Electronic Test Instruments Dealers in Tembhi Naka, Thane

• Display: 16 X 1 Alpha-numeric LCD Display With Backlight
• Models: P-181 or. F-181
• Type of Meter: Insertion Paddle Wheel type Velocity Meter
• Max. % of Solids: 1% of fluid volume, non-abrasive, non-magnetic, <100 micron in dia. & length
• Mounting: Field or, Panel
• Pressure drop: Less than 0.1 bar
• Pipe Line Size: Min. 15 Mm Up to 500 Mm
• Pulses: 4 Pulses each rotation
• Accuracy: +/- 1% of Full Scale if velocity is more than 0.5 m/s
• Repeatability: +/- 0.5%
• Linearity: +/- 2% of full scale
• Enclosure: Weather proof IP 65
• Gland: PO7
• Fitting Material: ABS, SS304 or, SS316
• Fitting Type: Threaded, Flanged, Weld on Adaptor
• Velocity Range: From 0.5 to 5.0 Mps
• Max. Operating Temperature: 60°c for Pp Sensor with Abs Fittings & 100°c for Ss Sensor with Ss Fitting
• Sensor Cable Length: 0.5 mtrs for Field Mounted Meter & 3 mtrs for Panel Mounted Meter
• Paddle: PVDF (Magnetic up to 100°C & Non Magnetic up to 80°C)
• Indicator Housing: Polycarbonate
• O-rings/Pin: Viton / Hastealloy C
• Sensor Rod: PP or, SS316
• Indicator unit dimensions: 110 mm (H) X 110 mm (W) X 150 mm (D)
• Field selectable Units: MPS
• Supply: 230 V AC +/- 15%, 50 Hz
• T Fitting: it is Compulsory with Pp Or, Ss 316 Flow Sensors (selection from Type of T-fittings)

• Resolution: 01 pH 0.1 mV Temp. 0.1 °C
• Calibration: Auto / Manual
• Power: Upto 100 samples
• Display: 16 x 2 alpha numeric LCD display
• Range: 0 to 14 pH 0 to + 1999.9 mV, Temp. 0 to 100°C
• Accuracy: + 0.01 pH + 1 digit mV, Temp + 0.10
• Storage: 230V + 50Hz
• Accessories: pH Electrode, Temperature probe, Electrode Stand, Buffer solution, Dust cover, Manual

As you must know Rain Water Harvesting - is the activity of collection of water. It can be either store for direct use or can be recharged into the ground. As studied above, while dealing in second part of the definition that – “it can be recharged into the ground”. Resistivity test is the key factor. As we know the underground strata broadly it is - soil then Murom layer next is the Hard Murom & then the Basalt or in some cases it is marine clay & basalt.

CX-505 measures pH, redox potential (mV), conductivity, salinity, resistivity, concentration of oxygen dissolved in water in % of saturation or in mg/l, atmospheric pressure and temperature. The measurements made in all measuring functions are of very high accuracy and stability. Unification of the procedures in all measuring functions makes working easier. “HOLD” function to freeze the result on the display. Signalisation of the result stabilisation “READY” with symbol and sound. Possibility of sending to a PC a report of calibration - up to 10 last calibrations. In the pH measuring function: Calibration of the pH electrode: 1 to 5 points. Automatic detection of the buffers’ value entered by the user. Automatic correction of the standard solution value (NIST) along with the temperature changes. Possibility to store characteristics of 3 electrodes makes changing them easily. Automatic evaluation of the electrode’s condition. Depending on the chosen electrode possible measurements in pure water, sewage, pastes, etc. In the redox (mV) measuring function: Precise redox potential measurement (accuracy 0.1mV). Possibility to measure redox potential relatively to the entered or measured reference potential – Vref. Possibility of automatic calculation of the redox reading in relation to the chloride/silver electrode to the hydrogen electrode.   In the conductivity measuring function: Wide measuring range enables measurements in ultra pure water, natural water as well as in very salty solutions. Newly introduced function is the resistivity measurement of the tested liquid. Salinity measurement in NaCl or KCl on the basis of the actual real characteristics. Defining the TDS (Total Dissolved Solids) based on conductivity measurement. 6 sub-ranges switched automatically. In case of measurements of natural water with conductivity from 60 μS/cm to 1 mS/cm the meter enables using non-linear temperature compensation. The parameters of this type of water is determined in norm EN27888:1999 and concerns surface waters, deep water and well water. This solution lowers the measurement error. The measurement accuracy of the ultra pure water with temperature compensation was increased by automatic adjustment of the α coefficient depending on the temperature and kind of trace contaminations. Calibration by entering the constant K of the cell or in standard solutions in 1 to 5 points. Wide range of α coefficient 0 to 10 % / °C chosen depending on the measured solution. Possibility of changing the reference temperature. In set with high accuracy conductivity cell ECF-1. Measuring range 0÷500 mS/cm sufficient for measurements in ultra pure water and high salt concentration samples. Metal electrodes are easy to clean and PVC body protects it against mechanical damage. Possibility of storing constant K of 3 conductivity cells. Automatic conversion of conductivity into salinity in NaCl or KCl on the basis of the actual characteristics and not a constant coefficient, what greatly increases accuracy. In the oxygen measurement function: Galvanic dissolved oxygen sensor. Each of the models equipped with a function of automatic atmospheric pressure measurement with calculation of its influence on the oxygen measurement readout in mg/l. The meter with dissolved oxygen sensor are easy to operate. Calibration of the oxygen sensor in 1 or 2 points. Automatic or manual temperature compensation. Possibility of introducing the salinity value with automatic calculation of its influence on the result of oxygen measurement. The meter automatically counts the influence of salinity measured in the conductivity mode on the oxygen measurement result. Other features: * Automatic or manual temperature compensation. * Internal clock with date. * Internal data-logger enables storing up to 4000 measurements taken as single or in series    with time, temperature and date. * The results and calibration data are stored in non-volatile memory. * Remembers the next calibration date. * USB output for connecting with PC. * The meter meets the GLP requirements.

