically to vary the size of the opening and control the face velocity of air into the fume hood.

• Country of Origin: United Kingdom
• Brand Name: Mecmesin

Compressive shear testing is simply the pushing apart of a material sample along a plane parallel to, and between, opposing forces. Typically it is used to test adhesive bonds, where it is the compressive equivalent of a tensile lap shear test, or the internal strength of a material that is designed to bear shear forces. A compressive shear test may be single, where one part is pushed down across another, or double, where a bonded section is pushed out from between those on either side. In the case of a single shear, potentially there are cantilever forces also at work, depending on the thickness and flexibility of the material under test

complete automatic system.
display indicates set and actual vacuum level.
vacuum level can set as per requirement up-to -600 mm hg.
settable retention time, start delay time and vacuum hold time.
automatic release of vacuum pressure.
alarm indicates the test over.
incorporated with inbuilt diaphragm (oil free) vacuum pump.
print facility (parallel interface for dot matrix printer).
20 x 4 alphanumeric informative lcd screen.
4 x 4 matrix self explanatory key board.

• Application: Exhaust
• Brand Name: K=TAg
• Material: Metal
• Finishing: powder coated
• Shape: Rectangular
• Color: As per customer demand
• Condition: New
• Size: 4*2
• Type: Fume Hood
• Country of Origin: India

A Fume Hood or fume cupboard is a type of ventilation device that is designed to limit the user's exposure to hazardous or noxious fumes, vapors or dusts. A fume hood is typically a large piece of equipment enclosing five sides of a work area, the bottom of which is most commonly located at a standing work height.   Fume hoods serve to control exposure to toxic, offensive or flammable vapors, gases and aerosols. Fume hoods are the primary method of exposure control in the laboratory.   Fume Hood cabinet inside Negative pressure, there for control exposure to toxic, offensive or flammable vapors, gases and aerosols.   Two main types exist, ducted and reticulating. The principle is the same for both types: air is drawn in from the front (open) side of the cabinet, and either expelled outside the building or made safe through filtration and fed back into the room.   Fume Hood is available in, SS 304 / SS 316 / SS 316L, CRCA Powder coated.   Unit Description Construction are Stainless Steel Body OR CRCA Powder coated Differential Pressure Gauge Milky White Light Feather Touch Motor Blower Assemblies : 0.5 HP, ~230 V, 1 phase, 50 Hz HAPA Filters (Final Filter) : H13, Efficiency 99.97% down to 0.3µ Exhaust HAPA Filters : H13, Efficiency 99.97% down to 0.3µ Prefilters : EU6, Efficiency 95% down to 5µ Ultra violate Light Hour Meter Sliding Glass Door   Optional Accessories Stainless steel perforated grille for HEPA Filter Filter blocked alarms

• Range: 0 – 10 mm with 0.01 mm

Ring & Ball (Softening Point) Test Apparatus is used for determination of softening point of bituminous materials. Softening point is that temperature at which the specimen under test becomes soft enough to allow a steel ball of specific dimensions to fall a required distance under test conditions.

Fume hoods are laboratory primary safety testing device . A laboratory fume hood is a ventilated enclosure where harmful or toxic fumes or vapors can be handled safely. The purpose of the hood is to capture, contain and remove contaminants, preventing their escape into the laboratory. This is accomplished by drawing contaminants within the hood’s work area away from the operator, so that inhalation and contact are minimized. Airflow into the hood is achieved by an exhaust blower that “pulls” air from the laboratory room into and through the hood and exhaust system. This “pull” at the opening of the hood is measured as face velocity. A baffle, air foil and other aerodynamically designed components control the pattern of air moving into and through the hood. Contaminated air within the hood is then diluted with room air and exhausted through the hood’s duct system to the outside where it can be adequately dispersed at an acceptably low concentration. Our fume hood performs effectively and safely at the face velocity of 100 fpm (or 0.5mtr/sec) at defined sash opening. These laboratory fume hoods consist of standard vertically operated counter balanced toughened glass sash opening. It will have double skinned construction to make it safer. It comprises of electrical components and utilities as per the need of experiment. Basic types of Fume hood -  Constant Air Volume (CAV)  Variable Air Volume (VAV) Fume hood type depend upto function and Construction.  Conventional type Fume Hood  Constant Volume Bypass Air type  Walking type Fume Hood.  Table top type fume hood  Fume Hood with Base cabinet type

• Color: White
• Brand Name: AVI
• Model Name/Number: AVI36564646
• Usage/Application: Industrial
• Type Of Testing Machines: TABLET
• Packaging Type: Box
• Display Type: Digital
• Power Supply: Electric
• Surface Finishing: Colour Coated

• Automation Grade: Manual
• Model Name/Number: 550 / 551
• Brand Name: Taber
• Hardness Scale: Balanced, calibrated scale beam

Products - Digital Friability Apparatus (Single/ Double Drum) Measures Obsession Strength of tablets with programmable timer. Rotation Speed 25rpm ±1, auto & manual mode on 3 digits LED display and it has a 3 digit presentable control.    

• Speed: 25rpm ±1

Measures Obsession Strength of tablets with programmable timer. Rotation Speed 25rpm ±1, auto & manual mode on 3 digits LED display and it has a 3 digit presentable control.

• Power: 230V 10Degree AC,50Hz,10W(Supply)
• Voltage: 230 V
• Temperature: 5-60 deg C
• Display: 4-Digit Seven Segment Bright Red LED
• Vacuum: upto 22 of Hg
• Weight: Upto 13 Kg
• Number Of Stages: Single stage
• Frequency: 50Hz
• Packaging Details: BOX

• Country of Origin: Made in India
• Frequency: 50 Hz
• Brand Name: Pharmintech
• Air flow: Vertical
• Noise Level: 65 dBA
• Light Intensity: >300 lux
• Voltage: 230V AC
• Phase: Single Phase
• Surface Finish: Powder Coated
• Air Velocity: Les than or equal to 0.5m/s

Features > Ideal for checking sealing integrity of blister, strip and pouch packs capped bottles etc.> Extremely compact construction> Very low noise level> Polycarbonate vacuum desiccators sustain vacuum for long time> Stainless steel (GMP) construction> Built in vacuum gauge and isolation valve> 0-5 minutes timer for auto-stop> Vacuum level up to 550 mm of hog Specifications

We are manufacturers and exporters of Slump Cone that finds application in determining the consistency of freshly mixed concrete, where the maximum size of the aggregate does not exceed 38 mm. This equipment consists of one slump cone with handles and foot pieces and ensures hassle free performance at all levels of operations. Technical SpecificationThe slump cone has internal dimensions 20 cm dia at base 10 cm top dia and 30 cm height Foot pieces can be fixed to the clamps on the base plateThe base plate has lifting handle for easy transportationOne graduated steel rod 16 mm dia x 600 mm long, rounded at one end and graduated in mm, is also supplied

• Automation Grade: Semi-Automatic
• Material: Mild Steel
• Usage/Application: Laboratory
• Brand Name: Alfa
• Dial Gauge: 0.01mm x 25mm travel
• Triaxial Cell Diameter: 38mm Soil Specimen
• Loading Frame: 50 kN with 6 different speeds
• Proving Ring: 200 kgf (2 KN) capacity with dial gauge 0.002mm x 5mm with calibration chart

• Size: 10ft, 4ft, 5ft, 6ft, 8ft
• Type: Fume Hood
• Material: Metal, Stainless Steel
• Shape: Rectangular, Square
• Application: Laboratory Use
• Color: Black, Grey, Red, Silver, White
• Condition: New, Used
• Finishing: Non Polished, Polished
• Height: 5ft, 6ft, 7ft, 8ft
• Approx. Price: Air Volume

Determination of the temperature at which a standard indenter penetrates 1mm into the surface of a plastics test specimen under one of the loads specified under uniform rate of heating. Rate of rise of temp. 50 + 50C per hr. 120 + 120C

• Shipping Weight: 4 lbs (1.8kg)

The sample is cast in shouldered rings and heated at a controlled rate under the weight of a steel ball. The softening point is the temperature at which the bitumen disks soften and sag downward a specified distance.

• Material: Mild Steel, Stainless Steel
• Certification: CE Certified, ISO 9001:2008
• Application: Sterility Test
• Color: Brown, Grey, Light White, Off White, Silver, White
• Voltage: 110V, 220V, 380V, 440V
• Condition: New, Used
• Power: 1KV, 2KV, 500W, 750W
• Phase: Double Phase, Single Phase, Triple Phase
• Warranty: 1yrs, 2yrs, 5yrs
• Temperature: 0-50°C, 100-200°C, 200-400°C, 50-100°C
• Vacuum range: 150-300mm, 300-600mm, 600-900mm

Jumble Test Apparatus that is Dimensionally Accurate and is Used for Varied Testing Purposes. the Jumble Test Apparatus that We Deal in is Comparatively Larger Than the Dimensions of the Fuze Because of Which the Fuze Can Freely Jumble in the Metal Box that is Lined with Wood.