A cylindrical Main capsule fitted with powerful magnet, which moves up & down alongwith the level rise or fall. This movement will be magnetically coupled with the follower Red indicator outside the chamber which is enclosed in the glass tube.MOC - C.S./S.S. 304/ SS 316/ PP/PVDF/PTFERange - 250 MM - 3000 MMConnection - 100 NB & 150 NB, Flanged typeFloat - SS-304/316 L, Glass, HDPE, PP, PVDF, PTFE ECTFE / HalarcoatedApplication - Suitable for hazardous, expensive, poisonous & flammable liquids. Option : Can be provided with level transmitter & with or without HART-Protocol We are one of the foremost manufacturers and suppliers of a comprehensive assortment of Side & Top Magnetic Level Indicator. Our range is appreciated for higher degree of accuracy, precision & compact design, durability and longer service life.. Side Mounted Magnetic Level Indicator: A cylindrical S. S. float fitted with powerful magnet, which moves up & down alongwith the level rise or fall. This float movement will be magnetically coupled with the follower Red indicator outside the chamber which is enclosed in the glass tube.MOC - C.S./S.S. 304/ SS 316/ PP/PVDF/PTFERange - 250 MM - 3000 MMConnection - 100 NB & 150 NB, Flanged typeFloat - SS-304/316 L, Glass, HDPE, PC PVDF, PTFE ECTFE / HalarcoatedApplication - Suitable for hazardous, expensive, poisonous & flammable liquids.Option - Can be provided with level transmitter with or without HART-Protocol.

Ultrasonic technology (no mechanical moving parts), Accuracy class 2 acc. EN 1434, Manufacturer approval H1 acc. MID (European Measurement Instrument Directive), Energy meter consist of flow part, calculator and temperature sensor, The energy meter shall be calibrated as one unit acc. EN1434, flow sensor for cooling application in IP65 (protected US sensors), max flow rate shall be 2x nominal flow rate (permanent).

• Brand Name: AVI
• Accuracy: 0.5 percentage of full scale
• Voltage: 240 V
• Application: Laboratory
• Power Source: Electric
• Usage/Application: Laboratory
• Material: SS
• Display Type: Digital

• Frequency: 128 Hz
• Measurement Range: Up to 0.1 Ohms
• Accuracy: 2%
• Display: 3½ digit, Low battery indication
• Battery: 12 V 1.5 Ah, rechargeable
• Weight: 1.5 kg
• Dimensions: 225 mm x 150 mm x 75 mm
• Working Temperature: 0 C to 55 C

In order to reduce Broadband and ISDN Line transmission losses, it is essential to check Earth resistance. With this tester we can check earth resistance up to 0.1 ohms. We can also measure soil resistivity. Unit works on chargeable battery. Necessary accessories along with charger are provided with unit. Features Measurement up to 0.1 Ohms Accuracy up to 2% Digital display Generated signal is not in range of harmonics of mains supply to avoid interference Test resistor are provided to confirm calibration Low battery consumption Battery is chargeable maintenance free type Heavy duty accessories provided for proper reading Operation Short left side two terminals E1 & P1 and connect it to point whose resistance is to be measured. This wire should be shortest possible. Connect other 2 wire provided along with unit to other two terminals. Fix the rods at app.10 to 15 meters in different directions. Pour a glass of water on the rod to make good contact. Select 2V range & press test button. Then display will give direct reading of earth resistance.  

Lcr Meter, digital lcr meter, Led Dome Lights

Side Mounted Magnetic Level Indicator, Conical Basket Strainer

Flow Meters, Fls-03 Level Switch, FLS-04 Level Switch, FLS-05 Level Switch

digital earth tester, line testers, board band line testers

Flow Meters, conductivity indicators, flow transmitters, Flow Indicators

Energy Meter, Barcode Label, pressure sensitive labels, Stickers

battery monitors, battery management systems, Line Of Sight Surveys

pH Meter, electronic microcontroller, Rgb Controller